Only show results available in Virginia? Ok

stack gas emissions monitoring Applications

  • Premium

    Stack emissions monitoring

    Monitoring stack emissions is a fundamental requirement for most industrial processes. Our gas analysers, dust monitors and flow monitors are designed for a wide range of applications and can operate as a fully integrated system or as stand alone instruments.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Portable Stack Monitoring

    Many industries are required to measure stack emissions of toxic gases periodically, but not continuously. Extractive wet chemical methods currently used are slow, labor intensive and expensive. A single GasFinderFC can perform stack monitoring requirements for a specific gas, quickly, easily and accurately.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Continuous Emissions Monitoring

    Requirements for monitoring emissions to air are governed by EU/UK legislation and are implemented in the form of a permit by the Environment Agency or local authority. The Dr Foedisch muti-component gas analysers continuously extract a gas sample from the exhaust stream via a stack probe into the analyser cabinet. Both hot and cold gas systems are available, please contact us to discuss which system best suits your requirements.

    By CEM Solutions (UK) Ltd. based in Darley Dale, UNITED KINGDOM.

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Incineration Industry Emissions Monitoring & Analysis

    Monitoring of emissions from incinerators is a demanding application for Continuous Emission Monitoring Systems. The emissions produced are highly corrosive, some of the gases are soluble and, because the waste being burnt is constantly changing, the resulting stack gas temperature varies widely.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Monitoring solutions for the flow monitoring areas

    Many large combustion plants are now required to monitor mass emissions of major pollutants and to do so requires an accurate measurement of stack gas velocity. The VCEM 5100 is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It has several key advantages, firstly the sensors optics are not in contact with the hot and dusty environment, the VCEM 5100 can monitor gases at temperatures exceeding 10000C and the analyser requires minimal maintenance. The VCEM 5100 can be used in extremely dust environments such as SCR’s when dust loadings exceed 10g/m3. The VCEM 5100 is in full compliance with EN/ISO 16911 part 2.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Gas Detection Solutions for Carbon Fiber Manufacturing Industry

    The carbon fiber manufacturing industry requires a unique process control solution that conventional gas detection technology lacks. Boreal Laser’s line-of-sight laser based gas detection system is the perfect fit for measuring HF in various pan oven applications and stack emissions monitoring . Whether you are looking for gas detection solutions for safety, environmental or process control needs Boreal Laser has you covered.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you