Only show results in Virginia? Ok

water monitoring system Applications

  • Oil in Water Monitoring

    Detection of hydrocarbons within both water sources and effluent intake to Waste Water Treatment Works is an increasing requirement. The UviLux Hydrocarbon fluorometer detects hydrocarbons in water at very low concentrations. This in-situ fluorometer provides a rugged sensor which can be deployed in a wide variety of configurations. The UviLux is part of the Lux range of CTG fluorometers, and can be provided with a number of options with regard to signal protocols, and has available accessories to enable in-flow monitoring as well as inclusion within portable systems for taking measurements in the field.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Water quality monitoring systems for portable water plants

    Low maintenance and reliability are key requirements for analyzers in potable water plants. Cost of ownership is another big issue.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Water measurement systems & sensors for status & condition-based monitoring

    We offer a variety of telemetry based solutions to monitor and control assets:

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Measurement and control systems for the Boiler water monitoring

    In ongoing operation, the substances suspended in the boiler water are concentrated. In order to avoid the negative consequences (foaming, deposits) of excessive salt content in the boiler water, specified limit values must not be exceeded. With the aid of a desalination control valve, boiler water with concentrated content is constantly removed and replaced with clean water. If the limit values are exceeded, the conductivity limitation ensures prompt switching off of the burner(s). Foreign substances that have sunk to the bottom of the boiler are removed by briefly opening a drainage valve.

    By IGEMA GmbH based in M√ľnster, GERMANY.

  • Water measurement systems & sensors for water quality monitoring

    Effective water quality monitoring is the key to environmental protection of watercourses and for reliable process control and wastewater treatment.  Discharge consents under EPR regulations dictate that water quality monitoring is undertaken to ensure that consented parameters are below the consented concentrations.  Traditionally this has been done using water quality sampling methods but increasingly automatic water quality measurement sensors linked to real-time telemetry is seen as the most reliable and timely means of ensuring that treatment processes are operating efficiently and that EPR compliance is maintained.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Premium

    Monitoring of raw water intake

    The Situation:

    Hydrocarbons in municipal water supplies,  including fresh water and desalination systems, are commonly limited to less than 1 part per million. Surface water from rivers, lakes, or the sea with marine traffic, nearby pipelines, or regular flooding can be contaminated by hydrocarbons. Freshwater treatment systems can be damaged by hydrocarbons or allow them to pass through undetected. Desalination systems using reverse osmosis (RO) membranes can be irreversibly damaged by the presence of hydrocarbons. Continuous monitoring of water source intakes can prevent system contamination and subsequent damage.  Accurate, low maintenance monitoring systems such as the TD-4100 XD and XDC have been protecting water intakes worldwide for over 20 years.

    By Turner Designs Hydrocarbon Instruments, Inc. based in Fresno, CALIFORNIA (USA).

  • Water Monitoring and Flow Measurement Systems for Water Supply

    Although there is enough water on earth, its uneven distribution, the rising population and our carelessness drinking water starts to get short. In the future more and more pipelines for drinking water will be built all over the globe. In order to operate huge and complex pipe networks efficiently, water flow measurement and flow monitoring will become necessary. The increasing efficiency of ultrasonic flow meters will make such calculations more and more effective.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Turbidity Monitoring

    The monitoring of Turbidity is key requirement of the water industry in both water supply and water recovery systems. Within the water supply process, monitoring of turbidity allows operators to assess the efficiency of filters for particulate removal through the process. Similarly, with water recovery (Waste Water Treatment Works), the measurement of turbidity is a key parameter to track the removal of particulate through the process. CTG can provide turbidity measurements with the UniLux sensor, or provides turbidity as one of the parameters available within the 3 channel TriLux. For applications requiring turbidity measurements compliant to ISO07027:1999, CTG can offer the TurbiLux Nephelometer.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Premium

    Gas analysis & monitoring system for water - natural sciences

    In nature, the chemical elements can be represented by more isotopes, or atoms of the same element, characterized by a different number of neutrons in the nucleus. When the proton / neutron ratio does not exceed that value likely to upset the balance of the atom, resulting in the phenomenon known as stabilization of radioactive decay, the isotope is called stable. That is, over time, will not tend to emit energy and sub-nuclear particles to gain energy stability, giving rise, at the end of the process, the daughter nucleus (a different element, characterized by stability energy).

    By ETG Risorse e Tecnologia based in Montiglio, ITALY.

  • Water Monitoring and Flow Measurement Systems for Hydrology

    In recent years acoustic flow measurement and flow metering has established itself as the standard method for measurement in many hydrological stations but is also used as the basis for various applications, for example for flood protection and flood forecasting. Ultrasonic flow meters are also used in hydro-engineering constructions. With this almost contact free technology data can be recorded continuously and it provides 24/7 monitoring. Such flow monitoring is particularly important in waterways used for shipping, transportation, irrigation, drainage and for cooling water extraction of power plants. A further important use of transit-time open channel flow meters is the transportation of water used for the supply of drinking water. Here the focus lies on detecting the flow rate of water loss at an early stage as it is sometimes difficult to detect small leakages.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Monitoring engineering systems for wastewater treatment industry

    Sometimes an `off the shelf` water quality monitoring product is just not available and it is necessary to engineer a complete bespoke monitoring solution. System integration demands a diverse range of abilities. PPM is experienced in designing the correct suite of instrumentation combining manufactured, distributed and factored products.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Water quality monitoring systems for feedwater, storm & condensate industry

    The most important parameters in Water/Steam Cycles such as Cation conductivity, dissolved oxygen and pH are available as pre-assembled and factory tested units. Dedicated analyzers for sodium, silica, phosphate and hydrazine are also factory tested and calibrated for immediate operation.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Water Monitoring and Flow Measurement Systems for Water Power

    Hydro power contributes to supplying approximately 3,5 per cent of electric energy generated worldwide. Its share in power generation from renewable resources lies at 18 per cent and will continue to grow as resources of fossil fuels are depleted. Hydro electric performance depends essentially on the usable altitude difference between upper and lower reservoir, and hence the resulting water flow. In order to use the “fuel” water in an optimal way, the flow velocity has to be monitored without any interruptions. Ultrasonic flow meters, flow sensors and clamp-on flow meters (OR clamp-on technology) are ideal for accurate flow metering and flow monitoring.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Water quality monitoring systems for wastewater & effluents monitoring industry

    Instruments for monitoring the aeration-process, nitrification and de-nitrification; chlorination and de-chlorination; as well as the final discharge into the environment.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Chromatography systems for environmental monitoring

    With the growth of contamination generated from agricultural and industrial production, it causes a threat to the enviroment including drinking water, atmosphere and soil. The chemists have always seeked out the effective analytical methods to detect and identify chemical contaminants. Dikma provides innovative products and application solutions according to government regulations and industry standards, for air and water quality monitoring, gas detection.

    By Dikma Technologies Inc. based in Lake Forest, CALIFORNIA (USA).

  • Real-time In-situ Effluent Monitoring

    The UviLux BOD Indicator enables in-situ, real-time, reporting of BOD within both natural water systems and water processing plants. The monitor detects fluorescent proteins that are inherent within sewage and slurry and provides an output in BOD equivalent units. The principle behind the measurement is the excitation of Tryptophan-like fluorescence within UV wavelength band, which has been shown to correlate with both BOD and bacterial contamination. With complete flexibility of deployment methodology, the UviLux BOD Indicator can be applied to both water supply and water recovery processing plants. For water supply processing, the UviLux BOD Indicator can be applied at the front end to the water intake to provide alarm of any contaminated water entering the plant. Applications within Waste Water Treatment Works can include monitoring of effluent levels at the final outflow point (into rivers and coastal areas) as well as the primary, secondary & tertiary stages, the data potentially feeding into energy saving systems to optimise process performances. The CTG UviLux BOD Indicator in-situ fluorometer can also be used within pipe and channel networks to test for incidences of black water and grey water cross-over.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Continuous Monitoring of Wastewater

    The Sorbisense method allows for efficient monitoring of the sewage system and can help reduce costs of operation and environmental impact. The method is particularly well suited for tracking the source of periodic discharges, the identification of faulty pipe connections of the measuring of values in the recipient. The method also allows for measurements in dynamic sources - such as emissions from roads, roofs, parking lots and overflow

    By Sorbisense A/S based in Tjele, DENMARK.

  • Premium

    Water monitoring technology for flood warning

    Flood warning systems built into hydrological stations are used to notify local emergency authorities in the case of a flood event.

    By OTT Hydromet - a member of Hach Company based in Kempten, GERMANY.

  • Water quality monitoring systems for high water purifier industry

    The monitoring of “Ultra Pure Water” or “High Purity Water” requires the lowest possible detection limits for process analyzers. Resistivity is often around 18 MΩ. Dedicated instruments can detect infinitely small amounts (ppt e.g. parts per trillion) of ions.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Water quality monitoring systems for cooling water treatment industry

    A number of treatment products are often added to prevent corrosion, scaling and fouling. Coating of sensors and other effects of these products must be taken into account when selecting analyzers. Discharge monitoring needs special attention because zero measurements must be reliable over time with little maintenance.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you