Only show results available in Virginia? Ok

stack gas Applications

  • Premium

    Stack emissions monitoring

    Monitoring stack emissions is a fundamental requirement for most industrial processes. Our gas analysers, dust monitors and flow monitors are designed for a wide range of applications and can operate as a fully integrated system or as stand alone instruments.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Stack gas analysis for power plants

    By Instrumatic A/S based in Ry, DENMARK.

  • Premium

    Portable Stack Monitoring

    Many industries are required to measure stack emissions of toxic gases periodically, but not continuously. Extractive wet chemical methods currently used are slow, labor intensive and expensive. A single GasFinderFC can perform stack monitoring requirements for a specific gas, quickly, easily and accurately.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Premium

    Gas monitoring instruments and systems for stack testing according to EPA test method 320

    The United States Environmental Protection Agency (EPA) has two stack testing methods for FTIR gas analyzers. Method 320 is an FTIR method for measuring wide range of organic and inorganic pollutants. Method 321 is a specific version for measuring hydrogen chloride HCl at cement kilns producing Portland cement. These methods define a quality assurance and control processes for verifying the accuracy of the results. The requirements for analytical equipment and software are defined on 40 CFR Part 60 Appendix B Performance Specification 15. Gasmet™ Gas Analyzers and Calcmet™ software have been designed to take the requirements of the performance specification into account.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Odor control for refining/petroleum

    You refine the fuel, we’ll remove the odors. Oil refineries and petrochemical plants may generate large volumes of odor from the processing and refining of different fuels. Sulfides, mercaptans, and hydrocarbon compounds are all closely related to the oil industry. The odors generated from these industrial compounds are of a high nuisance value and generally create concern among local air boards and the public. Ecosorb odor removal products may be used in a variety of areas around the refinery including water treatment facilities, sludge ponds, sulfur recovery units, and API separators. To remove odors during tank cleaning and maintenance operations, portable dispersion systems can be used in the immediate work area to control malodors. Ecosorb products can be directly injected into flues and stacks and may be used as a substitute scrubbing solution in some applications.

    By OMI Industries (OMI) based in Long Grove, ILLINOIS (USA).

  • Premium

    Gas Detection Solutions for Carbon Fiber Manufacturing Industry

    The carbon fiber manufacturing industry requires a unique process control solution that conventional gas detection technology lacks. Boreal Laser’s line-of-sight laser based gas detection system is the perfect fit for measuring HF in various pan oven applications and stack emissions monitoring . Whether you are looking for gas detection solutions for safety, environmental or process control needs Boreal Laser has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Premium

    Gas Detection Solutions for Power Generation Industry

    Boreal possess an array of products for the power generation industry from emissions stack monitoring, boiler room monitoring, chloride leak detection, and ammonia slip in deNOX. Boreal’s products are tailor made for coal fired power plants, natural gas fired, and waste-to-energy. Whether gas detection is used for safety, process, or environmental reasons, Boreal has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Integrated real-time gas analysis solution for emissions industry

    Pollutant emissions from industrial smoke stacks are a major national concern due to both health concerns and climate change. As a consequence, there are at least tens of gas analyzer manufacturers in the U.S. alone that compete in that market and have done so for years. What CIC Photonics brings to that competitive field is its expertise derived from its Combustion Efficiency Solution and its high performance IRGAS Systems. The IRGAS-CEM provides real-time and simultaneous measurements of the multitude of toxic combustion products, including CO, CO2, NOx, SOx, CH4, CxHy, H2S, etc. The EP-IRGAS-SPA is also applicable for fast time responses.

    By CIC Photonics, Inc. based in Albuquerque, NEW MEXICO (USA).

  • Premium

    High quality gas sensor solutions for landfill

    State-of-the-art systems enabling easy monitoring of CO2 and CH4 gases. Capped Landfill Sites produce a range of gases, mostly methane and carbon dioxide. Legislation requires that these gases are safely removed from beneath the cap to avoid a physical explosion due to the build-up of pressure beneath the cap. Safe disposal usually entails burning such as flare stacks, internal combustion engines or by processing to produce Methane gas fuel. For large sites with access to power distribution infrastructure internal combustion engines are used to generate electricity which is fed into the local electricity grid. All of the above safe disposal process require the measurement of the Methane content (and in many cases the CO2 concentration). Edinburgh Sensors provide gas sensors for both Methane and CO2 that can be integrated into landfill gas processing systems enabling easy monitoring of these gases.

    By Edinburgh Instruments Ltd based in Livingston, UNITED KINGDOM.

  • Gas detection analyzers for pollution control

    Government and environmental groups are forcing industries with medium to high VOC exhausts to reduce emissions by as much as 98%. Incineration using pollution control devices such as oxidizers and flare stacks is one way to bring the exhaust emissions in line with the regulations. Capturing and reusing solvent in a solvent recovery system is another way.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Incineration Industry Emissions Monitoring & Analysis

    Monitoring of emissions from incinerators is a demanding application for Continuous Emission Monitoring Systems. The emissions produced are highly corrosive, some of the gases are soluble and, because the waste being burnt is constantly changing, the resulting stack gas temperature varies widely.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Environmental technology for droplet seperation industry

    As component of the gas scrubbing plants or as single apparatus Körting swirl droplet separators for seperating droplets and recondensates make an essential contribution towards the observation of emission codes and therefore towards the protection of the environment. They are used in gas scrubbing and vacuum plants, for condensate separation in chimney stacks, in evaporating plants as well as for the separation of difficult products (e. g. those with a tendency to polymerisation).

    By Körting Hannover AG based in Hannover, GERMANY.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you