Only show results available in Virginia? Ok

wood heating Applications

  • Premium

    Industrial briquette presses for Wood briquetting

    No matter where wood chips come from, whether it is hard or soft wood, chipboard, MDF, plywood, wood shavings, saw dust or swarf: volume can be reduced by up to 90 %. This is particularly attractive to the furniture industry, saw mills and cabinetmaking. With briquette presses from WEIMA, now valuable wood waste can be processed to compact briquettes and sold or used as an own heating source. In general, briquettes have a high calorific value, much higher than regular firewood and comparable to brown coal brought about by a longer and more even burning process. By the way, less ash is also produced.

    By WEIMA based in Ilsfeld, GERMANY.

  • Wood Cogeneration for Farms

    Farming operations that require heat also benefit from the CHP system. The return on investment will vary dependent on whether there is low or no cost access to wood chips and whether the 45 kWh of power can be fully utilized on site or, if not, what rate the power can be sold to the grid.

    By Borealis Wood Power Corp. based in Burlington, ONTARIO (CANADA).

  • Wood Cogeneration for Industry

    Any company that has a need for both heat and power is an ideal fit for the Borealis wood power system, especially if located in a rural setting where energy costs are high. The application requirement must be for the full 45 kWh of power for immediate use. If power requirement is not that high, then this energy can be sold to the regional power grid often at preferred rates. Options for off-grid solutions are being reviewed.

    By Borealis Wood Power Corp. based in Burlington, ONTARIO (CANADA).

  • Wood Cogeneration for Greenhouses

    Greenhouse operations have been early adopters of the CHP system given their operation’s need for heat. The return on investment is dependent on the regional rate for selling the power to the grid and also the utilities saved from CHP heat.

    By Borealis Wood Power Corp. based in Burlington, ONTARIO (CANADA).

  • Wood Cogeneration for Rural Communities

    Small rural communities or work camps are ideal applications for the Borealis wood power plant. Its application fit is best when the heat can be used to support a micro-heating-network for 25 homes or fewer in conjunction with a community centre as base load. Power needs must exceed the 45 kWh or it can be sold to the grid.

    By Borealis Wood Power Corp. based in Burlington, ONTARIO (CANADA).

  • Premium

    Air pollution control (APC) equipments for forest industry

    In the forest industry, it becomes increasingly important to improve energy efficiency. EnviBAT specializes in gas/gas heat exchange where heat is recovered from the outgoing gas streams, and mist gas condenser, where large amounts of heat can be recovered from the sulphate pulp mills.

    By Envibat AB based in Skellefteå, SWEDEN.

  • Pyrolysis oil to diesel

    Pyrolysis oil to diesel continuous waste pyrolysis oil to diesel Solution: Oil refining machine Applicable: Tire oil, Plastic oil, Waste oil, Pyrolysis oil,Engine oil, Black oil, Heavy oil, etc Output: 85-90% good clean oil, the rest is slag and waste gas Heating fuel: Coal / wood/ fuel oil / gas Oil refining machine land size: 20X15m Reactor material:Q245/ Q345 Boiler plate

  • Continuous process waste plastic to oil recycling

    continuous waste plastic to oil Solution: Continuous pyrolysis plant Function: Recycling waste plastic to fuel oil Applicable raw material: ABS / Mixed plastic, PE/PP/PS Plastic, PET Plastic not recommended Output: 50-90% fuel oil ,10-50% carbon blakc Heating fuel: Coal / wood/ fuel oil / gas Pyrolysis plant land size: 25x20m Reactor design: Mutiple reactors with internal rotating Reactor material: Q245/ Q345 Boiler plate

  • Continuous process waste tyre to oil recycling

    Solution: Continuous pyrolysis plant Function: Recycling waste tire to fuel oil Applicable raw material: Car tire, Truck tires, OTR tries, etc Output: 45-52% crude oil, 30% carbon black,12-15%steel wire, 8% waste gas Heating fuel: Coal / wood / fuel oil / gas Pyrolysis plant land size: 25x20m Reactor design: Mutiple reactors with internal rotating Reactor material: Q245/Q345 Boiler plate

  • Premium

    Gas Sensing for Gasification

    Syngas (short for synthetic gas) can be burnt and used as a fuel source, the main constituents of syngas are Carbon Monoxide (CO) and Hydrogen (H), which amount for around 85% of Syngas, and it is produced by a process called Gasification. Gasification starts with a base material which can originate from a wide variety of materials for example wood chips and pellets, plastics, municipal solid waste, sewage, waste crops, and fossil fuels such as coal. During Gasification the base material is reacted at high temperature without combustion with controlled amounts of oxygen (O) or steam. The composition of the base material combined with the amount of oxygen and heat used in the process affects the composition of the resultant SynGas, in which the CO can vary between around 20 and 60%. In addition, large amounts of H and CO are also formed. The measurement of CO is therefore an important feature in the production of SynGas.

    By Edinburgh Instruments Ltd based in Livingston, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you