Only show results available in Virginia? Ok

water quality sampling Applications

  • Water Data Management Solution for Water Quality

    Monitor any water quality parameter you collect, no matter where it has been collected from. Store quality data from manually or automatically collected spot samples, and even continuously collected samples such as those from auto-samplers and sondes.

    By KISTERS AG based in Aachen, GERMANY.

  • Laser detection solutions for water-quality monitoring

    The technology of Spectral Fluorescence Signatures (SFS) is a very sensitive and selective tool to monitor many industrial processes on site and in real-time. The SFS analyzer series – SFS-Scanner and Instant Screener spectrofluorometers - are capable of detecting target substances even in complex mixtures without any pre-treatment of the samples.

    By Laser Diagnostic Instruments AS based in Tallinn, ESTONIA.

  • Water measurement systems & sensors for water quality monitoring

    Effective water quality monitoring is the key to environmental protection of watercourses and for reliable process control and wastewater treatment.  Discharge consents under EPR regulations dictate that water quality monitoring is undertaken to ensure that consented parameters are below the consented concentrations.  Traditionally this has been done using water quality sampling methods but increasingly automatic water quality measurement sensors linked to real-time telemetry is seen as the most reliable and timely means of ensuring that treatment processes are operating efficiently and that EPR compliance is maintained.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Sample preparation and pumping systems for wastewater treatment industry

    A wide range of sample acquisition and filtration systems are available to prepare even the most difficult of samples for reliable on-line analyser measurement. The correct choice is often critical to prevent analyser blockage and optimise performance. Cross Flow Filtration The PPM cross flow filter, is a simple in-line device used to protect an analyser from ingress of solids, for applications where sample quality is generally good but occasionally suspended solids may be present. The stainless steel filter removes solids above 50 micron size.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Water Data Management Solution for Urban Hydrology

    Use KISTERS solutions to manage all of the various data from your Urban Water Management programs. From water distribution to water treatment, infiltration and inflow studies, groundwater, as well as long term precipitation monitoring and real time control systems. An optional water quality module is also available to manage your discrete sample data.

    By KISTERS AG based in Aachen, GERMANY.

  • Microbial testing for water treatment industry

    Why wait until tomorrow to know today`s water quality? How clean is your water? Don`t take chances on microbiological contamination! Through fast, portable, and accurate testing, LuminUltra`s Quench-Gone Aqueous (QGA™) test kit instantly measures the total microbiological content of any water sample to detect emerging growth and locate the source of contamination. This takes the guess-work out of managing water distribution systems and aids with disinfection and flush cycles. LuminUltra`s QGA test is the ideal tool to help save time & money and reduce risk in water treatment and distribution!

    By LuminUltra Technologies Ltd. based in Fredericton, NEW BRUNSWICK (CANADA).

  • Premium

    High quality gas sensor solutions for total organic carbon (TOC)

    Minimising costs through measurement of CO2 concentration. Both water suppliers and water users need to know the quality of the water they are supplying, using and disposing of so as to minimise their costs. One measure of water quality is the organic carbon content (TOC). TOC is measured by oxidising the organic carbon to produce CO2 which is then measured and the value converted into a TOC measurement. Edinburgh Sensors supply sensors to measure the CO2 concentration produced by oxidising the organic carbon in a water sample, allowing the TOC to be calculated. This TOC value determines one measure of how clean the water sample is.

    By Edinburgh Instruments Ltd based in Livingston, UNITED KINGDOM.

  • Phosphonate Testing in Hard Water

    Testing phosphonates in hard water can be difficult due to interference from high levels of calcium. Here we present a phosphonate test method for hard water samples. The method is based on a chemical masking of the calcium. The WAT hard water phosphonate test uses C30 Spectrophotometer to measure the chromogen PMB and digital thermoreactor to digest the phosphonate compound. The thermoreactor capacity of 16 simultaneous vials provides for running critical data quality assurance samples.

    By WAT Australia Pty.Ltd. based in West Australia, AUSTRALIA.

  • Agricultural, Storm and Highway Runoff

    The ability to collect useful data about sediment transport and other pollutants closely coupled to SSC (such as nutrients, e-coli, phosphates and nitrates) is dependent on the timing and frequency of manual grab samples during run-off events. Most sediment and pollutant is transported during a small number of storm events which are infrequent and unpredictable. When they do occur, trained personnel or the proper equipment may not be available to collect grab samples. An automated pump sampler can eliminate the need to sample manually, but for the expense of a rechargeable power system, the autosampler, and possibly a datalogger and a typical turbidity probe, you’re no better off. With an automated pump sampler driven by the DTS-12 digital turbidity sensor and controlled by the Axiom H2 datalogger, you obtain a better understanding of the water’s quality, while taking a minimum number of samples, reducing site visits and saving lab analysis costs.

    By FTS based in Victoria, BRITISH COLUMBIA (CANADA).

  • EPR waste minimisation monitoring for wastewater treatment industry

    The EPR regulations have replaced the IPPC regulations and are effective from May 2009 for qualifying companies within the industrial sector and October 2009 within the water sector. They will progressively require industry to minimise waste, reduce product loss and implement improved process control. The legislation will require the operator to self monitor processes and discharges, to demonstrate effective control with particular emphasis on EPR compliance and prevention. The regulating Agency will operate a point scoring system to assess operators under the OMA-3 program and this will be used to identify how well a company is managing their processes and possibly identify areas for improvement. The Environmental Permitting Regulations require industry to install instrumentation (MCERTS approved where available) to report water quality. EPR compliance monitoring may include automatic water sampling, flow measurement, pH, turbidity and TOC water analysis. Industry will need to identify point of source emissions, take steps to correct inefficient control and alarm unacceptable process deviations. Although the legislation focuses on environmental improvement, good housing keeping also makes a lot of sense. Optimisation of process control minimises waste, reduces treatment costs and ultimately saves money.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Microbial testing in food & beverage industry

    Why wait until tomorrow to know today`s water quality? How clean is your water? Don`t take chances on microbiological contamination! Through fast, portable, and accurate testing, LuminUltra`s Quench-Gone Aqueous (QGA™) test kit instantly measures the total microbiological content of any water sample to detect emerging growth and locate the source of contamination. This takes the guess-work out of managing water treatment and distribution systems used in the food and beverage industry, and aids with disinfection practices and flush cycles. LuminUltra`s QGA test is the ideal tool to help save time & money and reduce risk in food & beverage water management!

    By LuminUltra Technologies Ltd. based in Fredericton, NEW BRUNSWICK (CANADA).

  • APHA Color #3020

    Measurement of APHA color either on-line or in a laboratory setting using a photometer. Background: APHA is sometimes referred to as the Platinum Cobalt (Pt/Co) or Hazen scale. Also referred to as a “yellowness index”, the APHA color scale is a common method of comparison of the intensity of yellow-tinted samples to assess the quality of liquids that are clear to yellowish in color. Originally developed to determine the purity of municipal water supplies, it is now used as a metric for purity in the water, chemical, oil, plastics, and pharmaceutical industries. APHA color quantifies the appearance of trace amounts of yellowness, which is a visual indicator of product degradation due to exposure to light or heat; the presence of impurities and negative effects of processing. As such APHA color is often used as a product release specification. APHA is a single number yellowness index. The units are based on a dilution of a 500ppm solution of PtCo.

    By Guided Wave Inc, based in Rancho Cordova, CALIFORNIA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you