industrial hazard Applications
-
Hazardous waste analysis for the hazardous waste industry
By Grabner Instruments Messtechnik GmbH based in Wien, AUSTRIA.
-
Pump control for the hazardous solid industry
By Pulsar Process Measurement Ltd based in Worcestershire, UNITED KINGDOM.
-
Spill containment for the hazardous substances industry
By GLOBAL Wastewater Treatment Systems, Inc. based in Grand Island, NEBRASKA (USA).
-
Lamp recycling for the hazardous waste recycling industry
By MRT System International AB based in Karlskrona, SWEDEN.
-
Weighing-400.jpg)
PremiumIndustrial Weighing - Hazardous Area (Ex) Weighing
Explosive areas need special consideration, but performance should not be compromised. That’s why METTLER TOLEDO has built the most extensive range of hazardous area (Ex) products available from a range of compact, bench, floor, custom, load cells and vehicle scales up to 2000 tons. Many of our products comply with the new European ATEX directive for Group 2 and 3 devices, Factory Mutual, Canadian Standards as well as many country specific regulations.
By Mettler - Toledo Int. Inc based in Greifensee, SWITZERLAND.
-
PremiumHazardous waste treatment solutions for metal industry
Sludge by-products from the metalworking industry have a high potential for recycling. Prolonged grinding processes can generate large amounts of highly valuable, alloy-rich sludge; consisting of metal powder and cooling lubricants. Inside our VacuDry system, the thermal separation of the liquids (hydrocarbons, eventually water) and solids (metal powder) takes place in an oxygen free atmosphere. This absence of oxygen ultimately eliminates material degradation by oxidation, and self-ignition or explosion risks. Operation under a low vacuum ensures the possibility to recover the cooling lubricants for later reuse. After the thermal treatment, for appropriate handling in the melting process, the metal powder is pressed into briquettes. With the econ VacuDry technology, 100% recycling of all ingredients is possible.
By econ industries GmbH based in Starnberg, GERMANY.
-
PremiumHazardous waste treatment solutions for chlorine industry
The mercury cell process is a formerly widely-used production technique for the production of chlorine and caustic soda. The liquid metal, mercury, acts as cathode (negative pole) in this process. In the past, the loss of mercury during the process (to air, soil and water) led to serious health and environmental problems. Therefore, most European chlorine producers have decided to phase out the mercury cell process by 2020. Nevertheless, even today, almost 6000 tons of mercury is used per year for chlorine production in Europe alone. As a result of this, yearly waste outputs contain around 1200 tons of mercury, which are stored on-site or sent off for disposal.
By econ industries GmbH based in Starnberg, GERMANY.
-
Premium
Hazardous chemicals management for the health care industry
By RegScan, Inc. based in Williamsport, PENNSYLVANIA (USA).
-
High Intensity Discharge lamp recycling for the hazardous waste processing industry
By MRT System International AB based in Karlskrona, SWEDEN.
-
Fluorescent tube recycling for the hazardous waste processing industry
By MRT System International AB based in Karlskrona, SWEDEN.
-
PremiumHazardous waste treatment solutions for oil and gas industry
There are a wide amount of applications for our VacuDry® process within the oil and gas industry. A large variety of wastes and by-products that are generated in the oil & gas production chain can be treated effectively and sustainably. In past decades, numerous thermal desorption processes have been implemented worldwide, using a variety of heating chamber designs to separate hydrocarbons from the mineral solids. Such standard TDUs work under atmospheric pressure which can lead to safety risks, high energy consumption, larger emissions and limited flexibility regarding altering feed materials. Due to its unique design, the complications outlined above are avoided throughout the VacuDry® process. When it comes to treating standard oily wastes, mercury-containing waste streams, NORM, and especially for the recovery of highly valuable drilling fluids from drill cuttings; our vacuum thermal desorption process (i.e. vacuum distillation) is economically unbeatable.
By econ industries GmbH based in Starnberg, GERMANY.
-
Stack Testing for Medical Waste Industry
By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).
-
-
Applications and Air Pollutants Removed in Hazardous, Solid and Liquid Waste Treatment Operations
Venturi scrubbers with FORCE FLUX Condensation technology and Wet Electrostatic Precipitators for industrial, municipal, sewage sludge and pathological waste incinerators to remove micron, submicron particulate, heavy metals and acid gases. Special quencher/scrubber systems for dioxin removal. HCL scrubbing from PVC plastic waste burning. Fine particulate, acid gases and NOx removal on munitions destruction. Cleanup of all pollutants from liquid waste incinerators and other high temperature destruction processes. Acid and particulate emissions from electronic board and metals recovery operations.
By Bionomic Industries Inc. based in Mahwah, NEW JERSEY (USA).
-
Stack Testing for VOC Recovery Afterburner Installation
By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).
-
PremiumIndustrial air pollution control for the chemical and petrochemical industry
CTP systems can be found in every leading production company: thanks to the experience and the expertise developed in partnership with our customers for processes with inconsistent waste gas volumes; varying concentrations of organic components; gases contaminated with aerosols. CTP has installed systems for waste gas streams ranging from 1,000 to 200,000 Nm³/h. CTP supplies this industry with mainly catalytic systems, regenerative thermal oxidisers (RTO) and adsorbers. As the flue gases in this industry are often explosive mixtures, CTP systems have to be completed with special safety conduits and filters to help reduce hazards during continued operation.
By Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control based in Graz, AUSTRIA.
-
Industrial shredders for CIW/MSW/BW/HW industry
By PRECIMECA Environnement based in Toulouse, FRANCE.
-
Premium
Waste recovery for construction industry
Construction waste consists of unwanted material produced directly or incidentally by the construction industry. This includes materials that may contain lead, asbestos or other hazardous materials. There is increasing pressure on the construction industry to dispose of this hazardous material in an environmentally responsible manner. Tetronics can help alleviate this pressure by providing waste recovery plants to deal with all types of hazardous wastes generated from a construction projects lifespan: from land remediation through to the treatment of APCs from incineration as well as the treatment of asbestos.
By Tetronics (International) Limited based in Swindon, UNITED KINGDOM.
-
PremiumSustainable solutions for electronics industry
Get the power tools to create sustainable success. We have worked with some of the leading technology companies in the world. In fact, thinkstep has completed hundreds of projects with ICT companies, including ecodesign assessments and programs for mobile phones, printers, computers, servers, semiconductors, car electric and electronic systems, e-motors, transformers, and many more products. With 20 years of global sustainability experience, we are deeply engaged in addressing the growing disclosure expectations on product carbon footprints, materials of concern, and labor practices in the supply chain, plus regulations on hazardous materials, toxicity, and end of life management. We don’t merely identify what you need to eliminate; we strategise with you to increase revenue, strengthen supply partnerships, and enhance your brand profile.
By thinkstep based in Leinfelden-Echterdingen, GERMANY.
-
Premium
Waste Management Solutions for Metal Manufacturing Industry
There are several challenges faced by the metal manufacturing industry. Firstly, there is a drive to recover as much metal credit as possible before disposal of by-products as wastes. Secondly, there is a requirement to minimise waste generation or alternatively minimise the costs of managing the disposal of any hazardous waste material generated during the manufacturing process. Finally, keeping the company competitive by generating value or by reducing costs in the manufacturing process. Any solutions that can overcome these challenges must be considered. Tetronics can assist with a range of metal manufacturing waste challenges, including:
By Tetronics (International) Limited based in Swindon, UNITED KINGDOM.
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you