Only show results available in Virginia? Ok

laboratory gas system Applications

  • Premium

    Gas analysis & monitoring system for semiconductor

    The Cleanroom is a combined laboratory chemical, mechanical and / or electronic whose main characteristic is the presence of very pure air, that is a very low content of fine dust in suspension. In the process of semiconductor production, the airborne particles (micro-powder) go to irreparably damage the micro-photoetched that form the chip, creating an electronic circuit defective, and then discarded. This process has forced the improvement of industrial production environments, removing particles from the air, for two purposes: to increase the efficiency of production, increasing the yield of quality, and requirement of the manufacturer (of course based on the demand of the market) in shrink increasing the area of etching of semiconductors (just think of the USB storage media in a few years, went from 16 MB to 16 GB without changing the external dimensions).

    By ETG Risorse e Tecnologia based in Montiglio, ITALY.

  • Premium

    Measurement solution for multi-stream combustion research

    Protea supplied a complete turn-key measuring system for multi-point sampling in a University combustion research laboratory. Utilising the latest in FTIR spectroscopy, atmosFIR, a complete cabinet system was supplied containing: atmosFIR FTIR Gas analyser, Sampling System Control Module (SSCM), Heated Stream Selection Module (HSSM), Temperature Control Module (TCM), 4 heated sample lines, 4 heated sample probes, Embedded PC controller.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for engine emissions measurements

    The exhaust gas from combustion engines is a complex mixture of gases and particulate matter. The composition of the gas may change rapidly. Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. The analyzer, sampling system and computer can be assembled on a cart for use in a dynamometer laboratory, or the portable version can be used for roadside tests.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for flavoring agents

    Manufacturing of powdered and liquid flavorings and fragrances involves production phases where flavoring chemicals may be released into the ambient air breathed by workers. Exposure control by gas analyzers in the production rooms and laboratories is necessary to ensure that the Time-Weighted Average (TWA) concentrations do not exceed the maximum Permissible Emission Limit (PEL) values.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Computerized instrumentation for the medical gas flow and scientific research

    Environics gas mixing, blending and dilution systems provide for precise mixing of gases for a wide variety of clinical applications. Our systems can produce gas concentrations from percent to ppb levels for single or multi-point calibration. The high accuracy of our mixers make them the units of choice for a wide variety of laboratory and research applications. For example, Environics Biological Atmosphere Incubation Mixers provide stable and accurate gas mixes for any laboratory or clinical need. You can generate the specific reduced oxygen environments needed for anerobes as well as the enriched oxygen environments needed in a variety of cellular, viral and high density culture applications. Systems can also be used to create a specific and stable gaseous environment in a clean room. In all cases, the Environics Atmosphere Mixers allow you to use less expensive single-gas cylinders or bulk tanks in place of a high number of expensive blended cylinders.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Measurement solution for VOC emissions monitoring

    Protea has used our VOC gas analysers in many projects requiring the monitoring of complex mixes of VOCs. In the chemical and pharmaceutical industry, VOC abatement plants such as scrubbers and carbon-bed systems are typical installations where the use of Protea analysers and our VOC analysis expertise have proved valuable to plant operators. They prove a very powerful and flexible tool in both process gas measurements and VOC emissions monitoring. In the laboratory, Protea can deliver instruments with all the chemometric software and support to enable users to measure hundreds of gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Measurement solution for medical workplace monitoring

    In taking a responsible stance on the exposure of workers to any potential hazardous gases, there is a need for workplaces using anaesthetic gases, such as hospital operating rooms or research laboratories, to control the level of waste anaesthetic gas in the ambient air. Anaesthesia machines, ventilators, breathing systems and waste gas scavenging systems will all contribute to te background level of he anaesthetic gases that are present in the environment within a facility, whether those machines are in a good state of repair or not. Recovery rooms can become polluted, for example from gas exhaled by the patient, and clean-up from any spills can remain in the background air for long periods.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Low concentrations monitoring of benzene and aromatic hydrocarbons (BTEX) for pollution control and environmental monitoring

    With over 15 years of experience in the measurement of volatile organic compounds (VOC), Environment SA announces the VOC72M, a new generation analyzer for the measurement of BTEX compounds by gas chromatography with photo-ionization detector (PID). The VOC72M can handle up to 40 compounds and eight configurations for analysis. This compact and fully automated analyzer with wide voltage range specifications (90-240V) provides equivalent performance to the laboratory chromatographs and is particularly suited to fixe or mobile ambient air quality monitoring laboratories. The VOC72M is fitted with a PID detector new generation, much more sensitive, more stable and whose lamp does not need to be cleaned; the analyzer integrates flow control fittings a 3 levels security system built on and uses only one gas (nitrogen). This robust and low maintenance instrument performs all the functions (sampling, analysis and data management) in a simple and completely autonomous mode. It is a particular

    By Environnement S.A based in Poissy, FRANCE.

  • Aerospace

    Our Auxiliary Power Unit (PEJ/APU) and Environmental Control Systems (ECS) are used by aeroplane and helicopter manufacturers all over the world. The successful products of the company also include the range of Main Power Units – turbine, turboprop and turboshaft engines for small manned and unmanned airplanes and helicopters. We provide also subdeliveries for the aerospace industry, for example electroplating, precision casting of guide wheels and blades of gas combustion turbines for aircraft engines, or precision machining. The testing laboratory, where final products are tested, is an important part of the aerospace programme. The production process is controlled by the quality system according to AS 9100, ISO 14 001 and ISO 9001.

    By PBS Velká Bíteš, a.s. based in Velká Bíteš, CZECH REPUBLIC.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you