Only show results available in Virginia? Ok

water sampling system Applications

  • Sample preparation and pumping systems for wastewater treatment industry

    A wide range of sample acquisition and filtration systems are available to prepare even the most difficult of samples for reliable on-line analyser measurement. The correct choice is often critical to prevent analyser blockage and optimise performance. Cross Flow Filtration The PPM cross flow filter, is a simple in-line device used to protect an analyser from ingress of solids, for applications where sample quality is generally good but occasionally suspended solids may be present. The stainless steel filter removes solids above 50 micron size.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Water measurement systems & sensors for water quality monitoring

    Effective water quality monitoring is the key to environmental protection of watercourses and for reliable process control and wastewater treatment.  Discharge consents under EPR regulations dictate that water quality monitoring is undertaken to ensure that consented parameters are below the consented concentrations.  Traditionally this has been done using water quality sampling methods but increasingly automatic water quality measurement sensors linked to real-time telemetry is seen as the most reliable and timely means of ensuring that treatment processes are operating efficiently and that EPR compliance is maintained.

    By Isodaq Technology - Hydro-Logic Group based in Bromyard, UNITED KINGDOM.

  • Water Data Management Solution for Urban Hydrology

    Use KISTERS solutions to manage all of the various data from your Urban Water Management programs. From water distribution to water treatment, infiltration and inflow studies, groundwater, as well as long term precipitation monitoring and real time control systems. An optional water quality module is also available to manage your discrete sample data.

    By KISTERS AG based in Aachen, GERMANY.

  • Microbial testing for water treatment industry

    Why wait until tomorrow to know today`s water quality? How clean is your water? Don`t take chances on microbiological contamination! Through fast, portable, and accurate testing, LuminUltra`s Quench-Gone Aqueous (QGA™) test kit instantly measures the total microbiological content of any water sample to detect emerging growth and locate the source of contamination. This takes the guess-work out of managing water distribution systems and aids with disinfection and flush cycles. LuminUltra`s QGA test is the ideal tool to help save time & money and reduce risk in water treatment and distribution!

    By LuminUltra Technologies Ltd. based in Fredericton, NEW BRUNSWICK (CANADA).

  • Microbial Solutions for Wastewater Treatment

    Whether industrial or municipal, Microbial Discovery Groups proprietary platforms address the variety of challenges associated with wastewater treatment. Too many failures in the bioaugmentation industry stem from focusing on the product, rather than understanding and complementing wastewater systems and operations. MDG will work with you to provide customized system surveys, sampling and testing results, return on investment proposals, and regular monitoring programs specific to your end user customer. We will show you how to measure success and provide sustainable turnkey solutions for your client.

    By Microbial Discovery Group (MDG) based in Franklin, WISCONSIN (USA).

  • Sediment and Nutrient Loads

    SedEvent is an event-driven, automatic grab sampling system that provides a simple and practical method of accurately determining suspended sediment and nutrient loads. While suspended sediment concentration (SSC) cannot be directly measured accurately or reliably, turbidity has been shown to be an excellent surrogate for SSC. Turbidity is caused by suspended particulate matter such as clay, silt, algae, organic and inorganic chemicals and acids like fertilizers, and microscopic organisms like harmful bacteria. These contents give water its cloudy or turbid appearance, and turbidity in natural waters is recognized as an important indicator of natural health. Measuring suspended sediment concentrations used to be labor-intensive, costly, inaccurate and impractical. SedEvent not only makes it possible and practical, it makes it simple.

    By FTS based in Victoria, BRITISH COLUMBIA (CANADA).

  • US Peroxide Rapid Response

    US Peroxide (USP) is uniquely positioned to rapidly respond to your environmental treatment challenges. USP combines experienced applications and equipment field support with a large inventory of storage systems and pumping modules to respond quickly to time sensitive water and wastewater treatment situations. Advantages With considerable inventory of tank and pump systems as well as our partnerships with leading chemical suppliers, USP can mobilize chemicals and equipment quickly to respond to your rapid response needs, often within 24 hours. We offer dosing options are designed to meet all safety requirements and sized to meet your specific process and dosage rates requirements. Our Applications Engineers and Equipment and Engineering Services teams will provide timely and thorough applications assistance and technical support during the entire project. Download the Rapid Response Solutions Brochure (PDF) Sample Applications Examples of where our Rapid Response Program has successfully addressed treatment challenges include the following: Temporary application of hydrogen peroxide as a source of supplemental dissolved oxygen in biological treatment systems during periods of excessive BOD loading Hydrogen peroxide pretreatment of high strength wastewater to reduce toxicity or BOD/COD prior to biological treatment Emergency hydrogen peroxide treatment of lagoons or ponds to control hydrogen sulfide and other odors Shock cleaning of cooling water systems for biofouling and slime control

    By USP Technologies based in Atlanta, GEORGIA (US) (USA).

  • Agricultural, Storm and Highway Runoff

    The ability to collect useful data about sediment transport and other pollutants closely coupled to SSC (such as nutrients, e-coli, phosphates and nitrates) is dependent on the timing and frequency of manual grab samples during run-off events. Most sediment and pollutant is transported during a small number of storm events which are infrequent and unpredictable. When they do occur, trained personnel or the proper equipment may not be available to collect grab samples. An automated pump sampler can eliminate the need to sample manually, but for the expense of a rechargeable power system, the autosampler, and possibly a datalogger and a typical turbidity probe, you’re no better off. With an automated pump sampler driven by the DTS-12 digital turbidity sensor and controlled by the Axiom H2 datalogger, you obtain a better understanding of the water’s quality, while taking a minimum number of samples, reducing site visits and saving lab analysis costs.

    By FTS based in Victoria, BRITISH COLUMBIA (CANADA).

  • EPR waste minimisation monitoring for wastewater treatment industry

    The EPR regulations have replaced the IPPC regulations and are effective from May 2009 for qualifying companies within the industrial sector and October 2009 within the water sector. They will progressively require industry to minimise waste, reduce product loss and implement improved process control. The legislation will require the operator to self monitor processes and discharges, to demonstrate effective control with particular emphasis on EPR compliance and prevention. The regulating Agency will operate a point scoring system to assess operators under the OMA-3 program and this will be used to identify how well a company is managing their processes and possibly identify areas for improvement. The Environmental Permitting Regulations require industry to install instrumentation (MCERTS approved where available) to report water quality. EPR compliance monitoring may include automatic water sampling, flow measurement, pH, turbidity and TOC water analysis. Industry will need to identify point of source emissions, take steps to correct inefficient control and alarm unacceptable process deviations. Although the legislation focuses on environmental improvement, good housing keeping also makes a lot of sense. Optimisation of process control minimises waste, reduces treatment costs and ultimately saves money.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Analysis of aqueous solutions

    IR-Spectroscopy is not limited to gases, solid materials and pure liquids but also facilitates the measurement of solutes in aqueous media. Though, due to the strong and temperature dependent absorption of water, the usage of conventional IR-transmission and ATR accessories is not very suitable for the analysis in water. The CONFOCHECK is a dedicated FT-IR system for the fast, easy and sensitive analysis of aqueous samples. Using this system, preparing, measuring and evaluating any aqueous sample takes typically about 1 minute.

    By Bruker Corporation based in Billerica, MASSACHUSETTS (USA).

  • Gas Analysis Systems for Catalysis, Thermal Analysis, Fermentation and Bio Fuels

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas and vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, and include a range of special sampling, vacuum pumping and vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, and thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR, studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour and CH4 in the PPM to 100% concentration range provides vital information for process development and process monitoring.

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Premium

    Determination of Additives in Beverages using Ascentis Express Columns

    Beverages, such as sodas and energy drinks, can include a number of polar ingredients, which are easily soluble in the water matrix of the drinks. These ingredients include sweeteners (sugars and sugar substitutes), caffeine, vitamin supplements, amino acids, organic acids, and plant extracts. Because the analytes are already in solution, there is no need for extensive sample preparation. Dilution followed by direct injection into an HPLC is typically suitable. In this article we present two beverage applications using Ascentis Express HPLC columns. Ascentis Express columns offer faster HPLC on any system. One benefit is their ability to produce the resolution, efficiency, and speed on conventional HPLC systems that is associated with the use of sub-2 micron columns on a UHPLC system, without generating high backpressure. Column chemistries (RP-Amide and HILIC) were selected for this article based on their enhanced performance with polar compounds in comparison to C18.

    By Sigma-Aldrich Co., LLC based in Bellefonte, PENNSYLVANIA (USA).

  • Independent particle characterization services for environmental industries

    Particle size, particle concentration and other physical characterization analyses are critical to many environmental applications. Regulatory agencies in the environmental sphere demand strict compliance to standards and discharge regulations. Physical testing of samples for parameters such as particle size and concentration can give insight to the process control engineer on how effective and compliant a discharge handling system is operating. Particulate loading from both air emissions and waste water discharge are monitored in many industry sectors and PTL testing provides valuable supporting data in this monitoring process.

    By Particle Technology Labs based in Downers Grove, ILLINOIS (USA).

  • Exhaust Gas Emissions

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas/vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping & vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, & thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour & CH4 in the PPM to 100% concentration range provides vital ininformation for process development and process monitoring...

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Microbial Studies

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas/vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping & vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, & thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR studies, Hiden gas analysis systems include enhanced pumping for hydrogen & special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour & CH4 in the PPM to 100% concentration range provides vital information for process development and process monitoring.

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Beverage Analysis

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas/vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping and vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, & thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour & CH4 in the PPM to 100% concentration range provides vital information for process development and process monitoring

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Fragrance Fingerprinting

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas & vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping & vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, and thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR, studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour and CH4 in the PPM to 100% concentration range provides vital information for process development and process monitoring.

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Microbial testing in food & beverage industry

    Why wait until tomorrow to know today`s water quality? How clean is your water? Don`t take chances on microbiological contamination! Through fast, portable, and accurate testing, LuminUltra`s Quench-Gone Aqueous (QGA™) test kit instantly measures the total microbiological content of any water sample to detect emerging growth and locate the source of contamination. This takes the guess-work out of managing water treatment and distribution systems used in the food and beverage industry, and aids with disinfection practices and flush cycles. LuminUltra`s QGA test is the ideal tool to help save time & money and reduce risk in food & beverage water management!

    By LuminUltra Technologies Ltd. based in Fredericton, NEW BRUNSWICK (CANADA).

  • Monitoring of VOCs in Porewater

    Monitoring VOCs in porewater in the unsaturated zone is now possible.

    Sorbisense regularly offers new options for using the patented Sorbicell, which is used to monitor surface water, wastewater and groundwater.

    The latest is almost as “ground-breaking” as the SorbiCell itself. Until now it has been difficult, if not impossible, to directly monitor for volatile substances in pore water in the unsaturated zone. But the environmental consultancy firm Ejlskov A/S in Aarhus combined the use of Sorbisense sampling equipment with the proven technology of soil water samplers. With this combination, a practical new method is made available, which allows for monitoring the presence of porewater-dissolved VOCs above the groundwater table. This provides a significantly improved basis to define and determine the leaching risk to the groundwater, and thus allows for better and more cost-efficient decisions to prevent the pollution in reaching the groundwater.

    A simple construction with multiple options

    The application uses SorbiCell VOC combined with suction cells, soil water samplers. When installed correctly, and applied with the correct procedures, the suctions cells extract capillary bound water from the soil matrix. The system demands no other resource than a container that is put under vacuum. The vacuum in the container then ensures a flow through of the Sorbicell over a period of time, fx. 2-3 weeks. The method is highly suitable for monitoring a site over longer periods of time.

    By SORBISENSE based in Tjele, DENMARK.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you