stack emissions Applications available in Mozambique

  • Premium

    Stack emissions monitoring

    Monitoring stack emissions is a fundamental requirement for most industrial processes. Our gas analysers, dust monitors and flow monitors are designed for a wide range of applications and can operate as a fully integrated system or as stand alone instruments.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Premium

    Industrial stack emission TOC monitoring

    By Pollution Srl based in Budrio (Bologna), ITALY.

  • Premium

    Determination of TOC in stack

    PROBLEM: The industrial chimney's emissions of Volatile Organic Compounds (VOCs) are becoming issues of global importance and to have an accurate knowledge about how to test VOC turns into a strategic issue. VOC emissions are quantified and monitored according to standard EN 12619, using FID analyser which uses hydrogen and other reference gases in pressurized cylinder. Operators must then approach the sampling point, often placed several meters from the ground, climbing chimneys of industrial settlements with instruments and cylinders. Is it possible making this job easier and safer? SOLUTION: Using the Polaris FID analyser produced by Pollution Srl, Italy, it is possible to carry out the VOCs monitoring according to EN 12619 without lifting accessories and heavy weights typically involved with FID analyser. Polaris FID analyser complies with this standard regulation but what is really a breakthrough and cutting-edge, is the unmatched portability and the next generation technology

    By Pollution Srl based in Budrio (Bologna), ITALY.

  • Portable Stack Monitoring

    Many industries are required to measure stack emissions of toxic gases periodically, but not continuously. Extractive wet chemical methods currently used are slow, labor intensive and expensive. A single GasFinderFC can perform stack monitoring requirements for a specific gas, quickly, easily and accurately.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Emissions Monitoring for Steel Mills

    Steel mills include a multitude of activities that generate gaseous emissions. Besides continuous emissions stack monitoring, the applications in a steel mill also include process mesaurements that provides important data to the operators in order to optimize the steel making process.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Incineration Industry Emissions Monitoring & Analysis

    Monitoring of emissions from incinerators is a demanding application for Continuous Emission Monitoring Systems. The emissions produced are highly corrosive, some of the gases are soluble and, because the waste being burnt is constantly changing, the resulting stack gas temperature varies widely.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Fugitive emissions monitoring on industrial sites

    The real-time monitoring of odorous gases or more classical pollutants emitted by industrial sites (wastewater treatment plants, refineries, landfills, etc.) appears nowadays as a requirement, in order to optimize the site process and operations, or communicate towards the neighborhoods and local public bodies. While emissions can be measured directly at the source (in the stack, exhaust, etc.), ambient air measurement all around the sites provides a better accuracy and anticipate pollution episodes. This is why Cairpol developed around its Cairsens sensors a concept of smart and autonomous stations: Cairnet. Without any maintenance nor calibration, Cairnet is a completely autonomous system energy-wised, with user friendly and efficient interface, accessible from any internet-connected device.

    By Cairpol Environnement S.A based in Poissy CEDEX 4, FRANCE.

  • Particulate monitoring for continuous emissions

    With the advent of specific process emission limits being defined, continuous particulate monitoring has become a regulatory requirement for many industries. smoke stack #1Particulate monitoring requires the measurement of the mass concentration of particulate matter in stack emissions to atmosphere. There is no known method of continuously measuring particulate concentration by direct measurement and therefore, all continuous particulate measurement methods are inferential. Each method involves the measurement of a parameter related to particulate concentration and then requires a calibration to be determined to convert the measured value into one of particulate mass concentration.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore, emission limits were expressed in terms of colour or opacity. Modern methods for opacity measurement still use the darkness of the stack gases to measure the amount of smoke or dust emitted within the exhaust gases.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Premium

    Process instrumentation and analytics solutions for environmental monitoring industry

    From monitoring impurities in vents, stacks, air or water to point source or area monitoring, automatic and on-line measurement is an important tool. This type of measurement will detect, quantify and assist in reducing emissions. Siemens analytical products are utilized for many of these measurements.

    By Siemens Industry, Inc. - Process Analytics based in Houston, TEXAS (USA).

  • Premium

    Monitoring solutions for the flow monitoring areas

    Many large combustion plants are now required to monitor mass emissions of major pollutants and to do so requires an accurate measurement of stack gas velocity. The VCEM 5100 is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It has several key advantages, firstly the sensors optics are not in contact with the hot and dusty environment, the VCEM 5100 can monitor gases at temperatures exceeding 10000C and the analyser requires minimal maintenance. The VCEM 5100 can be used in extremely dust environments such as SCR’s when dust loadings exceed 10g/m3. The VCEM 5100 is in full compliance with EN/ISO 16911 part 2.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Gas Detection Solutions for Carbon Fiber Manufacturing Industry

    The carbon fiber manufacturing industry requires a unique process control solution that conventional gas detection technology lacks. Boreal Laser’s line-of-sight laser based gas detection system is the perfect fit for measuring HF in various pan oven applications and stack emissions monitoring . Whether you are looking for gas detection solutions for safety, environmental or process control needs Boreal Laser has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you