Only show results available in Virginia? Ok

gas burner Applications

  • Flaring Solutions for Gas Processing Facilities

    ABUTEC’s proprietary technology was designed to provide cost-competitive solutions and the industry’s lowest operating costs and cost of ownership. Our uniquely engineered burner system offers a significant reduction in make-up fuel over premixed surface combustion systems, thermal oxidizers or traditional pipe flares. In addition, we meet EPA requirements for 40 CFR 60.18 and local BACT (Best Available Control Technology) and MACT (Maximum Achievable Control Technology) at the state and local levels. We will perform a complete return-on-investment analysis for you while showing you your total cost of ownership.

    By ABUTEC LLC based in Kennesaw, GEORGIA (US) (USA).

  • Premium

    Very large waste gas volumes with low contaminant concentration

    The CTP desorption allows for an especially high concentration factor which, in turn, reduces the cost of ownership and permits an auto-thermal operation (additional burner switched off) even when the contaminant concentration is low.

  • Flares for Safe Disposal of Waste & Toxic Gases

    Our Flares are versatile in design & suitable for total destruction of waste gas/vapours. The waste gases/Vapours from petrochemical, WWTP, chemical plants have very high potential for environmental hazards. If allowed to released unburned into atmosphere. SIES offers flares and combustion systems for safe disposal of gases with high efficiency and reliability. System Designed to meet the API 521/537 norms High efficiency Burners with up to 99% thermal destruction Flares operable on fully automated, SCADA based solutions Customized & Cost effective project specific solutions Successful Installations of various types of flares at various locations.

  • Gas detection analyzers for pulp & paper mills

    Flammable non-condensible gases (NCG’s) are byproducts of the wood pulping process. Health and pollution regulations prohibit the release of these gases into the atmosphere. They are usually eliminated by passing them through an incinerator or by using them as fuel in the burner of a boiler or kiln. The incinerator, boiler or kiln however can be damaged by NCG’s which have built up explosive levels. Pulp mills require the use of our PrevEx Flammability Analyzers to monitor the NCG stream and detect and divert these dangerous concentrations before they can cause damage and shut down the mill. The PrevEx analyzers accurately measure the total concentration of flammable gases present in the NCG sample. Their high sampling speed dramatically improves response time—an important factor in pulp mill applications.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Premium

    Several waste gas streams: Short, high concentration peaks and a constant |medium concentration

    Concentration peaks and liquid waste posed a tough challenge on the air pollution control system. With the CTP solution, this waste is not only disposed of but also reduces the burner energy considerably.

  • Biogas for Cooking

    This solution comprises a Biogas Digester of desired capacity working with specific substrate as input. It may or may not have H2S scrubbing system, depending on the quantity of H2S in the biogas and the requirement by the customer for cleaning it. As the heating value of biogas is almost half that of cooking LPG, specially designed biogas burners are provided to improve cooking speed. Depending on the demand by the customer, a blower to increase gas pressure may be employed.

    By Kirloskar Integrated Technologies Limited based in Kothrud, INDIA.

  • Flaring Solutions for the Petrochemical & Refinery Industry

    ABUTEC’s goal in the petrochemical and refinery industry is to save you money. ABUTEC’s vapor combustor and enclosed flare line offers flexible and resilient burner technology to handle heavy hydrocarbon gases down to low quality or inert gases. We will save you money on capital costs and we will offer you a very fast payback (as low as 2 months) based on reducing the amount of make-up fuel and pilot gas required. This revolutionary technology is designed for you!

    By ABUTEC LLC based in Kennesaw, GEORGIA (US) (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you