Only show results available in Virginia? Ok

sludge conditioning Applications

  • Enhanced Biosolids and Bio Sludge Dewatering with Wilsa EWC

    IMPROVED BIOSOLIDS/ BIO SLUDGE DEWATERING WITH WILSA® CONDITIONING The WILSA ElectroWave™ effect can be used to condition polar fluids to alter their physical properties, improving several chemical and physical processes. - Reducing surface tension to improve the ability of water to repel solids - break physical / chemical emulsions - Increasing the contact angle of water - improve coalescing of solid particulate toaccelerate phase separation - Lowering the viscosity of water - reduce friction of flocculated solids dropping through less viscous water - Lower viscosity, reduced surface tension and increased contact angle of water - improve aeration of wastewater Installation of WILSA® ElectroWave Conditioner upstream of a belt press at a wastewater treatment plant resulted in polymer usage dropping by >50% while achieving much dryer solids.

    By Hudson Industries based in Vienna, OHIO (USA).

  • Premium

    Treatment, Optimization and Design for WWTP's

    The purpose of the work is to demonstrate the rationale, procedures and advantages of using process simulation to evaluate the steps involved in process upgrades from conventional or fully aerobic process conditions to multi stage systems capable of operating as a BNR system. In the author's experience and the conclusions of this presentation are that the use of these systems in daily operations and in the preparation for process upgrading is empowering and economically advantageous. SASSPRO(Steady State Activated Sludge Simulator, Program)

    By WeDoTanks.com LLC based in Sahuarita, ARIZONA (USA).

  • Belt filter press

    Belt Filter Press is often applied in wastewater treatment plant sludge dewatering process and it is one of the most cost effective options regardless of the type of sludge feed into the systems. There are several combined processes added into one unit and it involves different applications such as chemical conditioning, gravity drainage and mechanical shearing and compression effect to remove water and dry up the sludge. Today, belt filter presses are widely used and it has become a standard for general wastewater sludge application and thus, learning how to optimize and use it to your advantage is very important.

    By Henan Jincheng Filter Equipment Co., Ltd based in Yuzhou city Henan province, CHINA.

  • Headworks Odor and Corrosion Control Using Hydrogen Peroxide

    Hydrogen Peroxide typically controls odors and corrosion at treatment plant headworks by direct oxidation of hydrogen sulfide (H2S) within the wastewater. In the direct oxidation mode, H2O2 is applied to the wastewater 5-30 minutes prior to the point where the odors are being released, generally as the wastewater line enters the plant boundary. The efficiency of hydrogen peroxide treatment depends upon the available reaction time, the level of iron in the wastewater (reaction catalyst), wastewater pH and temperature, and the initial and target levels of H2S odor. Under optimal conditions, effective dose ratios are 1.2 - 1.5 parts H2O2 per part dissolved sulfide, and can be reliably estimated through beaker tests. H2O2 + H2S → S0 + 2H2O Frequently, control of odors through the primary clarifiers is wanted. In such case, the mechanism of control is both direct oxidation of H2S (as it rises from the solids blanket), and prevention of odor generation (by supplying dissolved oxygen). Control is typically achieved with a booster dose of 1-2 mg/L H2O2 added to the clarifier influent. Higher doses or alternate modes of addition may be required in cases where: 1) hydraulic retention times are > 2-3 hours; 2) solids blanket depths are > 1-2 feet; 3) soluble BOD levels are > 200-300 mg/L; or 4) waste activated sludge is co-settled with the primary solids. 2H2O2 → O2 + 2H2O

    By USP Technologies based in Atlanta, GEORGIA (US) (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you