oil-water separation efficiency Applications
Ambar’s belt mop oil skimmer is ideal for the API separators because the mop can cover the entire width of the API thus giving the oil no place to hide. The recovered oil can gravity drain from the oil skimmer or it can be pumped to a near by oil storage container. The end result is recycled oil, improved efficiency and lower operating costs.
By Ambar Oil Skimmers based in Westwego, LOUISIANA (USA).
Membrane units, in our days are widely used in the water pre-treatment preparation and are becoming one of the most important technologies in the production of high pure water. Nevertheless they often face problems with scaling and fouling and are therefore limited by frequent maintenance, downtime and high costs. Our treatment programs are specifically designed for membrane units like reverse osmosis, ultra- and nanofiltration and enable to remove or preventive control scaling and fouling. Our main target is to run these plants under environmentally friendly and beneficial economic conditions. Special attention is given to an efficient utilization of energy as well as saving precious water. Kurita develops an efficient and effective treatment concept achieving an optimal economic operation and a maximum operational reliability of a plant.
By Kurita based in Ludwigshafen, GERMANY.
The key to optimizing a hydroprocessing unit is to maximize the life of the catalyst bed and increase energy efficiency of the furnaces. Our goal is to eliminate fouling of the catalyst bed by particles and aqueous fluids and the dissolved components within them as well as fouling of hydrogen recovery membranes and furnace-burner tips.
By Pentair Filtration Solutions, LLC based in Conroe, TEXAS (USA).
The cost and efficiency of the waste water treatment is directly linked to the amount of suspended solids in the water.
The addition of an AZUD System allows:
- Increased efficiency of the treatment equipment.
- Decreases the quantity of chemicals used.
- Avoids the “shadowing effect” created by larger particles in UV disinfection systems.
The installation of AZUD filtration equipments allows the reduction of the total solids in suspension in the water, and:
- Helps to maintain an optimal efficiency of energy in the heat interchange process.
- Reduce the accumulation of particles in the components of the cooling systems.
- Reduce the growing of microorganisms. The higher or lower proliferation of these microorganisms is directly linked to the
- higher or lower availability of organic nutrients which favour the development of the same.
- When reducing the total quantity of suspended solids it is improved the efficiency in the application of chemical products to the treatment of water.
- Decrease the frequency of maintenance labours.
The sizing and frequency of cartridge / bag replacement, in cartridge / bag filters used as pre-filters in fine filtration applications depends directly on the amount of suspended solids in the water. The installation of an AZUD system prior to the cartridge /bag filters permits:
- Decrease in the number of cartridges used – cost savings.
- Decrease in the amount of labor and maintenance required.
- Increase in the efficiency of the cartridge.
- Less down time.
In the secondary recovery stage of an oil reservoir, process water plays a central role, just as in the extraction of natural gas. After the oil exploration, the produced water must be separated from the oil and gas. The process water needs to be prepared in order to be re-injected into the water cycle of production. For this purpose, highly efficient separation methods are required.
By AWAS International GmbH based in Wilnsdorf, GERMANY.
Contec oil mist separators ensures the façade design of ETFE cushions for efficient and environmentally friendly glare-, heat- and UV-protection. Contec GmbH, Bad Honnef is a leading manufacturer of filtration systems, oil mist separators and liquid level measuring technology. The use of the Contec oil mist separator (COMS) in the field of building construction is definitely very innovative and our system has proven again its advantages in environmental aspects.
By contec GmbH Industrieausrüstungen based in Bad Honnef, GERMANY.
Conventional wastewater treatment systems are focused on efficient removal of polluting components. This is commonly done through aeration and separation of formed biomass from the cleaned water. After treatment the water would be discharged onto surface waters or subsoil irrigation. Introduction of polishing steps after these treatment systems opened up the possibilities to reuse water for either irrigation or even potable water. DMT Environmental Technology also implements these solutions with its MemBioRex membrane bioreactor. Nowadays novel technologies enable reuse of saline water within industries such as unconventional oil and gas, industry, agriculture, and mining. DMT Water Technology develops and realises innovative products to enable our customers to meet these challenges.
By DMT Global Environmental Solutions BV based in Joure (NL), NETHERLANDS.
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you