Only show results available in Virginia? Ok

used oil analysis Applications

  • Premium

    Oil on Metals Analysis

    Got oil on metal? Need to test parts for oil residue to ensure the parts are clean and oil free? Sitelab's analyzers are easy to use or send samples to Sitelab for laboratory analysis. Samples are extracted in solvent using test kits available. Wipe samples can also be tested.

    By Sitelab Corporation based in West Newbury, MASSACHUSETTS (USA).

  • Premium

    NAPL Fingerprinting Analysis

    Sitelab's mobile laboratory was used by a client at a former oil refinery in Kansas and at a large tank farm in Massachusetts. The UVF data was used to delineate and map subsurface plumes of NAPL. Oil samples were collected from monitoring wells and analyzed for their GRO/DRO or VPH/EPH content.

    By Sitelab Corporation based in West Newbury, MASSACHUSETTS (USA).

  • Premium

    Oil in Water Analysis for Flowback or Produced Water

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water. Waiting for remote lab results can take several days to a week. InfraCal TOG/TPH Analyzers allow for oil in water testing at the well site in less than 10 minutes. The sampling requires a few simple steps that can be performed by non-technical personnel. The water is mixed with the extraction solvent, shaken, and then presented to the analyze for measurement. The same InfraCal TOG/TPH Analyzer can be used for TPH in soil if a spill or pond leak occurs to determine the contaminated area. The analyzer features: -Results in under 15 minutes -Detect levels as low as 10 ppm -Portable, rugged, lightweight, easy-to-use -Battery operable -Ideal for field or lab use

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • Premium

    Measurement of C1-C5 hydrocarbons for oil & gas exploration.

    The PetroAlert Model 8900 combines the selectivity of gas chromatography with the sensitivity, broad dynamic range, and hydrocarbon selectivity of a flame ionization detector (FID) providing fast analysis of C1-C5 hydrocarbons required in Mud Logging for Oil & Gas exploration. The PetroAlert Model 8900 uses a dual column configuration with timed backflush to vent which is used to strip off moisture and C6+ hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed sample volume is carried to the pre-cut column. Backflush of the pre-cut column is timed from sample injection so that only C1-C5 hydrocarbons are eluted from the pre-cut column to the analytical column. C6+ hydrocarbons on the pre-cut column are then vented. C1-C5 hydrocarbons are separated on the analytical column and elute to the flame ionization detector (FID) for analysis.

    By MOCON, Inc. - Baseline based in Lyons, COLORADO (USA).

  • Active Refinery Remediation

    Waste Management Unit (WMU) closures at this active refinery Waste Management Unit (WMU) closures at this active refinery - Installation of several soil, Liquid Boot, and full multi-layer geocomposite cover systems in various facility locations- - Sensitive construction practices including large scale activities near power lines, 30 inch raw water line, and several active emergency flares - Completed performance based in-situ solidification/stabilization, cap and closure, using ENTACT owned large diameter auger Delmag rig and custom-fabricated Geodrill - COC`s include heavy metals, PAH, volatile organic compounds, and petroleum hydrocarbons Performance criteria include an unconfined compressive strength of 10 psi, permeability coefficient of less than 2.1x10-6 cm/sec, and an admixture pH of less than 11.5 - ENTACT performed in-house treatability analysis to develop reagent admixture

    By ENTACT, LLC based in Grapevine, TEXAS (USA).

  • Premium

    Measurement of C1-C5 with carbon dioxide for oil & gas exploration.

    The PetroAlert Model 8900 combines the selectivity of gas chromatography with the sensitivity, broad dynamic range, and hydrocarbon selectivity of a flame ionization detector (FID) providing fast analysis of C1-C5 hydrocarbons and Carbon Dioxide required in Mud Logging for Oil & Gas exploration. The PetroAlert Model 8900 uses a dual column configuration with timed backflush to vent which is used to strip off moisture and C6+ hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed sample volume is carried to the pre-cut column. Backflush of the pre-cut column is timed from sample injection so that only C1-C5 hydrocarbons are eluted from the pre-cut column to the analytical column. C6+ hydrocarbons on the pre-cut column are then vented. Then a third column is used in conjunction with a second 10-port valve for individual analysis of methane. C1-C5 hydrocarbons are separated on the analytical column and elute to the flame ionization detector (FID) for analysis.

    By MOCON, Inc. - Baseline based in Lyons, COLORADO (USA).

  • Premium

    Produced Water Analysis

    Sitelab's UVF-3100D is used to test crude oil in water collected from produced water treatment sites in Wyoming. Water was tested for it's GRO and DRO content.

    By Sitelab Corporation based in West Newbury, MASSACHUSETTS (USA).

  • Premium

    Measurement of acetaldehyde, methanol, & benzene in CO2 applications for gas manufacturers & food & beverage industry

    The BevAlert Model 8900 provides direct measurement of Acetaldehyde, Methanol, and Benzene (AMB) in Carbon Dioxide. The instrument is utilized by Specialty Gas Manufacturers and the Food and Beverage Industry to monitor trace impurities in CO2 used in carbonated beverages. The BevAlert Model 8900 employs a photoionization detector (PID). The AMB in the gas sample are physically separated using proprietary GC columns. A dual-column configuration with timed backflush to vent is used to strip off moisture and heavier gases. At sample injection, a fixed volume of sample is carried through the pre-cut column. The backflush is timed so that primarily the AMB and other similar compounds continue on to the analytical column. Contaminants are then backflushed to vent. Acetaldehyde, Methanol, and Benzene are separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By MOCON, Inc. - Baseline based in Lyons, COLORADO (USA).

  • calibration gas

    calibration gas , British specialty gases company, with a local North Africa presence. We can supply you with high quality gas mixtures for a wide range of applications including Environmental Monitoring, Gas Detection, Mud Logging, Laser Cutting, and Laboratory Analysis. Our gas mixtures are used in the Oil, Gas and Petrochemical industries Our main focus is to give our customers gravimetrically produced, high precision calibration gas mixtures conforming to ISO 6142, along with a range of high purity gases and pressure control equipment, used for instrumental analysis and gas detection applications. AG Gases' senior management have many years experience in the European and International markets and now offer this knowledge to benefit Egyptian and North African customers.

    By AG Gases Ltd based in Stoke-on-Trent, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you