OPSIS offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been tested and approved by the German TÜV and the U.S. EPA among others, for the best performance and longest calibration interval.
The nature of steel manufacturing processes places severe limitations on the monitoring methods that can be used. Aggressive environments combined with high levels of particulates and gases make the choice very limited.
Make more out of your mill. OPSIS tested and approved monitoring systems provide cost-effective and reliable on-line monitoring of several gas compounds, such as both high and low concentrations of methane, moisture, carbon dioxide and hydrogen sulphide, at several locations.
Process control and emissions monitoring in a brick plant is a challenge due to the high concentrations of HF. The HF is generated in the process and gas phase HF can reach 50 mg/m3 or more. To use an extractive system in this environment will demand a lot of maintanence.
The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.
Opsis provides state-of-the-art monitoring equipment, fully meeting the high standards of monitoring performance and reliability that the cement industry requires. The Opsis in situ systems are designed to withstand environments with high particulate levels and high temperatures.
Waste-to-energy through incineration of waste is an effective way of producing electricity and heat, at the same time getting rid of the possibly hazardous or unrecyclable waste. The waste can be incinerated at specific WtE plants or at plants with permission for co-incineration of waste at biomass boilers or cement kilns. The waste incineration plants are, however, governed by strict emissions regulations.
Procal´s analysers are used extensively in reporting and control applications in modern Biomass plants. The flexible and reliable instruments form the heart of the systems, enabling CO, NO2, NO, SO2, H2O, CO2, O2, dust and velocity to be measured.
Kurz Thermal Insertion Mass Flow Meter systems provide proven accuracy and reliability in the most difﬁcult of EPA Title IV applications with the ability to survive for long periods of time without maintenance.
The process control of a sulphuric acid plant needs good and reliable detection of gas phase sulphur dioxide (SO2). To measure SO2 is a challenge due to the corrosive environment and high concentration of SO2. Several places in the process needs to be monitored and to transport the sample gas is difficult. A large dynamic range is needed as the SO2 concentration can vary between 15% volume and a few mg/m3. Most systems installed need a lot of maintenance, sometimes as often as every day.
Process control and emissions monitoring in a chemical plant is a challenge due to corrosive gases, high dust load, and high temperatures. To use an extractive system in this environment will demand a lot of maintenance.
Process control and emission monitoring in a waste to energy plant is a challenge. A large number of gaseous components need to be measured with high accuracy. Almost 100% uptime is required and the monitoring system needs to be easy to maintain and fast to calibrate.
Process control and emissions monitoring in a glass manufacturing plant is a challenge due to high temperature in the flue gas. The OPSIS DOAS system provides the glass industry with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method that uses an optical path to measure across the duct. A single OPSIS system will measure all relevant gas componensts such as NOX, SO2, CO, CO2, H2O, O2, and others.
Process control and emissions monitoring in a mineral wool plant is a challenge due to the presence of phenol and formaldehyde. To use an extractive system in this environment will demand a lot of maintenance. The OPSIS DOAS system is different and provides plants with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method using an optical measurement path that can operate across the duct.
The Procal 2000 emissions analyser is ideally suited to the harsh environments associated with Paper & Pulp Plants. The in situ, multi-component Continuous Emission Monitoring (CEM) system has an integrated auto-zero and calibration facility, thereby removing the need for intervention by maintenance staff under normal conditions.
An oil refinery or petroleum refinery is an industrial process plant where crude oil is processed and refined into more useful petroleum products, such as naphtha, gasoline, diesel fuel, asphalt base, heating oil, kerosene, etc,. Oil refineries are typically large, sprawling industrial complexes with extensive piping running throughout, carrying streams of fluids between large chemical processing units. The refining process releases a number of different chemicals into the atmosphere mostly Hydrocarbons which...
Contaminated soil and building-rubble can be efficiently treated with VacuDry technology, including a diverse range of toxic and hazardous substances. VacuDry units also have low emissions and low power consumption, making on-site treatment with our mobile units both economically and environmentally sound.