Only show results available in Virginia? Ok

gas analyzer manufacturer Applications

  • Gas detection analyzers for storage

    Flammable & combustible liquids are found in virtually every industrial plant. The quantities of these can vary from a few ounces in aerosol cans to several thousand gallons in bulk storage tanks. The principal hazard associated with storage is the accidental discharge or release of the flammable or combustible material into the surrounding area.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Premium

    Chemiluminescense based analyzer for industrial applications

    Whether combustion, waste incineration or power plant, most of the hot processes call for a measurement of the exhaust gas direct at the source by national laws and international standards. No matter where and at what concentrations nitrogen oxides have to be detected, you can depend on ECO PHYSICS analyzers to handle the job quickly, reliably and with a precision that is unmatched anywhere in the world. Whether at trace levels in a clean room environment or for the analysis of exhaust gases directly at the source, you will find the type of chemiluminescence detector (CLD) to perfectly suit you at ECO PHYSICS.

    By ECO PHYSICS AG based in Duernten, SWITZERLAND.

  • Premium

    Gas monitoring instruments and systems for semiconductor manufacturing

    In the semiconductor manufacturing industry, various perfluorinated compounds (PFCs) are used. The emissions of the PFC compounds into the ambient air are reduced by scrubbing of the exhaust gases from the process. In this process, the Gasmet™ FTIR Gas Analyzers can be used to measure the emissions into the atmosphere and also monitor the efficiency of the scrubbers. Typically monitored PFCs in the exhaust gas include carbon tetrafluoride CF4, trifluoromethane CHF3, and hexafluoroethane C2F6.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Medical Gas Analysis for Process Industry

    USP37 Medical Gas requires a specific, selective and positive identification test using a paramagnetic signal. Regular analysis of medical gas is required to ensure that the oxygen concentration is NLT 99.0% volume. Following the appropriate United States Pharmacopeia standards, in this case specifically USP37, requires an analyzer which uses a paramagnetic based technology.  The Systech Illinois Paramagnetic Oxgyen Analyzer PM700 is perfectly suited for this medical gas analysis application.

    By Systech Instruments Ltd based in Thame, UNITED KINGDOM.

  • Gas detection analyzers for semiconductor industry

    Semiconductor manufacturing facilities employ a number of hazardous gases in their production processes. Whenever these gases are stored, distributed or used in manufacturing processes, there exists the potential for a hazardous condition. The primary hazards associated with these gases include fire, explosion, and contamination resulting in product loss or unscheduled preventative maintenance. These gases must be continuously monitored to ensure the health and safety of employees, to protect property, as well as to maintain regulatory compliance. Continuous gas monitoring in semiconductor facilities is a requirement of local and state regulations.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Integrated real-time gas analysis solution for emissions industry

    Pollutant emissions from industrial smoke stacks are a major national concern due to both health concerns and climate change. As a consequence, there are at least tens of gas analyzer manufacturers in the U.S. alone that compete in that market and have done so for years. What CIC Photonics brings to that competitive field is its expertise derived from its Combustion Efficiency Solution and its high performance IRGAS Systems. The IRGAS-CEM provides real-time and simultaneous measurements of the multitude of toxic combustion products, including CO, CO2, NOx, SOx, CH4, CxHy, H2S, etc. The EP-IRGAS-SPA is also applicable for fast time responses.

    By CIC Photonics, Inc. based in Albuquerque, NEW MEXICO (USA).

  • Premium

    Gas monitoring instruments and systems for phosgene monitoring

    Phosgene COCl2 is a colorless gas. While it has been used as a Chemical Weapon Agent (CWA) in the past, currently this poisonous gas is also an important reagent in synthesis in the pharmaceutical and chemical industries. The plants using phosgene are typically equipped with gas sensors to detect leaks in the indoor ambient air. The critical situations arise when equipment in contact with the gas at the manufacturing facilities are serviced and maintained. As phosgene is very poisonous, even small gas pockets in serviced equipment may be dangerous to maintenance personnel. Gasmet™ FTIR Gas Analyzers are ideal tools to monitor point sources of phosgene. The measurement technology has high specificity, may be operated continuously, and has a fast response time.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Testing Fume Hood Flow Dynamics using SF6 as a Tracer Gas

    A safe laboratory environment requires an effective method for clearing toxic material from fume hoods. Since all handling of toxic materials is completed in these hoods, it is critical to have a procedure to evaluate their operation to assure adequate protection for laboratory workers. The InfraRan Specific Vapor Analyzer, factory calibrated for SF6, is an ideal instrument for measuring fume hood efficiency in accordance with ASHRAE and other standards. Manufacturers identify the flow dynamics (factors that affect air flow in the hood and performance with air) using the ratings AM (as manufactured), AI (as installed), and AU (as used). A fume hood evaluation conducted under its operational environment is critical, as these tests will indicate any installation shortcomings as well as direct workers in proper laboratory hood techniques.

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • Premium

    Benzene Monitoring

    Cerex Monitoring Solutions manufactures UVDOAS analyzers for a variety of Benzene monitoring applications. As benzene specific single gas or multi-gas analyzers, our instruments are available with application specific detection ranges and fully configurable alarm functionality.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you