Only show results available in Virginia? Ok

water measuring system Applications

  • Water measurement systems & sensors for measuring water level & depth

    The recommended type of measurement system or water level logger system will depend on several site-specific factors such as :-

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Premium

    Water Monitoring and Flow Measurement Systems for Water Power

    Hydro power contributes to supplying approximately 3,5 per cent of electric energy generated worldwide. Its share in power generation from renewable resources lies at 18 per cent and will continue to grow as resources of fossil fuels are depleted. Hydro electric performance depends essentially on the usable altitude difference between upper and lower reservoir, and hence the resulting water flow. In order to use the “fuel” water in an optimal way, the flow velocity has to be monitored without any interruptions. Ultrasonic flow meters, flow sensors and clamp-on flow meters (OR clamp-on technology) are ideal for accurate flow metering and flow monitoring.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Water measurement systems & sensors for flow measurement

    The recommended type of measurement system will depend on several site-specific factors such as :-

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Water measurement systems & sensors for rainfall intensity logging

    ISODAQ telemetry systems are low-cost and very ease to use and configure, enabling you to bring your field data to your desktop PC without needing to operate complex IT infrastructure.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Premium

    Precipitation measurement

    From simple manual rainfall collection devices, electronic tipping bucket rain gauge sensors, through to fully autonomic stand alone data logging systems with telemetry for hydrological network applications.

    By Casella based in Kempston, UNITED KINGDOM.

  • Water measurement systems & sensors for status & condition-based monitoring

    We offer a variety of telemetry based solutions to monitor and control assets:

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Water measurement systems & sensors for water quality monitoring

    Effective water quality monitoring is the key to environmental protection of watercourses and for reliable process control and wastewater treatment.  Discharge consents under EPR regulations dictate that water quality monitoring is undertaken to ensure that consented parameters are below the consented concentrations.  Traditionally this has been done using water quality sampling methods but increasingly automatic water quality measurement sensors linked to real-time telemetry is seen as the most reliable and timely means of ensuring that treatment processes are operating efficiently and that EPR compliance is maintained.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Premium

    Water Monitoring and Flow Measurement Systems for Water Supply

    Although there is enough water on earth, its uneven distribution, the rising population and our carelessness drinking water starts to get short. In the future more and more pipelines for drinking water will be built all over the globe. In order to operate huge and complex pipe networks efficiently, water flow measurement and flow monitoring will become necessary. The increasing efficiency of ultrasonic flow meters will make such calculations more and more effective.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Premium

    Water Monitoring and Flow Measurement Systems for Hydrology

    In recent years acoustic flow measurement and flow metering has established itself as the standard method for measurement in many hydrological stations but is also used as the basis for various applications, for example for flood protection and flood forecasting. Ultrasonic flow meters are also used in hydro-engineering constructions. With this almost contact free technology data can be recorded continuously and it provides 24/7 monitoring. Such flow monitoring is particularly important in waterways used for shipping, transportation, irrigation, drainage and for cooling water extraction of power plants. A further important use of transit-time open channel flow meters is the transportation of water used for the supply of drinking water. Here the focus lies on detecting the flow rate of water loss at an early stage as it is sometimes difficult to detect small leakages.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Premium

    Power-independent flow measurement with GPRS

    In a pit water purification system it was necessary to detect the discharge volumes. The operator wanted a regular and automatic transmission of readings. On the selected measurement place no mains power connection was available. Due to the risk of vandalism, it was not planned to install a switching cabinet. See the NIVUS solution for this measurement task here.

    By NIVUS GmbH based in Eppingen, GERMANY.

  • Water measurement systems & sensors for flood warning

    Isodaq’s low-cost Isodaq telemetry data logger RTUs integrated with our telemetry data acquisition and alarm-message forwarding systems together provide the ideal solution for early warning of key events such as floods, pollution or CSO overflows.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Measurement solution for high NH3 monitoring from wastewater

    Protea was asked to supply a high level ammonia (NH3) measurement system for a waste water treatment plant. The reflux drums at the inlet to two ammonia stripping towers needed to be measured continuously. Protea designed a solution based around our Solus TDLAS analyser platform and a high level dilution system. The Solus analyser was configured for NH3 measurements in the range 0-500ppm. A dilution system incorporating special dilution probe and 19` control panel was installed before the analyser. This gave a dilution level of 600:1, enabling the NH3 analyser to measure in the range 0-30% Volume.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Water quality monitoring systems for cooling water treatment industry

    A number of treatment products are often added to prevent corrosion, scaling and fouling. Coating of sensors and other effects of these products must be taken into account when selecting analyzers. Discharge monitoring needs special attention because zero measurements must be reliable over time with little maintenance.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Premium

    Precision liquid flow sensor measurement technology

    Accurate liquid flow sensor measurement can reduce water bills, determine leakage rates, and increase system efficiency. Solve accurate water and industrial liquid flow measurement requirements with clamp-on or insertion ultrasonic flow liquid flow meters featuring precision sensing elements or our complete line of multivariable mass vortex meters.

    By Sierra Instruments, Inc. based in Monterey, CALIFORNIA (USA).

  • Premium

    Online water analysers for process water and waste water industry

    Process and waste water are the most challenging water for instrumentation. Mostly, these water are characterized by highly fluctuating loads, very high salt concentrations as well as a high particle density. Hence, the accurancy and speed of measurement depends on the measurement system itself and the used oxidation technique. Obviously, application-specific analysers provides huge advantages against standard analysers, that are used for every application.

    By LAR Process Analysers AG based in Berlin, GERMANY.

  • Premium

    Real-time Control System for Wastewater Treatment Plants

    Wastewater treatment plants (WWTP) are subject to large variation in flow and load, not to speak of uncertainties on the composition of the incoming wastewater. On top of that, the activated sludge treatment process, as used by the vast majority of treatment plants, is difficult to control due to the complex behaviour of the biological process. Nevertheless WWTPs are run 24/7, with operators and management challenged to meet ever tightening environmental regulations.

    In order to meet the operational demands of modern-day plants, a new control system was developed. Proprietary control algorithms were introduced based on a large set of data from nutrient measurements in various WWTPs. The customer`s benefits are twofold: (1) achieving optimum effuent quality and, at th same time, (2) lowering energy needs and dosing of commidity chemicals.

    By AppliTek NV based in Nazareth, BELGIUM.

  • Electrical Based Tomography Systems for Interface Detection

    Level detection is a very widespread measurement requirement. Whilst there are many techniques for detecting liquid surfaces, it is much more challenging to identify the interface between liquids and other systems.

    By Industrial Tomography Systems plc (ITS) based in Manchester, UNITED KINGDOM.

  • Sample preparation and pumping systems for wastewater treatment industry

    A wide range of sample acquisition and filtration systems are available to prepare even the most difficult of samples for reliable on-line analyser measurement. The correct choice is often critical to prevent analyser blockage and optimise performance. Cross Flow Filtration The PPM cross flow filter, is a simple in-line device used to protect an analyser from ingress of solids, for applications where sample quality is generally good but occasionally suspended solids may be present. The stainless steel filter removes solids above 50 micron size.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Electrical Based Tomography Systems for Batch mixing

    Batch mixing generally refers to mixing processes in vessels and ITS tomography instrumentation provides a tool to understand, optimise and control mixing. Tomography sensors take data from between 200 to 2,400 measurement points in a single snapshot, thus providing a sound basis to monitor changes in concentration of different materials and so quantify mixing. Sensors can be retrofitted through using probe based instruments, scanning the z-axis (which usually presents the key challenge to effective mixing). Alternatively, an array of up to 8 circular planes, each with 16 electrodes can be used to provide a more complete picture of the mixing process.

    By Industrial Tomography Systems plc (ITS) based in Manchester, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you