Only show results available in Virginia? Ok

process gas instrument Applications

  • Premium

    Gas monitoring instruments and systems for DeNOx process control

    In most combustion process atmospheric nitrogen reacts with oxygen in high temperature conditions to produce nitrogen oxides (NOx). Total NOx production is the sum of nitrogen monoxide NO and nitrogen dioxide NO2. The emissions of these gases are controlled through setting of emission limit values (ELVs) for power plants.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for nitric acid process

    Modern production method of nitric acid production may lead to generation of several different gaseous emission components, such as nitrogen oxides (NOx), ammonia NH3 and nitrous oxide N2O. Nitrogen monoxide is an intermediate gaseous product in manufacturing of nitric acid HNO3. NO is formed in a catalytic reaction between ammonia and molecular oxygen O2. But undesirable side reactions may result in formation of nitrogen dioxide NO2 and nitrous oxide N2O. The NO and NO2 emissions can be reduced by use of Selective Catalytic Reduction unit (SCR), which deploys ammonia gas NH3 to limit emissions of NO and NO2. A modern nitric acid plant needs to monitor the emissions of these gases.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for print factories

    Typical modern printing processes utilize solvent-based dyes. The evaporation of the dye solvents into the ambient air during the printing process may expose the workers to various chemicals. Depending on the type of solvents in case, the solvents have different long term exposure limits, which should be obeyed. Component specific measurements are necessary to protect the workers from exposure while avoiding unnecessary interruptions to the printing process from false alarms.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for fumigation

    Sea cargo containers and wooden packing materials are fumigated to control the spreading of pest animals and micro-organisms. Fumigant gases are toxic and measurements are carried out as a health and safety precaution. Measurements are required by e.g. customs inspectors prior to opening containers, making the shipping companies responsible for carrying out measurements. Products shipped in containers may release VOCs from e.g. solvents and glues used in manufacturing process. The concentrations of vapors may be significant in the confined space of the container. While most containers originate in China and Southeast Asia, cargo container measurements are done in ports across the world, as the same gases are encountered in all ports.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for semiconductor manufacturing

    In the semiconductor manufacturing industry, various perfluorinated compounds (PFCs) are used. The emissions of the PFC compounds into the ambient air are reduced by scrubbing of the exhaust gases from the process. In this process, the Gasmet™ FTIR Gas Analyzers can be used to measure the emissions into the atmosphere and also monitor the efficiency of the scrubbers. Typically monitored PFCs in the exhaust gas include carbon tetrafluoride CF4, trifluoromethane CHF3, and hexafluoroethane C2F6.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for stack testing according to EPA test method 320

    The United States Environmental Protection Agency (EPA) has two stack testing methods for FTIR gas analyzers. Method 320 is an FTIR method for measuring wide range of organic and inorganic pollutants. Method 321 is a specific version for measuring hydrogen chloride HCl at cement kilns producing Portland cement. These methods define a quality assurance and control processes for verifying the accuracy of the results. The requirements for analytical equipment and software are defined on 40 CFR Part 60 Appendix B Performance Specification 15. Gasmet™ Gas Analyzers and Calcmet™ software have been designed to take the requirements of the performance specification into account.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Environmental monitoring solution for mineral processing

    Measurement of particulates, SO2, NOX, CO, hydrocarbons and greenhouse gas emissions from the mineral process industries requires careful selection of instrumentation. Ecotech offers a complete monitoring solution tailored to this industry.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Premium

    Process Control for the Petrochemical Chemical Industry

    Most chemical products as we know today are composed of a few hundreds of basic chemicals, extracted mostly from crude oil and natural gas. Instrumentation, analyzer systems and process optimization are not new to the operation of all chemical and petrochemical processes.

    However, tightening regulations, competition pressure and increasing raw materials cost urges the industry to go deeper into process control technology. As a single-source supplier of the (petro)chemical industry since many years, AppliTek has supplied them many analyzer systems for monitoring chemical parameters in all sorts of applications, from the actual production step to peripheral treatment processes. Our application people and engineering department understand your needs and translate them into real solutions.

    By AppliTek NV based in Nazareth, BELGIUM.

  • Premium

    Flow measurement instrumentation for waste water treatment flow solutions

    With its high turndown and direct mass flow, our immersible thermal meters are the instrument of choice for measuring aeration basin air flow and monitoring digester gas. Our vortex meters are used to measure steam in the cogeneration processes, while our ultrasonic flowmeters are used for influent and effluent measurement.

    By Sierra Instruments, Inc. based in Monterey, CALIFORNIA (USA).

  • Premium

    Measurement solution for VOC emissions monitoring

    Protea has used our VOC gas analysers in many projects requiring the monitoring of complex mixes of VOCs. In the chemical and pharmaceutical industry, VOC abatement plants such as scrubbers and carbon-bed systems are typical installations where the use of Protea analysers and our VOC analysis expertise have proved valuable to plant operators. They prove a very powerful and flexible tool in both process gas measurements and VOC emissions monitoring. In the laboratory, Protea can deliver instruments with all the chemometric software and support to enable users to measure hundreds of gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Measurement solution for organic vapour speciation

    Protea has deployed FTIR gas analysers in many projects requiring the monitoring of complex mixes of VOCs. In the chemical and pharmaceutical industry, scrubbers and carbon-bed abatement plants are typical installations where the use of Protea FTIR analysers and our chemometric expertise have proved valuable to plant operators. They prove an invaluable tool in process measurements and emissions monitoring. In the laboratory, Protea can deliver instruments with all the chemometric software and support to enable users to measure hundreds of gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Chemical Industry Emissions Analysis

    The inherent flexibility of Procal analysers enables the instruments to be configured to meet Customer’s specific requirements. Their capability to monitor gas concentrations at elevated pressures and temperatures make Procal products ideal for process applications in the Chemical Industry.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Biogas Monitoring for the Renewable Energy Industry

    AppliTek`s solutions in this field concentrate on the process efficiency of anaerobic digesters. Many existing digesters give unnecessary problems, which arise due to inadequacies in the process or process control system. AppliTek has developed a unique instrument to measure and control the key processes in the anaerobic fermentation. Compact gas analyzers with proprietary technology can be implemented to check the biogas yield.

    Parameters: Volatile Fatty Acids - Alkalinity - pH - Bicarbonate

    Gas parameters: CH4 - CO2 - O2 - H2S

    By AppliTek NV based in Nazareth, BELGIUM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you