Applications in Alaska

  • Premium

    Reverse Osmosis Water Testing

    Osmosis is the phenomenon of lower dissolved solids in water passing through a semi-permeable membrane into higher dissolved solids water until a near equilibrium is reached. Reverse Osmosis (RO) is a membrane process of purification which removes most of the the total dissolved solids (TDS) in water by reversing the natural process of osmosis. Pressure is applied to a TDS-concentrated solution against a semi-permeable membrane, causing pure water to diffuse through the membrane. RO has become an important process for a wide variety of applications including: medical, laboratory, desalination, industrial wastewater, Deionized (Dl) pretreatment, and drinking water.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Pool Water Testing / Spa Water Testing

    Anyone and everyone who is responsible for operating and maintaining a swimming pool or spa has to test, monitor, and control complex, interdependent chemical factors that affect the quality of water bathers are immersed in. Additionally, aquatic facilities operators must be familiar with all laws, regulations, and guidelines governing what these parameters should be.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Oxidation Reduction Potential (ORP)/Redox

    Oxidation Reduction Potential or Redox is the activity or strength of oxidizers and reducers in relation to their concentration. Oxidizers accept electrons, reducers lose electrons. Examples of oxidizers are: chlorine, hydrogen peroxide, bromine, ozone, and chlorine dioxide. Examples of reducers are sodium sulfite, sodium bisulfate and hydrogen sulfide. Like acidity and alkalinity, the increase of one is at the expense of the other.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Deionized Water Testing

    Years ago, high purity water was used only in limited applications. Today, deionized (Dl) water has become an essential ingredient in hundreds of applications including: medical, laboratory, pharmaceutical, cosmetics, electronics manufacturing, food processing, plating, countless industrial processes, and even the final rinse at the local car wash.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Circuit Board Cleanliness Testing

    Contamination of circuit boards can bring about severe degradation of insulation resistance and dielectric strength. Cleanliness of completed circuit boards is, therefore, of vital interest. For those companies who have established circuit board cleaning procedures, the MIL Spec P-28809 has been used as a guideline for control. Now a simple `on line` test for the relative measurement of ionic contamination has been developed. This fast and economical method for testing circuit board cleanliness uses a Myron L Company Ultrameter II™ 4P or 6P, a suitable container, and a mixture of Dl (deionized) water and alcohol.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Boiler Water Testing / Cooling Tower Water Testing

    Boilers and cooling towers share two major water related problems: deposits and corrosion. As steam is generated by a boiler or water evaporating from a cooling tower, dissolved minerals are left behind, increasing the concentration of these minerals. Additional minerals are introduced via the water added to makeup the water lost to steam/evaporation. Eventually, the minerals reach a level (or cycle) of concentration that will cause either loss of efficiency due to scale or damage from corrosion. This level can be determined by the Ryznar or Langlier indices and correlated to a conductivity or TDS range. Most people recognize problems associated with corrosion. Effects from scale deposits, however, are equally important. For example, as little as 1/8` of scale can reduce the efficiency of a boiler by 18% or a cooling tower heat exchanger by 40%!

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Water Testing for Textile Manufacturing

    The textile manufacturing industry encompasses many and diverse processes that rely heavily on the use of water, energy, chemicals, and other resources. Wet spinning, sizing, desizing, scouring, bleaching, mercerization, dyeing and printing are just a few. Monitoring and controlling the pH, TDS/Conductivity/Salt Concentration, ORP (REDOX), and Temperature of the aqueous solutions used in these processes conserves costly resources, controls quality, and reduces the amount of pollution that must be treated before discharge of effluent wastes. This can be done manually with handheld instruments or automatically with in-line monitor/controllers.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Water Testing for Environmental Applications

    Keeping the water in our lakes, rivers, and streams clean requires monitoring of water quality at many points as it gradually makes its way from its source to our oceans. Over the years ever increasing environmental concerns and regulations have heightened the need for increased diligence and tighter restrictions on wastewater quality. Control of water pollution was once concerned mainly with treating wastewater before it was discharged from a manufacturing facility into the nation`s waterways. Today, in many cases, there are restrictions on wastewater that is discharged to city sewer systems or to other publicly owned treatment facilities. Many jurisdictions even restrict or regulate the runoff of stormwater — affecting not only industrial and commercial land, but also residential properties as well.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Water Testing for Horticulture

    Modern growing practices include scientific evaluations of soil, water, fertilizers, diseases, etc. While some tests are best performed by a laboratory, others can be easily conducted on location, saving time and money. Three tests in particular, EC, pH, and ALKALINITY, can reveal valuable information about water quality, soil salinity, and fertilizer concentration. MyronL Company’s portable AGRI-METERS provide you with a simple, fast, and accurate means of testing these parameters.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Fountain Solutions

    Accurate fountain (dampening) solution concentration control is essential for consistent, high-quality results in lithography. Low concentration can cause drying on the non-image area of the plate resulting in tinting, scumming, blanket piling, etc. High concentrations, on the other hand, bring about over-emulsification of the ink. This results in weakening of color strength and changes in ink rheology (body and flow properties). Correct concentration will allow the non-image areas of the plate to be appropriately wetted.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Water Testing for Automatic Rinse Tank Controls

    Proper rinsing is one of the most important steps in quality manufacturing or metal finishing. Plenty of low cost, good quality water for rinsing has been available in the past, so rinse water conservation has been largely ignored. Today, this is no longer true. Tap water costs have increased dramatically. Various new regulations are now in effect which limit the allowable volume of wastewater. Others require wastewater treatment. Still other laws tax the amount of water going down the sewer. These factors have all encouraged many manufacturers and platers to invest in automatic rinse tank control systems. Many platers using automatic control systems for the first time are pleased to discover a reduction in water usage of up to 80%.

    By Myron L Company Distributor in ALASKA (USA).

  • Premium

    Sewer flushing for the wastewater industry

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Sewer flushing for municipalities

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Sewer cleaning for the wastewater industry

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Sewer cleaning for municipalities

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Fly Ash - Industrial Vacuum

    Fly Ash can cause many problems. The Vac-Con & Vector Pneumatic Vacuum systems can assist and solve many of these problems. Our high-performance vacuum systems are manufactured in three basic configurations: Truck mounted, Trailer mounted, and Fixed/static installed. Any of these systems can be integrated into the existing power plant design. All of our vacuum systems can be utilized to solve your plant’s fly ash removal/clean-up needs and can assist in many other maintenance projects. All can be tailored to fit into your power plant’s specific needs. Vac-Con Truck mounted Industrial vacuum systems are equipped with large storage debris tanks with self-cleaning intake filter systems. The Industrial Trucks vacuum the waste products through existing manifold piping or with hoses attached directly to the debris tank. When fully loaded, the truck can then drive directly to the disposal site and discharge the waste products. The Industrial Truck offers a great amount of flexibility of operation and can be utilized anywhere in your facility for many different types of normal and emergency maintenance operations. The Vac-Con Industrial Vacuum Truck can be utilized on both wet and dry materials. The same Vac-Con truck can be used for removing Fly Ash from your plant, coal from broken intake belt conveyors, or used to suck wet muddy material from storage lagoons. The Vector Trailer mounted Vacuum Systems are designed to be used in several locations around power plants. The Trailer mounted Vacuum Systems connect to Manifold piping located in key areas within your power plant. The Vacuum systems move the waste products from the plant and deposit these products into moveable storage containers. The loaded storage containers when full can then be moved to the disposal sites for discharge. Vector Static Mounted Vacuum systems are designed to vacuum and remove Fly Ash and other bulk waste products through manifold piping from operational areas of the plant and deposit these waste products into collection storage silos for later transport to disposal sites. The fixed vacuum systems are electric motor driven and are normally installed as a permanent addition to in-plant existing conveying systems. Please contact us with any requirements you may have. We will evaluate your request and respond with solutions specific to solve your problems and fit your needs.

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Hydro excavation for refineries

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Industrial vacuuming for power generating plants

    By Vac-Con, Inc. Distributor in ALASKA (USA).

  • Premium

    Cleaning process for water intake

    By Acme Engineering Prod. Ltd. Distributor in Anchorage, ALASKA (USA).

  • Premium

    Erosion Control

    For more than 80 years, FINN has been providing quality equipment to the landscape and erosion control industries and is your number one solution for erosion control compliance. Our machines are known for productivity, reliability, and long lasting product performance. Our company is known for innovation, dependability, and industry leading product support. Only FINN provides the widest variety of HydroSeeder® sizes ranging from 300-4,000 gallon capacities, has an exclusive pump designed to handle the thickest slurries, and offers numerous options to provide for a more powerful and operator-friendly HydroSeeder®, all while keeping maintenance costs low. With the addition of a FINN Bark & Mulch Blower and a FINN Straw Blower, you'll own the machines necessary to fulfill your commitment to good environmental stewardship.

    By FINN Corporation Distributor in ALASKA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you