Only show results available in Virginia? Ok

stack test Applications

  • Stack Testing for Rod Mill Exhaust Stack

    STEEL INDUSTRY: Conducted particulate testing and continuous emission monitoring of a rod mill exhaust stack. In addition, testing was performed to determine emissions associated with a slow cooling pen associated with ball mill production.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Premium

    Determination of TOC in stack

    PROBLEM: The industrial chimney's emissions of Volatile Organic Compounds (VOCs) are becoming issues of global importance and to have an accurate knowledge about how to test VOC turns into a strategic issue. VOC emissions are quantified and monitored according to standard EN 12619, using FID analyser which uses hydrogen and other reference gases in pressurized cylinder. Operators must then approach the sampling point, often placed several meters from the ground, climbing chimneys of industrial settlements with instruments and cylinders. Is it possible making this job easier and safer? SOLUTION: Using the Polaris FID analyser produced by Pollution Srl, Italy, it is possible to carry out the VOCs monitoring according to EN 12619 without lifting accessories and heavy weights typically involved with FID analyser. Polaris FID analyser complies with this standard regulation but what is really a breakthrough and cutting-edge, is the unmatched portability and the next generation technology

    By Pollution Srl based in Budrio, ITALY.

  • Stack Testing for Power Generation Plants

    POWER GENERATION INDUSTRY: Conducted detailed measurements of volumetric flow, oxygen, and carbon dioxide levels in huge main ducts in the Economizer Outlet, Air Heater Inlet, and Exhaust Stack locations in order to evaluate overall plant and control system performance

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Stack Testing for the Aluminum Industry

    ALUMINUM INDUSTRY: Performed a range of test measurements required by the promulgation of the Secondary Aluminum MACT standards. Testing included measurements of Hazardous Air Pollutants for establishing Area vs. Major Source Determinations, as well as dioxin/furan compounds associated with chlorine emissions from fluxing operations.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Stack Testing for Medical Waste Industry

    INFECTIOUS WASTE INDUSTRY: Provided annual testing for metals, particulate, HCl, dioxins/furans, and typical continuous emission monitoring constituents.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Stack Testing for Sewage Sludge Incinerators

    SEWAGE TREATMENT INDUSTRY: Provided Incinerator Performance Testing Services and Relative Accuracy Testing of a Continuous Emission Monitoring system associated with sewage sludge incinerator.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Continuous Metals Stack Monitor (CEMs)

    Cooper Environmental's Xact® 640 has the unique ability to generate high time resolution metals measurement in stacks. This unique capability has the potential to qualify as a substitution for the combination of a Hg/ PM CEMs application as well as the potential for a pollution control system feedback loop that could result in the reduction of pollution control consumables. Our systems have been site certified for compliance measurements at hazardous waste incinerator and secondary lead smelter sites.

    By Cooper Environmental based in Beaverton, OREGON (USA).

  • Stack Testing for Cement Production Facility

    LIMESTONE AND CEMENT PRODUCTION INDUSTRY: Conducted a facility-wide evaluation and NSPS performance test program of a major limestone and portland cement production facility.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Stack Testing for VOC Recovery Afterburner Installation

    HAZARDOUS WASTE HANDLING INDUSTRY: Conducted on-site GC speciation of VOC constituents by Method 18 collecting samples continuously around-the-clock in large vacuum canisters in order to demonstrate compliance control of a VOC recovery/afterburner installation

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Stack Testing for Cement Kilns

    CEMENT INDUSTRY: Performed RCRA Trial Burn and Comprehensive Performance Test Programs for multiple kilns firing hazardous waste fuels.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Premium

    Gas monitoring instruments and systems for stack testing according to EPA test method 320

    The United States Environmental Protection Agency (EPA) has two stack testing methods for FTIR gas analyzers. Method 320 is an FTIR method for measuring wide range of organic and inorganic pollutants. Method 321 is a specific version for measuring hydrogen chloride HCl at cement kilns producing Portland cement. These methods define a quality assurance and control processes for verifying the accuracy of the results. The requirements for analytical equipment and software are defined on 40 CFR Part 60 Appendix B Performance Specification 15. Gasmet™ Gas Analyzers and Calcmet™ software have been designed to take the requirements of the performance specification into account.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Emissions testing for industrial boilers and burners

    Industrial boilers and burners have their own unique characteristics. When an unexpectedly high CO is detected, the Testo 350 will automatically adjust to the situation, keeping the sensor protected at all times. Don`t worry about climbing and removing the probe from the stack, just hit the fresh air button. The measurements of O2, CO, NO and SO2, combined with automatic calculations (CO2, efficiency, excess air), provide fast tuning solutions. The 350`s compact design is better for working on a platform or small space. The automatic zero pressure measurement is ideal to monitor flow or draft induction. With a pitot tube you can quickly measure velocity and determine mass flow even during long term testing. The Testo 350 makes reporting in lbs/hour easy!

    By Testo Inc. based in Sparta, NEW JERSEY (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you