Only show results available in Virginia? Ok

well water sampling Applications

  • Water Data Management Solution for Urban Hydrology

    Use KISTERS solutions to manage all of the various data from your Urban Water Management programs. From water distribution to water treatment, infiltration and inflow studies, groundwater, as well as long term precipitation monitoring and real time control systems. An optional water quality module is also available to manage your discrete sample data.

    By KISTERS group based in Aachen, GERMANY.

  • Premium

    Oil in Water Analysis for Flowback or Produced Water

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water. Waiting for remote lab results can take several days to a week. InfraCal TOG/TPH Analyzers allow for oil in water testing at the well site in less than 10 minutes. The sampling requires a few simple steps that can be performed by non-technical personnel. The water is mixed with the extraction solvent, shaken, and then presented to the analyze for measurement. The same InfraCal TOG/TPH Analyzer can be used for TPH in soil if a spill or pond leak occurs to determine the contaminated area. The analyzer features: -Results in under 15 minutes -Detect levels as low as 10 ppm -Portable, rugged, lightweight, easy-to-use -Battery operable -Ideal for field or lab use

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • Waste water respirometry solutions for toxicity tracking

    If toxicity is identified in a mixed sewage entering a treatment works, the problem for the plant manager is to track and identify the source of the toxicity. This can be done by sampling the effluent stream at various points in its length. By working in a logical sequence back up the sewer network the number of samples can be minimised. This type of testing should be rigorously enforced for new product introduction by a waste producer, as well as sampling the effluents directly at source. The samples would be tested against the activated sludge of the receiving works, using the Respiration Inhibition Test or the Nitrification Inhibition Test.

    By Strathkelvin Instruments Ltd. based in Motherwell, UNITED KINGDOM.

  • US Peroxide Rapid Response

    US Peroxide (USP) is uniquely positioned to rapidly respond to your environmental treatment challenges. USP combines experienced applications and equipment field support with a large inventory of storage systems and pumping modules to respond quickly to time sensitive water and wastewater treatment situations. Advantages With considerable inventory of tank and pump systems as well as our partnerships with leading chemical suppliers, USP can mobilize chemicals and equipment quickly to respond to your rapid response needs, often within 24 hours. We offer dosing options are designed to meet all safety requirements and sized to meet your specific process and dosage rates requirements. Our Applications Engineers and Equipment and Engineering Services teams will provide timely and thorough applications assistance and technical support during the entire project. Download the Rapid Response Solutions Brochure (PDF) Sample Applications Examples of where our Rapid Response Program has successfully addressed treatment challenges include the following: Temporary application of hydrogen peroxide as a source of supplemental dissolved oxygen in biological treatment systems during periods of excessive BOD loading Hydrogen peroxide pretreatment of high strength wastewater to reduce toxicity or BOD/COD prior to biological treatment Emergency hydrogen peroxide treatment of lagoons or ponds to control hydrogen sulfide and other odors Shock cleaning of cooling water systems for biofouling and slime control

    By USP Technologies based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Mercury monitoring for ocean cruises

    Researchers at Battelle Pacific Northwest Laboratory used a Tekran 2600 on a 2009 ship cruise. Due to the low levels of mercury in water, Tekran provided them with a custom 2600 Event Table to pre-concentrate mercury from multiple samples to push the detection limit lower. When planning an ocean bound cruise, instrument dependability is a paramount concern. At sea, there is no possibility to return instrumentation to the manufacturer for quick repair. The Tekran 2600 has a well deserved reputation for dependability and performance. If any repairs are necessary, the instrument is highly user-serviceable and easy to maintain.

    By Tekran Instruments Corporation based in Knoxville, TENNESSEE (USA).

  • EPR waste minimisation monitoring for wastewater treatment industry

    The EPR regulations have replaced the IPPC regulations and are effective from May 2009 for qualifying companies within the industrial sector and October 2009 within the water sector. They will progressively require industry to minimise waste, reduce product loss and implement improved process control. The legislation will require the operator to self monitor processes and discharges, to demonstrate effective control with particular emphasis on EPR compliance and prevention. The regulating Agency will operate a point scoring system to assess operators under the OMA-3 program and this will be used to identify how well a company is managing their processes and possibly identify areas for improvement. The Environmental Permitting Regulations require industry to install instrumentation (MCERTS approved where available) to report water quality. EPR compliance monitoring may include automatic water sampling, flow measurement, pH, turbidity and TOC water analysis. Industry will need to identify point of source emissions, take steps to correct inefficient control and alarm unacceptable process deviations. Although the legislation focuses on environmental improvement, good housing keeping also makes a lot of sense. Optimisation of process control minimises waste, reduces treatment costs and ultimately saves money.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Concerned about PAHs in Parking Lot Sealcoats?

    There is growing concern - and regulations in the works - over the use of sealcoating products due to their high PAH content.  In the United States and elsewhere, most sealcoats are made from coal tar which can be toxic to aquatic life and threaten public water supplies from rain and runoff. Sitelab can be used to quickly check the concentrations of polycyclic aromatic hydrocarbons and determine if it's made from coal tar or alternative petroleum based black top sealants.  Got samples?  We'll test them for free!  Contact Sitelab Corporation for details.

    By Sitelab Corporation based in West Newbury, MASSACHUSETTS (USA).

  • X-ray fluorescence XRF analysis for environmental protection and waste management

    To meet the requirements of new regulations and to protect the environment effectively, industries need techniques that enable the analysis of elements at lowest concentration levels. Bruker X-ray fluorescence (XRF) analysis is the most suitable analytical technique for handling different kinds of materials. Bruker’s XRF, ICP-MS, GC, TOF-MS, FT-IR, CBRNE products and applications help you to monitor contaminated land efficiently and quickly, to determine hazardous elements in the air and water, as well as to classify waste material and to specify products for recycling and disposal. Whether solids, sludge, filters, liquids or powders: there is a fast and simple sample preparation technique for every material type.

    By Bruker Corporation based in Billerica, MASSACHUSETTS (USA).

  • Environmental Monitoring

    Environmental monitoring is becoming more important every day in local, national and international policies, showing the environmental awareness demanded by society.

    This fact gives rise to an increase in the amount of legislation that obliges companies to law enforcement. Thus, the necessity of making more pollutants controls means high analysis expenses to the companies, which need to subcontract this service.

    Although applications in this area advance, there is still a clear demand to get new portable and versatile analysis systems for many different application fields such as pollution in environmental or waste waters, monitoring nutrients in agricultural or horticultural water as well as general process control in chemistry industry. Because of the number of enviromental analysis required, there is a need for screening and monitoring measurements of these compounds at contaminated areas.

    Traditional monitoring techniques are typically based on laboratory analysis of field-collected samples that require considerable effort and expense, and the sample may change before analysis. Moreover, the equipment currently available is too large and expensive and it cannot be made portable.Alternatively, microfluidic and electrochemical sensor technologies can contribute to the development of new portable monitoring systems, complementing standard analytical methods for different environmental monitoring applications.In this way, the decentralization and integration of all those typical analyses is the paramount importance in order to reduce cost, simplify the analytical process and make more accessible these technologies to end-users. The development of portable, robust, and accurate Lab-on-a-Chip systems to monitor priority compounds such as contaminants, explosives, chemical warfare agents, inorganic and organic ions is a demand of modern society. Portability allows analyses to be carried out outside of the laboratory, minimizing the risk of contaminating the sample and leading to a faster response time at a lower cost.

    Thus, MicruX solutions and technologies open the gate to develop portable and esay-handly Lab-on-a-Chip devices in order to improve pollutants in-situ analysis in a very economic and efficient way.

    By MicruX Technologies based in Oviedo, SPAIN.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you