Water Analysis Applications on Environmental XPRT

Premium

Mercury analysis for wastewater

By Analytik Jena AG based in Jena, GERMANY.

Water analysis for the agriculture industry

By Advanced Technical Services GmbH based in Zug, SWITZERLAND.

Environmental Water Analysis

Now for the first time you can measure ion levels in drinking / tap water, rivers and lakes using one probe and one set of calibration solutions. We have probes specially tailored for environmental testing. Our Environmental probes measure Chloride, Ammonium and Nitrogen or we have a total nitrogen probe measuring Ammonium and Nitrogen. Each probe can be calibrated in our unique calibration solutions allowing you to calibrate all sensors simultaneously and take measurements in drinking or river water. Probes are also available in our standard four or six ion combinations and can be custom packaged upon request.

By CleanGrow based in Blackpool, IRELAND.

Premium

Bromate analysis for the drinking water industry

Bromate forms during the ozonization of drinking water. Several international standards stipulate detection limits and test methods. Conductivity detection with chemical suppression allows the determination of bromate in the lower μg/L range. In the ng/L range, bromate can be detected by IC/MS coupling or post-column derivatization with potassium iodide and subsequent UV detection.

By Metrohm AG based in Herisau, SWITZERLAND.

Analysis of Herbicides in Drinking Water

Herbicides are used throughout the world to combat the growth of unwanted plant life. These polar compounds are hydrophilic, so they may find their way into drinking water sources. While gas chromatography has historically been the preferred technique for analysis of herbicides in water samples, the use of LC-MS/MS for this application is gaining acceptance. This is due to the power of MS/MS to provide detailed identification of multiple analytes, but also in part due to the variety of HPLC stationary phases that are available. In particular, several HPLC phases are available that provide great retention and peak shapes for polar analytes, such as herbicides, even under mostly aqueous mobile phase conditions. The combination of these factors may possibly eliminate need for time-consuming sample preparation.

By MilliporeSigma based in Bellefonte, PENNSYLVANIA (USA).

Drinking water analysis for municipalities

GE Analytical Instruments offers several Sievers TOC Analyzer models designed specifically to simplify monitoring of drinking water treatment plants. Always knowing the TOC levels throughout a water treatment plant, and improving TOC reduction, can help a plant not only control DBPs, but also implement efficient and potentially cost saving treatment processes.

By GE Analytical Instruments based in Boulder, COLORADO (USA).

Premium

TOC/TNb analysis for wastewater industry

By Analytik Jena AG based in Jena, GERMANY.

Premium

Water analysis for municipal wastewater treatment

Voltammetric determination of many heavy metals is also possible in municipal or industrial wastewater. On account of the usually high organic load the sample is usually mineralized by means of UV digestion.

By Metrohm AG based in Herisau, SWITZERLAND.

Wastewater TOC Measurement and Analysis

By GE Analytical Instruments based in Boulder, COLORADO (USA).

Water analysis for the petrochemical industry

By Advanced Technical Services GmbH based in Zug, SWITZERLAND.

Premium

Gas analysis & monitoring system for water - natural sciences

In nature, the chemical elements can be represented by more isotopes, or atoms of the same element, characterized by a different number of neutrons in the nucleus. When the proton / neutron ratio does not exceed that value likely to upset the balance of the atom, resulting in the phenomenon known as stabilization of radioactive decay, the isotope is called stable. That is, over time, will not tend to emit energy and sub-nuclear particles to gain energy stability, giving rise, at the end of the process, the daughter nucleus (a different element, characterized by stability energy).

By ETG Risorse e Tecnologia S.r.l. based in Montiglio, ITALY.

Data analysis and visualization tools for surface water modelling

Volumetric modeling of surface water bodies to include mapping of properties data into the volume requires the capabilities only found in EnterVol. When trying to assess the health of a lake, river or stream, volumetric data is essential. Once you apply the capabilities of EnterVol to this task, you’ll discover trends in your data that were previously hidden or suppressed by the limitations of 2D techniques.

By C Tech Development Corporation based in Las Vegas, NEVADA (USA).

Premium

Oil in Water Analysis for Flowback or Produced Water

The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water. Waiting for remote lab results can take several days to a week. InfraCal TOG/TPH Analyzers allow for oil in water testing at the well site in less than 10 minutes. The sampling requires a few simple steps that can be performed by non-technical personnel. The water is mixed with the extraction solvent, shaken, and then presented to the analyze for measurement. The same InfraCal TOG/TPH Analyzer can be used for TPH in soil if a spill or pond leak occurs to determine the contaminated area. The analyzer features: -Results in under 15 minutes -Detect levels as low as 10 ppm -Portable, rugged, lightweight, easy-to-use -Battery operable -Ideal for field or lab use

By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

Produced Water Analysis

Sitelab's UVF-3100D is used to test crude oil in water collected from produced water treatment sites in Wyoming. Water was tested for it's GRO and DRO content.

By Sitelab Corporation based in West Newbury, MASSACHUSETTS (USA).

Premium

Test Kits and Photometric Methods for agriculture, in food or water analysis

When analyzing water and food, trust plays a very important role. Only careful analysis using tests that are performed correctly and are delivering sound results will help to maintain and improve our quality of life. With ready-to-use tests and test systems from Merck Millipore, you can trust your results. Our broad product range covers everything from water analysis to the control of production process up to the measurement of special food parameters.

By Merck based in Darmstadt, GERMANY.

Beverage Analysis

Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas/vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping and vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, & thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour & CH4 in the PPM to 100% concentration range provides vital information for process development and process monitoring

By Hiden Analytical Ltd. based in Warrington, UNITED KINGDOM.

Premium

Precision moisture analysis instruments for fast, accurate solids analysis for wastewater

Computrac moisture, solids and ash analyzers are able to quickly and easily determine solids content of cakes, slurries and sludge samples for the wastewater, hazardous waste and landfill industries. Identifying the optimal solids content of these byproducts of the treatment process can provide significant cost savings on chemical additives, haulage and incineration. Computrac analyzers are easy to use and their rugged and reliable design means that you’ll get accurate results whether they’re in the plant or in the lab. They can also be used to determine whether or not total solids content in landfills is consistent with state and local regulations.

By Arizona Instrument LLC based in Chandler, ARIZONA (USA).

Stack gas analysis for marine engines

By Instrumatic A/S based in Ry, DENMARK.

Analysis of aqueous solutions

IR-Spectroscopy is not limited to gases, solid materials and pure liquids but also facilitates the measurement of solutes in aqueous media. Though, due to the strong and temperature dependent absorption of water, the usage of conventional IR-transmission and ATR accessories is not very suitable for the analysis in water. The CONFOCHECK is a dedicated FT-IR system for the fast, easy and sensitive analysis of aqueous samples. Using this system, preparing, measuring and evaluating any aqueous sample takes typically about 1 minute.

By Bruker Corporation based in Billerica, MASSACHUSETTS (USA).

Conductivity analysis for the municipal water and waste facilities

By IC Controls Ltd. based in Orangeville, ONTARIO (CANADA).

Subscribe to our eBulletins

Add Supplier Profile