Only show results available in Virginia? Ok

oil-in-water analyser Applications

  • Oil in Water Monitoring

    Detection of hydrocarbons within both water sources and effluent intake to Waste Water Treatment Works is an increasing requirement. The UviLux Hydrocarbon fluorometer detects hydrocarbons in water at very low concentrations. This in-situ fluorometer provides a rugged sensor which can be deployed in a wide variety of configurations. The UviLux is part of the Lux range of CTG fluorometers, and can be provided with a number of options with regard to signal protocols, and has available accessories to enable in-flow monitoring as well as inclusion within portable systems for taking measurements in the field.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Premium

    Oil in Water Analysis for Flowback or Produced Water

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water. Waiting for remote lab results can take several days to a week. InfraCal TOG/TPH Analyzers allow for oil in water testing at the well site in less than 10 minutes. The sampling requires a few simple steps that can be performed by non-technical personnel. The water is mixed with the extraction solvent, shaken, and then presented to the analyze for measurement. The same InfraCal TOG/TPH Analyzer can be used for TPH in soil if a spill or pond leak occurs to determine the contaminated area. The analyzer features: -Results in under 15 minutes -Detect levels as low as 10 ppm -Portable, rugged, lightweight, easy-to-use -Battery operable -Ideal for field or lab use

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • Oil & Concentrates Analyses

    By Innov-X Canada based in Vancouver, BRITISH COLUMBIA (CANADA).

  • Laboratory equipments for fat oil & grease FOG in waste water

    Measurement of Fats, Oils and Grease (FOG) in waste water is a crucial parameter in water quality control and environmental monitoring performed by water suppliers’ laboratories and environmental authorities; the contamination builds up in the sewerage system and will eventually lead to blockages. Typically the waste water is analysed by first passing a large volume through a filter then selectively determining the grease build-up on the dried filter by an analytical method.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Premium

    Portable and fixed gas analysers for sewage / waste water treatment AD

    AD of human waste has been common in many countries for years but increasing energy costs now drive efficiency. Sewage processors are large energy users and AD can offset and help manage this.

    By Geotech based in Leamington Spa, UNITED KINGDOM.

  • Laboratory equipments for oil in palm mesocarp

    Measuring the Oil Content in Palm Mesocarp using the MQC Benchtop NMR Analyser. Palm oil is the most widely used vegetable oil, particularly important as a cooking oil, as an ingredient in processed foods, and, increasingly, as a feedstock for both biodiesel production and chemical manufacture.  Oil palm is grown extensively around the world, particularly in Indonesia, Malaysia, West Africa, and parts of South America. Crude Palm Oil (CPO) is extracted from the flesh (known as the mesocarp) of the oil palm fruit by mechanical pressing, and is then refined.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Laboratory equipments for oil in snack food

    Measuring Oil in Snack Food using the MQC Benchtop NMR Analyser. Careful control of oil in snack food is essential in ensuring product consistency in the global snack food industry, one of the fastest growing segments in foods today. It is a highly competitive industry where success requires a high quality and, above all, consistent product to ensure its repeat purchasing.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Laboratory equipments for fat & oil in food

    Measuring Fat and Oil in Food using the MQC Benchtop NMR Analyser. Fat and oil in food play a key role in determining the nutritional value, product quality and consumer appeal of the products in which they are incorporated. Routine and accurate measurement of the fat and oil in food is also necessary to ensure that products are in compliance with labelling statements.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Water Contamination Detection

    Security of water assets is becoming an increasingly major issue that demands immediate and robust alarms for potential contamination. In addition to this, natural growth of algae is a common problem for water asset managers, the results of which can increase maintenance costs of water processing plants as well as directly effecting water taste. The CTG FastGuard fast repetition rate fluorometer analyses information on the physiological state of the algae it monitors within an in-line flow system. A number of key parameters are monitored and analysed by the on-board embedded software, which instantly initiates both an audible and visual alarm on detection of a contaminant within the water system. The FastGuard is a robust low maintenance system which avoids false positives often provided by other contamination detection systems.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Refineries & Refinery Emissions Monitoring & Analysis

    Procal supplies the oil refining industry with both process and emission monitoring analysers to meet a wide range of applications.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Mercury determination in natural, surface, sea, drinking, bottled, mineral, and waste water by cvaas


    Mercury determination in natural, drinking, and waste waters is one of the most popular analyses used for environment pollution and sanitary control. Background concentrations of mercury in natural water are within several ng/l. Maximum national permissible levels for mercury in water lie in the range of 0.16–6 µg/l. For example, the following limits for mercury in drinking water are set, µg/l:
    0.5 – Japan, Russia;
    1 – Argentina, Australia, Brazil, China, EC;
    2 – US EPA, US FDA;
    6 – WHO.

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Sample preparation and pumping systems for wastewater treatment industry

    A wide range of sample acquisition and filtration systems are available to prepare even the most difficult of samples for reliable on-line analyser measurement. The correct choice is often critical to prevent analyser blockage and optimise performance. Cross Flow Filtration The PPM cross flow filter, is a simple in-line device used to protect an analyser from ingress of solids, for applications where sample quality is generally good but occasionally suspended solids may be present. The stainless steel filter removes solids above 50 micron size.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Measurement solution for high NH3 monitoring from wastewater

    Protea was asked to supply a high level ammonia (NH3) measurement system for a waste water treatment plant. The reflux drums at the inlet to two ammonia stripping towers needed to be measured continuously. Protea designed a solution based around our Solus TDLAS analyser platform and a high level dilution system. The Solus analyser was configured for NH3 measurements in the range 0-500ppm. A dilution system incorporating special dilution probe and 19` control panel was installed before the analyser. This gave a dilution level of 600:1, enabling the NH3 analyser to measure in the range 0-30% Volume.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you