Applications in New Mexico

  • Premium

    Reverse Osmosis Water Testing

    Osmosis is the phenomenon of lower dissolved solids in water passing through a semi-permeable membrane into higher dissolved solids water until a near equilibrium is reached. Reverse Osmosis (RO) is a membrane process of purification which removes most of the the total dissolved solids (TDS) in water by reversing the natural process of osmosis. Pressure is applied to a TDS-concentrated solution against a semi-permeable membrane, causing pure water to diffuse through the membrane. RO has become an important process for a wide variety of applications including: medical, laboratory, desalination, industrial wastewater, Deionized (Dl) pretreatment, and drinking water.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Deionized Water Testing

    Years ago, high purity water was used only in limited applications. Today, deionized (Dl) water has become an essential ingredient in hundreds of applications including: medical, laboratory, pharmaceutical, cosmetics, electronics manufacturing, food processing, plating, countless industrial processes, and even the final rinse at the local car wash.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Circuit Board Cleanliness Testing

    Contamination of circuit boards can bring about severe degradation of insulation resistance and dielectric strength. Cleanliness of completed circuit boards is, therefore, of vital interest. For those companies who have established circuit board cleaning procedures, the MIL Spec P-28809 has been used as a guideline for control. Now a simple `on line` test for the relative measurement of ionic contamination has been developed. This fast and economical method for testing circuit board cleanliness uses a Myron L Company Ultrameter II™ 4P or 6P, a suitable container, and a mixture of Dl (deionized) water and alcohol.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Boiler Water Testing / Cooling Tower Water Testing

    Boilers and cooling towers share two major water related problems: deposits and corrosion. As steam is generated by a boiler or water evaporating from a cooling tower, dissolved minerals are left behind, increasing the concentration of these minerals. Additional minerals are introduced via the water added to makeup the water lost to steam/evaporation. Eventually, the minerals reach a level (or cycle) of concentration that will cause either loss of efficiency due to scale or damage from corrosion. This level can be determined by the Ryznar or Langlier indices and correlated to a conductivity or TDS range. Most people recognize problems associated with corrosion. Effects from scale deposits, however, are equally important. For example, as little as 1/8` of scale can reduce the efficiency of a boiler by 18% or a cooling tower heat exchanger by 40%!

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Pool Water Testing / Spa Water Testing

    Anyone and everyone who is responsible for operating and maintaining a swimming pool or spa has to test, monitor, and control complex, interdependent chemical factors that affect the quality of water bathers are immersed in. Additionally, aquatic facilities operators must be familiar with all laws, regulations, and guidelines governing what these parameters should be.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Oxidation Reduction Potential (ORP)/Redox

    Oxidation Reduction Potential or Redox is the activity or strength of oxidizers and reducers in relation to their concentration. Oxidizers accept electrons, reducers lose electrons. Examples of oxidizers are: chlorine, hydrogen peroxide, bromine, ozone, and chlorine dioxide. Examples of reducers are sodium sulfite, sodium bisulfate and hydrogen sulfide. Like acidity and alkalinity, the increase of one is at the expense of the other.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Water Testing for Environmental Applications

    Keeping the water in our lakes, rivers, and streams clean requires monitoring of water quality at many points as it gradually makes its way from its source to our oceans. Over the years ever increasing environmental concerns and regulations have heightened the need for increased diligence and tighter restrictions on wastewater quality. Control of water pollution was once concerned mainly with treating wastewater before it was discharged from a manufacturing facility into the nation`s waterways. Today, in many cases, there are restrictions on wastewater that is discharged to city sewer systems or to other publicly owned treatment facilities. Many jurisdictions even restrict or regulate the runoff of stormwater — affecting not only industrial and commercial land, but also residential properties as well.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Water Testing for Horticulture

    Modern growing practices include scientific evaluations of soil, water, fertilizers, diseases, etc. While some tests are best performed by a laboratory, others can be easily conducted on location, saving time and money. Three tests in particular, EC, pH, and ALKALINITY, can reveal valuable information about water quality, soil salinity, and fertilizer concentration. MyronL Company’s portable AGRI-METERS provide you with a simple, fast, and accurate means of testing these parameters.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Fountain Solutions

    Accurate fountain (dampening) solution concentration control is essential for consistent, high-quality results in lithography. Low concentration can cause drying on the non-image area of the plate resulting in tinting, scumming, blanket piling, etc. High concentrations, on the other hand, bring about over-emulsification of the ink. This results in weakening of color strength and changes in ink rheology (body and flow properties). Correct concentration will allow the non-image areas of the plate to be appropriately wetted.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Water Testing for Automatic Rinse Tank Controls

    Proper rinsing is one of the most important steps in quality manufacturing or metal finishing. Plenty of low cost, good quality water for rinsing has been available in the past, so rinse water conservation has been largely ignored. Today, this is no longer true. Tap water costs have increased dramatically. Various new regulations are now in effect which limit the allowable volume of wastewater. Others require wastewater treatment. Still other laws tax the amount of water going down the sewer. These factors have all encouraged many manufacturers and platers to invest in automatic rinse tank control systems. Many platers using automatic control systems for the first time are pleased to discover a reduction in water usage of up to 80%.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Water Testing for Textile Manufacturing

    The textile manufacturing industry encompasses many and diverse processes that rely heavily on the use of water, energy, chemicals, and other resources. Wet spinning, sizing, desizing, scouring, bleaching, mercerization, dyeing and printing are just a few. Monitoring and controlling the pH, TDS/Conductivity/Salt Concentration, ORP (REDOX), and Temperature of the aqueous solutions used in these processes conserves costly resources, controls quality, and reduces the amount of pollution that must be treated before discharge of effluent wastes. This can be done manually with handheld instruments or automatically with in-line monitor/controllers.

    By Myron L Company Distributor in NEW MEXICO (USA).

  • Premium

    Dosing pumps for water and wastewater treatment industry

    Peristaltic pumps are proven performers in water and waste treatment solving problems including: Dosing and metering treatment chemicals and reagents including ferric chloride (“Ferric”), sodium hypochlorite (“Hypo”), chlorine water, lime (Kalic or Kalkmilch), caustic soda, powder activated carbon and polymers, sludge transfer, filter press feeds.

  • Premium

    Accurate ink dosing pumps in printing and packaging

    Verderflex peristaltic pumps offer optimum performance to the printing and packaging industries. Combining the ability to self prime, run dry and an ultra fast tube changeover these pumps keep downtime to an absolute minimum. Additionally, the combination of the simple tube clamping mechanism and the low tube cost generates savings in by eliminating specialist tools and labour and by costly cleaning cycles.

  • Premium

    Hygienic, food grade tube and hose pumps and food pumps

    Food products such as dairy, baked goods, cereals, beverages and confectionary demand pumps that meet today’s hygiene standards and are able to handle products with care. Peristaltic tube pumps are perfect for sanitary pumping of many foods and liquids. The gentle pumping action works well with shear sensitive products and products that offgas, such as when pumping yeast in brewing beer.

  • Premium

    Chemical resistant dosing pumps

    Verderflex tube pumps provide precision pumping and dispensing solutions for the pharmaceutical industry. The pumps range from simple manually variable pumps to versatile units with sophisticated dispensing profiles programs. Capable of speed, accuracy and the easy to use pump range are perfect for dispensing delicate, viscous, corrosive, shear sensitive or abrasive fluids.

  • Premium

    Panel mounted OEM pumps

    A large selection of panel mounted pumps and pump heads for use in Original Equipment Manufacture (OEM). These pumps are custom engineered to integrate within your own equipment whenever accurate and repeatable dosing or liquid transfer is a must. Pumps can be supplied with a range of power options including both A.C or D.C. motors.

  • Premium

    Chemical resistant dosing pumps for pharmaceuticals & laboratory industry

    Verderflex tube pumps provide precision pumping and dispensing solutions for the pharmaceutical industry. The pumps range from being manually operated to versatile units with sophisticated dosing programs. Capable of speed, accuracy and the easy to use pump range are perfect for dispensing delicate, viscous, corrosive, shear sensitive or abrasive fluids..

  • Premium

    Dosing pumps for anaerobic disgestion and biogas industry

    Biogas is a natural gas also known as biofuel or biomass and is produced by breaking down organic material such as household waste, manure and crops grown specifically for biofuel with temperature-sensitive microbes and capturing the by-products.

  • Premium

    Heavy duty slurry pumps for the mine industry

    Verderflex peristaltic pumps are the first choice for mines around the world, offering unrivalled performance in a tough and uncompromising environment. Abrasive mining slurries have sub-micron solid contents in excess of 80% with slurry SGs in excess of 2.0. Only hose pumps can pump such dense fluids whilst maintaining high levels of plant availability unlike centrifugal pumps which suffer from continuous downtime and are unable to pump such high SG slurries, lower plant performance Additionally, reversible hose pumps can be used to clear chokes in the thickener underflow line.

  • Premium

    Seal-Less Chemical Transfer And Metering Pumps

    When pumping hazardous chemicals it is important to use a leak free pump that resists the chemical’s corrosive effects.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you