Only show results available in Virginia? Ok

petrochemical wastewater Applications

  • Biological wastewater processes for petrochemical

    This wastewater typically contains a lower biochemical to chemical oxygen demand.  We determine biodegradability of each waste stream and the presence of toxic or inhibitory compounds. 

    By Biowater Technology based in Cumberland, RHODE ISLAND (USA).

  • Petrochemical Waste Degradation

    Waste Water Treatment Plants, Landfill Leachates, Refinery Lagoons, Degreasing and Land remediation.

    By Cleveland Biotech Ltd. based in Stockton on Tees, UNITED KINGDOM.

  • Premium

    ppm Measurement of Oil in Water for the Petrochemical Industry

    Measuring the oil content in water or soil is a specialty of Wilks Enterprise. InfraCal TOG/TPH Analyzers provide on-site ppm measurements to help ensure upstream or downstream wastewater complies with discharge permits to avoid potentially costly fines. There are over 3,000 InfraCal TOG/TPH Analyzers in operation today around the world measuring the oil and grease levels in produced water on drilling platforms, oil content in FRAC water, hydrocarbons in wastewater effluents from refineries, and TPH in soil at remediation sites.

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • TOC Correlation to BOD or COD

    Challenge: Biochemical Oxygen Demand (BOD) and Chemical Oxygen Demand (COD) are traditional parameters analyzed in the laboratory to determine organic matter in water and wastewater. Wastewater facility operators need to have constant data to monitor their discharges and optimize treatment processes (biological treatment, chemical dosing, etc). The requirements of BOD and COD analysis prevent them from being implemented as control parameters, however. The BOD five-day analysis time requirement does not allow an operator to use the data for process optimization and. although COD requires less time than the BOD, its analysis includes the use of hazardous chemicals and has no constant analysis capability.

    By GE Analytical Instruments based in Boulder, COLORADO (USA).

  • Premium

    Specialty Cleaners and Lubricants for Filter Membrane Industry

    International Products Corporation has been selling cleaners to the filter membrane industry for over 30 years. Our proprietary formulated cleaners work effectively at restoring 100% flux at safe pH ranges.  We have a wide variety of chemistries available for all membranes and soils and an on-site R&D laboratory that offers technical support and assistance.  All of our cleaners are free of solvents, phosphates, silicates, phenols, and Substances of Very High Concern.

    By International Products Corporation based in Burlington, NEW JERSEY (USA).

  • Premium

    Wastewater Treatment

    Many industrial and pharmaceutical processes generate wastewater with volatile contaminants that increase the COD and BOD to a point where discharging to municipal wastewater is very costly or not an option. These contaminants can be removed from the water by distillation, substantially lowering the disposal cost, and, in many cases, the removed components can be further purified and reused in the process. MEGTEC offers the following solutions to remove the volatile contaminants and make wastewater suitable for discharge to most municipal wastewater treatment plants: Stripping columns using direct steam or a reboiler Distillation columns using indirect steam heat sources Our technologies have been applied to a range of processes including wastewater treatment from industries such as Pharmaceutical, Semiconductor, Chemical and Petrochemical.

    By Babcock & Wilcox MEGTEC based in De Pere, WISCONSIN (USA).

  • Premium

    EDI Solutions

    QUA’s FEDI® (Fractional EDI) stacks have superior hardness tolerance compared to the other EDI products on the market. With a dual voltage process this allows for a higher flexibility and tolerance to inlet water conditions, thus lowering the risk of scaling, and improving the plant's design economics and reliability. FEDI stacks are available in three different models which can be applied either for higher hardness tolerance or high water flow rates. MEGA FEDI stacks are ideal for large capacity, high flow systems normally required in heavy industrial projects such as power, petrochemicals, & electronics for high purity water needs. Each stack can handle treated water flow of up to 75 GPM . MEGA FEDI’s unique stackable design minimizes piping, reduces footprint, and makes it simple and easy to install on skids. FEDI-Rx products are specially designed for applications in pharmaceutical, biomedical and laboratory applications where installations require hot water sanitization to meet

    By QUA Group LLC based in Canonsburg, PENNSYLVANIA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you