Only show results available in Virginia? Ok

power plant monitoring Applications

  • Premium

    Emissions Monitoring for Power Plants

    Opsis offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been approved by the German TÜV and the U.S. EPA among others.

    By Opsis AB based in Furulund, SWEDEN.

  • Power Plant & Power Station Emissions Monitoring

    For more than 25 years, coal and biomass fired plants have formed the largest installed user base for Procal CEM systems. Throughout this period, there has been increasing environmental scrutiny and process upgrades, including the near-ubiquitous use of after-treatment systems such as sophisticated FGD and SCR.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Photovoltaic Plant Monitoring

    By Nethix S.r.l. based in Castelfranco Veneto (TV), ITALY.

  • Radionuclide Monitoring for Nuclear Power Plants

    The continuing establishment of nuclear power stations around the world pose unique environmental challenges for their operators. Ecotech provides air samplers to nuclear power plants for sampling of radionuclides. A nuclear power plant`s radionuclide monitoring network enables continuous sampling of airborne particles onto sample filters contained within High Volume Air Samplers. These filters are then analysed in a laboratory in order to screen for any radiation releases. The challenge has always been to obtain a sufficiently large volume through the filter in order to exceed the laboratory methods minimum detection limits. Ecotech`s MegaVol Sampler, samples at a flow rate of between 120-150 m3/hr providing a high flow rate in order to collect a sufficient sample mass for laboratory analysis. The MegaVol will maintain volumetric flow rate at a preset volume until the filter is either changed or overloaded. The MegaVol can be equipped with a 3G modem in order to remotely monitor flow rate and other diagnostic parameters such as temperature, pressure and wind speed and direction.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Environmental monitoring solution for power plant

    The construction of coal and natural gas power stations is continuing at a steady rate along with older power stations being retrofitted with more effective flue gas cleaning systems. Both the community and environmental protection authorities are paying closer attention to both emission and ambient concentrations around power stations.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Premium

    Continuous emissions monitoring for power plants

    OPSIS offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been tested and approved by the German TÜV and the U.S. EPA among others, for the best performance and longest calibration interval.

    By Opsis AB based in Furulund, SWEDEN.

  • Sulfur monitoring in gas feedstock for fuel cell power plant

    Trace level sulfur measurement (

    By MKS Instruments, Inc. based in Andover, MASSACHUSETTS (USA).

  • Premium

    Radiation Monitoring for Nuclear Power

    The nuclear industry, including power plants, research centers and fuel cycle specialists are obliged by law to protect their staff, local populations, the environment and the processes they employ. With this in mind, Saphymo has developed a full range of dedicated products and systems, and plays a major role in radiation protection and ionizing radiation monitoring in both France and on an international scale. Saphymo constantly strives to satisfy safety requirements to the full, reinforce its technological know-how in the management of complex systems and anticipate customer needs, and offers adapted solutions in the fields of operational dosimetry, Radiation Monitoring Systems, contamination control, access control, environmental protection and survey meters. Saphymo also offers a broad panel of services intended to maintain its products in operational condition.

    By Saphymo based in Montigny Le Bretonneux, FRANCE.

  • Environmental solution for radionuclide monitoring

    The continuing establishment of nuclear power stations around the world pose unique environmental challenges for their operators. Ecotech provides air samplers to nuclear power plants for sampling of radionuclides.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Hydrocarbons monitoring

    Hydrocarbons are a family of organic chemicals consisting of carbon and hydrogen atoms arranged in a variety of ways. Hydrocarbons are found naturally in crude oil and are released into the environment with its combustion (power plants, home heaters etc).

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Premium

    Continuous emissions monitoring for mercury monitoring

    Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable results.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Measurement solution for VOC emissions monitoring

    Protea has used our VOC gas analysers in many projects requiring the monitoring of complex mixes of VOCs. In the chemical and pharmaceutical industry, VOC abatement plants such as scrubbers and carbon-bed systems are typical installations where the use of Protea analysers and our VOC analysis expertise have proved valuable to plant operators. They prove a very powerful and flexible tool in both process gas measurements and VOC emissions monitoring. In the laboratory, Protea can deliver instruments with all the chemometric software and support to enable users to measure hundreds of gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • HCl Monitoring in Air

    Hydrogen chloride (HCl) is a colorless, sometimes slightly yellow, gas. It is an undesired environmental component that may be damaging to workers and the surroundings. Exposure limits have thus been established by industries to make sure that the workers operate in a safe environment. HCl monitoring is especially required for incinerators, coal-fired power plants, aluminum recycling and cement plants. Unisearch offers a reliable and easy-to-use HCl analyzer – the TDLAS-based LasIR system. Studies have shown that TDLAS equipment provides data that is more accurate than conventional gas monitoring equipment. When calibrated for HCl monitoring, TDLAS is able to detect this gas among other gases present in the area and provide continuous updates with regards to the changes in its concentration.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Gas Detection Solutions for Power Generation Industry

    Boreal possess an array of products for the power generation industry from emissions stack monitoring, boiler room monitoring, chloride leak detection, and ammonia slip in deNOX. Boreal’s products are tailor made for coal fired power plants, natural gas fired, and waste-to-energy. Whether gas detection is used for safety, process, or environmental reasons, Boreal has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • NH3 Monitoring in Air

    NH3 (Ammonia) is a colorless gas with a distinctive pungent smell. Ammonia monitoring is essential in coal-fired power plants, where NH3 is used to reduce NOx emissions. The ammonia consumes all of the NOx, but its high concentration that is needed for these purposes also starts reacting with other things and in the process can clog up filters and cause premature failure of expensive SCR equipment and pre-heaters. Not to mention that these high levels create an irreparable damage to the environment.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Water Monitoring and Flow Measurement Systems for Hydrology

    In recent years acoustic flow measurement and flow metering has established itself as the standard method for measurement in many hydrological stations but is also used as the basis for various applications, for example for flood protection and flood forecasting. Ultrasonic flow meters are also used in hydro-engineering constructions. With this almost contact free technology data can be recorded continuously and it provides 24/7 monitoring. Such flow monitoring is particularly important in waterways used for shipping, transportation, irrigation, drainage and for cooling water extraction of power plants. A further important use of transit-time open channel flow meters is the transportation of water used for the supply of drinking water. Here the focus lies on detecting the flow rate of water loss at an early stage as it is sometimes difficult to detect small leakages.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Premium

    Measurement solution for CO2 capture by amine absorption

    The act of capturing and storing CO2 produced from large scale combustion plants such as power stations is becoming more and more favourable and feasible. One of the most common post-combustion CO2 capture methods is by absorption. The absorption plant can be added on to the existing combustion process, with the flue gas first passing through an absorption column where the CO2 reacts with an absorber. Amines of different types are used as the absorber. An amine CO2 capture plant can capture as much as 90% of the CO2 emitted from the power station and so has a real benefit for the environment. Having said this, care needs to be taken to ensure that amine emissions themselves are monitored, managed and prove no extra damage to the environment. Research is on-going to develop new amines or mixtures of amines to reduce emissions. The most common absorber in use in today’s first generation of industrial pilot plants is Monoethanolamine (MEA).

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you