Only show results available in Virginia? Ok

waste acceptance Applications

  • Rugged Mobile Technology for Waste Management

    Waste management is another market for which it isn`t too hard to see why ruggedness is essential. Dirty, wet, dusty conditions are an accepted part of each day in the field. Tracking carts, recording data on routes, and GPS navigation are just a few of the areas where rugged mobile computers can help get the job done easier, faster and better.

    By Handheld UK and Ireland Ltd based in Leamington Spa, UNITED KINGDOM.

  • Refuse Derived Fuel (RDF) & Solid Recovered Fuel (SRF)

    A full-scale Gasplasma® plant can make its own RDF from MSW/Commercial Waste. The waste is brought directly into a fuel preparation hall at the front of the building. Inside the fuel preparation hall there is industry standard equipment that can recover glass, metals and hard plastics from the wastes for recycling. The remaining waste is then dried and shredded to make a Refuse Derived Fuel (RDF) for the Gasplasma® energy from waste process. Clients who already produce RDF may not require a fuel preparation hall. APP can design a plant without this facility, accepting the RDF directly from the client. Secondary Recovered Fuel or Solid Recovered Fuel (SRF) is often confused with Refuse Derived Fuel because they are similar in nature. However, SRF is produced to reach a clearly defined standard such as CEN/343 ANAS whereas RDF is not.

    By Advanced Plasma Power (APP) based in Swindon, UNITED KINGDOM.

  • Premium

    Applications and Air Pollutants Removed in the Biomass Industry

    Flue gas particulate and acid gases from biomass and bagasse boilers. Removal of ethanol, CO2 scrubbers and yeast cells from fermenters.  Removal of ash particulate, tars, acid gases and ammonia from steam reformers, gasifiers, pyrolosis units and cooling of syngas streams to acceptable limits to enable use as a fuel source for power generation or as a feedstock for chemical products. For tar removal, combination technologies can be used including oil based scrubbing solutions to reduce waste water generation. Ethanol and yeast cell removal from fermenter off-gases. Methanol from processing operations. Hydrogen sulfide removal on landfill, digester and producer gases with regenerable chemistries. Odor control for biomass storage facilities including carbon monoxide removal in wood chip storage areas. 

    By Bionomic Industries Inc. based in Mahwah, NEW JERSEY (USA).

  • Premium

    Wastewater treatment for the metal industry

    Wastewater and process water treatment in the metal industry. Industrial waste water or circuit water in the metal industry can be broken down into many comprehensive, subject-specific areas. AWAS has developed various methods of treatment technology for the metal industry in the last 30 years. Generally we accept any environmental challenge and like to respond to individual problems.

    By AWAS International GmbH based in Wilnsdorf, GERMANY.

  • metal scrap recycling

    metal scrap recycling is suitable for the steel plants,recycling companies ferrous non-ferrous metal smelting industry to compress metal scrap(steel paring,waste copper & aluminum, waste stainless steel, scrap from discarded automobiles)into acceptable furnace charges of cuboids, cylinders, octagons & other shapes, so as to reduce the cost of transportation & smelting, to speed up furnace charging.

  • Systems for the EPS foam processors industry

    Without an effective processing strategy, foam waste can easily overrun your valuable floor space. And depending on the volume and variety you accept, a simple compression solution might not be enough. Do you need a dedicated densifier for each grade? Is an air conveyance system right for your operation? OBC has years of experience analyzing and prescribing equipment configurations for effective foam processing solutions.

    By OBC Baling Equipment based in Cleveland, OHIO (USA).

  • Biological wastewater processes for mining

    The mining industry has the potential to use large amounts of wastewater in its operations. Often times these waste streams contain contaminants that require treatment before the water can be re-used or discharged. Biowater has successfully installed highly efficient biofilm treatment processes including our complete mix fixed film (CMFF®) system to remove BOD/COD, and nitrogen from mining waste streams. Biowater’s technologies, such as our CFIC® process, can produce effluent water quality that is acceptable for re-use, reducing the stress on ecosystems in water stressed areas.

    By Biowater Technology based in Cumberland, RHODE ISLAND (USA).

  • Solutions for recovering metals

    The mining industry relies on Calgon Carbon’s Granular Activated Carbon (GAC) to recover gold and other precious metals. Calgon Carbon’s ISEP® Technology is used to recover precious, rare earth and base metals, uranium, copper, nickel and zinc from ore, waste and reclaim streams. Our high-quality activated carbons have been developed and successfully proven to maximize efficiency by reducing the loss of precious metals and the consumption of carbon in three precious metal extraction techniques: Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP) and Carbon-in-Column (CIC). When Ion Exchange is employed for metal recovery in leach and waste streams, Calgon Carbon’s ISEP ® system provides a continuous, consistent and high purity concentrated product while minimizing the use of chemicals, resin and wastes. Calgon Carbon’s continuous ion exchange systems are the most flexible, robust, and accepted in the industry.

    By Calgon Carbon Corporation based in Pittsburgh, PENNSYLVANIA (USA).

  • Scrap Metal Baler

    1. Product Name: Y83-250 Scrap Metal Baler For Sale 2. Application: Y83-2500 Scrap Metal Baler For Sale is suitable for the steel plants, recycling companies, ferrous & non-ferrous metal smelting industry to compress metal scrap(steel parings, waste steel, waste copper & aluminum, waste stainless steel, scrap from discarded automobiles) into acceptable furnace charges of cuboids, cylinders, octagons & other shapes, so as to reduce the cost of transportation & smelting, to speed up furnace charging. 3. Metal Baler Specifications: Nominal force (kN):2500 Dimension of compress room (L*W*H) (mm):2000*1400*900 Bale dimension (L*W*H)(mm):(400-700)*450*450 Bale density (kg/m3 ):>1800 Capacity (kg/h):3500-4500 Single cycle time(s):<160 Power (kW):60 Bale discharging and operation:Turn-out, hand valve control 4. Quality: This metal baler apply to ISO9001: 2000 standard. 5. Service: 1) One year guarantee and lifelong maintenance; 2) Any problem, you can call us directly.

    By Jiangsu Wanshida Hydraulic Machinery Company based in Jiangyin, CHINA.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you