Only show results available in Virginia? Ok

gas power plant Applications

  • Sulfur monitoring in gas feedstock for fuel cell power plant

    Trace level sulfur measurement (

    By MKS Instruments, Inc. based in Andover, MASSACHUSETTS (USA).

  • Premium

    Water treatment for power plants

    The process of electricity generation from fossil fuels such as coal, oil and natural gas is water-intensive. Between 40-50% of all water abstracted and used in developed countries is used in the generation of electricity. Thus, a reliable, abundant and predictable source of raw water supply to a power plant is a critical factor in site selection. Water supplies are required to provide various process waters for the following essential main purposes such as make-up water, cooling water for steam turbine condensers, and auxiliary plant cooling water.

    The primary application of modern water treatment technology is to maintain the integrity and performance of the power plant. Critical plant applications have water purity or conditioning requirements that must be adhered to for safe, reliable and efficient power generation.

    Experience has shown that integration of water technology treatments with power plant design can be very important in reducing operational problems and component failures 

    At power plant worldwide there are increasing limitations on water availability and environmental restrictions on discharges. This is expected to promote measures for water conservation and to have an increasing influence on water treatment decisions. At power plant, the recycling of internal wastewater streams can extend from the recovery of individual high-quality waste streams, which can be reused either directly or after only limited treatment, through to the development of fully integrated water/wastewater treatment systems for zero liquid discharge. However, the application of reuse schemes requires site-specific assessment, as not all waters may be viable options for recovery.

  • Environmental monitoring solution for power plant

    The construction of coal and natural gas power stations is continuing at a steady rate along with older power stations being retrofitted with more effective flue gas cleaning systems. Both the community and environmental protection authorities are paying closer attention to both emission and ambient concentrations around power stations.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Gas Detection Solutions for Power Generation Industry

    Boreal possess an array of products for the power generation industry from emissions stack monitoring, boiler room monitoring, chloride leak detection, and ammonia slip in deNOX. Boreal’s products are tailor made for coal fired power plants, natural gas fired, and waste-to-energy. Whether gas detection is used for safety, process, or environmental reasons, Boreal has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Coal Combustion Residuals Disposal for Power Plants

    Coal combustion residuals (CCR) are generated during the power generation process and can include fly ash, bottom ash, boilerslag, and flue gas desulfurization (FGD) residuals. CCRs contain trace concentrations of heavy metals and therefore cannot be dumped or stored where rainwater can leach the metals. Liner systems can be used to contain the coal combustion by-products and protect them from leaching into the environment.

    By CETCO based in Hoffman Estates, ILLINOIS (USA).

  • Hydrocyclones for flue gas desulfurization FGD power applications

    KREBS Flue Gas Desulfurization Cyclones: High capacity Krebs gMAX® cyclones for reagent preparation and gypsum dewatering in FGD systems. Our Hydrocyclones and Technequip Knife Gate valves are used in Power Plants around the world.

    By FLSmidth KREBS based in Tucson, ARIZONA (USA).

  • Waste tyre recycling fuel oil pyrolysis plant

    Waste tyre recycling the obtain thing as follows: 45%-55% fuel oil, 10%-15% steel wire, 30%-35% carbon black and 8%-10% flammable gas. You can get diesel from fuel oil by distillation plant. You can get a very high profit by disposing these wastes, and also it's helpful for improving the local environment, avoid garbage pollution . As the fuel material used in Cement factory, glass factory, ceramic factory, electric power factory, steel making factory, boiler factory, etc. 2. Final diesel come out from our distillation plant and deodorant & decolorant can be used in diesel generator. 3. Used in diesel powered cars, such as vans, truck, tractor, etc. 4. Use as heating oil, industrial and home. Carbon black : 1. Make it to briquette for fuel. 2. Used in rubber and painting factory after carbon black grinding to 200-4000 mesh. Contact: Ms Bonnie Phone: +86-371-5677 1821 +86 15893800169 Skype: bonniezhao2 Email: oilmachine@doinggroup.com www.wastetireoil.com

  • Premium

    Actuators for the power generation

    As well as traditional power stations, applications for Rotork products are found on renewable energy generation such as solar thermal plants and on CO2 emissions reduction processes such as flue gas desulphurisation and carbon capture and storage.

    By Rotork based in Bath, UNITED KINGDOM.

  • Power Plant Coal Fired Boiler Filtration

    Dust filter PPS Filter Bags For Coal Fired Boiler Gas Filtration.

    By Zhejiang Grace Envirotech Co., Ltd based in XIAOSHAN, CHINA.

  • Low emissions auxiliary boilers to coal or otherwise fired power plants

    Whether providing high-efficiency, low emissions auxiliary boilers to coal or otherwise fired power plants across the United States, or heat recovery steam generators to natural gas fired turbine plants you will find Superior Boilers serving the needs of power generation customers for years to come.

    By Superior Boiler Works, Inc. based in Hutchinson, KANSAS (USA).

  • Power Industry

    Our activities are closely interconnected with the energy industry. The precision casting foundry casts rotor and stator blades for gas turbines followed by precision grinding by the Industry Division. Furthermore, we also perform machining of shafts, complete blade attachment as well as subsequent assembly of steam and gas expansion turbines. PBS ENERGO, our affiliate company, focuses on the design and manufacture of steam and gas expansion turbines, including the delivery of complete plant systems. Our colleagues in První brněnská strojírna, a.s. specialise in the manufacture of boilers for various types of power plants. From design up to complex deliveries. Our products are subjected to extensive quality testing. Quality Management System according to ISO 9001 is fully implemented in our production process.

    By PBS Velká Bíteš, a.s. based in Velká Bíteš, CZECH REPUBLIC.

  • Premium

    Corrosion-resistant materials for the power industry

    Sauereisen is the most widely known international company to supply corrosion-resistant coatings, mortars and gunitable refractory linings for flue gas applications in the power industry. For more than half a century, our cost-effective corrosion-resistant materials have provided solutions for power plants and their various components where the infrastructure would otherwise be threatened by corrosion. Our diverse product line includes potassium silicate, novolac epoxy, vinyl ester and urethane formulations engineered to meet the challenges of each operating environment.

    By Sauereisen Inc. based in Pittsburgh, PENNSYLVANIA (USA).

  • Power Generation

    Combustion turbines A gas turbine, also called a combustion turbine, is a type of internal combustion engine. It has an upstream rotating compressor coupled to a downstream turbine, and a combustion chamber in-between. The basic operation of the gas turbine is similar to that of the steam power plant except that air is used instead of water. The turbine shaft energy is used to drive the compressor and other devices such as an electric generator that may be coupled to the shaft. The energy that is not used for shaft work comes out in the exhaust gases, so these have either a high temperature or a high velocity. A catalyst is often used to treat these exhaust gases to comply with emissions regulations. EmeraChem has installed OEM and after-market catalyst in over 240 applications

    By EmeraChem based in Knoxville, TENNESSEE (USA).

  • Premium

    Fly Ash - Industrial Vacuum

    Fly Ash can cause many problems. The Vac-Con & Vector Pneumatic Vacuum systems can assist and solve many of these problems. Our high-performance vacuum systems are manufactured in three basic configurations: Truck mounted, Trailer mounted, and Fixed/static installed. Any of these systems can be integrated into the existing power plant design. All of our vacuum systems can be utilized to solve your plant’s fly ash removal/clean-up needs and can assist in many other maintenance projects. All can be tailored to fit into your power plant’s specific needs. Vac-Con Truck mounted Industrial vacuum systems are equipped with large storage debris tanks with self-cleaning intake filter systems. The Industrial Trucks vacuum the waste products through existing manifold piping or with hoses attached directly to the debris tank. When fully loaded, the truck can then drive directly to the disposal site and discharge the waste products. The Industrial Truck offers a great amount of flexibility of operation and can be utilized anywhere in your facility for many different types of normal and emergency maintenance operations. The Vac-Con Industrial Vacuum Truck can be utilized on both wet and dry materials. The same Vac-Con truck can be used for removing Fly Ash from your plant, coal from broken intake belt conveyors, or used to suck wet muddy material from storage lagoons. The Vector Trailer mounted Vacuum Systems are designed to be used in several locations around power plants. The Trailer mounted Vacuum Systems connect to Manifold piping located in key areas within your power plant. The Vacuum systems move the waste products from the plant and deposit these products into moveable storage containers. The loaded storage containers when full can then be moved to the disposal sites for discharge. Vector Static Mounted Vacuum systems are designed to vacuum and remove Fly Ash and other bulk waste products through manifold piping from operational areas of the plant and deposit these waste products into collection storage silos for later transport to disposal sites. The fixed vacuum systems are electric motor driven and are normally installed as a permanent addition to in-plant existing conveying systems. Please contact us with any requirements you may have. We will evaluate your request and respond with solutions specific to solve your problems and fit your needs.

    By Vac-Con, Inc. based in Green Cove Springs, FLORIDA (USA).

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Monitoring solutions for the gas analysers areas

    Most large coal fired power plants and combustion processes are required to monitor CO, NO and NO2 (NOx), SO2 and possibly CO2; in addition the analyser has to be normalised to Standard conditions. For this application CODEL offers the five channel GCEM 40 series which uses Infrared absorption to measure these gases plus moisture, pressure and temperature.  The analyser can be configured for single channel operation to monitor any of these gases plus CH4 and HCl.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Gas monitoring during industrial process

    EM-5 CEMS Coal power plant: Entrance of SCR denitration device, NOx O2 Exit of SCR denitration device: Measure remanet NH3 after reaction and avoid blocking by crystallization, NH3; Calculate denitrification rate with Nox input, NOx O2 Gas-fired power plant: Counting tail gas emission and realtime concentration, NOx O2 SO2 Temperature pressure flow dust

    By HANGZHOU ZETIAN TECHNOLOGY CO., LTD based in Hangzhou, CHINA.

  • Solutions for mercury removal emissions from flue gas streams

    For the removal of mercury emissions from flue gas streams, Calgon Carbon`s specialty PAC products are proven industry performers. These industries include: Coal-fired electric power plants, Cement, Boilers.

    By Calgon Carbon Corporation based in Pittsburgh, PENNSYLVANIA (USA).

  • Premium

    Carbon capture and storage (CCS) applications

    Carbon Capture and Storage (CCS) is an emerging method of reducing greenhouse gas (GHG) emissions of power plants. In a process called ‘scrubbing’, the carbon dioxide emissions can be absorbed into chemical solvents consisting of amines or carbonates. Scrubbing is a well-established method of carbon capture, with virtually every commercial CO2 capture plant in operation using this process. In the process, the first step is the removal of impurities from the flue gas, such as hydrocarbons and oxides of both nitrogen and sulfur (NOx and SOx). Next the purified gas is passed through an absorption column filled with the chemical scrubbing solvent. The solvent reacts with the carbon dioxide and selectively absorbs it from the gas stream. When CO2-rich solvent is heated, the carbon dioxide is released as a nearly pure gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you