Applications in South Carolina

  • Premium

    Reverse Osmosis Water Testing

    Osmosis is the phenomenon of lower dissolved solids in water passing through a semi-permeable membrane into higher dissolved solids water until a near equilibrium is reached. Reverse Osmosis (RO) is a membrane process of purification which removes most of the the total dissolved solids (TDS) in water by reversing the natural process of osmosis. Pressure is applied to a TDS-concentrated solution against a semi-permeable membrane, causing pure water to diffuse through the membrane. RO has become an important process for a wide variety of applications including: medical, laboratory, desalination, industrial wastewater, Deionized (Dl) pretreatment, and drinking water.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Deionized Water Testing

    Years ago, high purity water was used only in limited applications. Today, deionized (Dl) water has become an essential ingredient in hundreds of applications including: medical, laboratory, pharmaceutical, cosmetics, electronics manufacturing, food processing, plating, countless industrial processes, and even the final rinse at the local car wash.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Circuit Board Cleanliness Testing

    Contamination of circuit boards can bring about severe degradation of insulation resistance and dielectric strength. Cleanliness of completed circuit boards is, therefore, of vital interest. For those companies who have established circuit board cleaning procedures, the MIL Spec P-28809 has been used as a guideline for control. Now a simple `on line` test for the relative measurement of ionic contamination has been developed. This fast and economical method for testing circuit board cleanliness uses a Myron L Company Ultrameter II™ 4P or 6P, a suitable container, and a mixture of Dl (deionized) water and alcohol.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Boiler Water Testing / Cooling Tower Water Testing

    Boilers and cooling towers share two major water related problems: deposits and corrosion. As steam is generated by a boiler or water evaporating from a cooling tower, dissolved minerals are left behind, increasing the concentration of these minerals. Additional minerals are introduced via the water added to makeup the water lost to steam/evaporation. Eventually, the minerals reach a level (or cycle) of concentration that will cause either loss of efficiency due to scale or damage from corrosion. This level can be determined by the Ryznar or Langlier indices and correlated to a conductivity or TDS range. Most people recognize problems associated with corrosion. Effects from scale deposits, however, are equally important. For example, as little as 1/8` of scale can reduce the efficiency of a boiler by 18% or a cooling tower heat exchanger by 40%!

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Pool Water Testing / Spa Water Testing

    Anyone and everyone who is responsible for operating and maintaining a swimming pool or spa has to test, monitor, and control complex, interdependent chemical factors that affect the quality of water bathers are immersed in. Additionally, aquatic facilities operators must be familiar with all laws, regulations, and guidelines governing what these parameters should be.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Oxidation Reduction Potential (ORP)/Redox

    Oxidation Reduction Potential or Redox is the activity or strength of oxidizers and reducers in relation to their concentration. Oxidizers accept electrons, reducers lose electrons. Examples of oxidizers are: chlorine, hydrogen peroxide, bromine, ozone, and chlorine dioxide. Examples of reducers are sodium sulfite, sodium bisulfate and hydrogen sulfide. Like acidity and alkalinity, the increase of one is at the expense of the other.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Water Testing for Textile Manufacturing

    The textile manufacturing industry encompasses many and diverse processes that rely heavily on the use of water, energy, chemicals, and other resources. Wet spinning, sizing, desizing, scouring, bleaching, mercerization, dyeing and printing are just a few. Monitoring and controlling the pH, TDS/Conductivity/Salt Concentration, ORP (REDOX), and Temperature of the aqueous solutions used in these processes conserves costly resources, controls quality, and reduces the amount of pollution that must be treated before discharge of effluent wastes. This can be done manually with handheld instruments or automatically with in-line monitor/controllers.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Water Testing for Environmental Applications

    Keeping the water in our lakes, rivers, and streams clean requires monitoring of water quality at many points as it gradually makes its way from its source to our oceans. Over the years ever increasing environmental concerns and regulations have heightened the need for increased diligence and tighter restrictions on wastewater quality. Control of water pollution was once concerned mainly with treating wastewater before it was discharged from a manufacturing facility into the nation`s waterways. Today, in many cases, there are restrictions on wastewater that is discharged to city sewer systems or to other publicly owned treatment facilities. Many jurisdictions even restrict or regulate the runoff of stormwater — affecting not only industrial and commercial land, but also residential properties as well.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Water Testing for Horticulture

    Modern growing practices include scientific evaluations of soil, water, fertilizers, diseases, etc. While some tests are best performed by a laboratory, others can be easily conducted on location, saving time and money. Three tests in particular, EC, pH, and ALKALINITY, can reveal valuable information about water quality, soil salinity, and fertilizer concentration. MyronL Company’s portable AGRI-METERS provide you with a simple, fast, and accurate means of testing these parameters.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Fountain Solutions

    Accurate fountain (dampening) solution concentration control is essential for consistent, high-quality results in lithography. Low concentration can cause drying on the non-image area of the plate resulting in tinting, scumming, blanket piling, etc. High concentrations, on the other hand, bring about over-emulsification of the ink. This results in weakening of color strength and changes in ink rheology (body and flow properties). Correct concentration will allow the non-image areas of the plate to be appropriately wetted.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Water Testing for Automatic Rinse Tank Controls

    Proper rinsing is one of the most important steps in quality manufacturing or metal finishing. Plenty of low cost, good quality water for rinsing has been available in the past, so rinse water conservation has been largely ignored. Today, this is no longer true. Tap water costs have increased dramatically. Various new regulations are now in effect which limit the allowable volume of wastewater. Others require wastewater treatment. Still other laws tax the amount of water going down the sewer. These factors have all encouraged many manufacturers and platers to invest in automatic rinse tank control systems. Many platers using automatic control systems for the first time are pleased to discover a reduction in water usage of up to 80%.

    By Myron L Company Distributor in SOUTH CAROLINA (USA).

  • Premium

    Indoor air quality

    By Ahlstrom-Munksjö Office in Bethune, SOUTH CAROLINA (USA).

  • Premium

    Air monitoring for environmental control agencies

    Urban air pollution is a major environmental problem in the developing countries of the world. That`s why to monitor the air quality becomes fundamental to define the air pollution level and take important measures to improve the air quality.

    Ahlstrom offers a high performance filter media for Air Quality Monitoring. A filter media made of extremely pure micro-quartz fibers, appropriate for emission control at high temperatures and wherever absolute purity of the filter medium is required.

    By Ahlstrom-Munksjö Office in Bethune, SOUTH CAROLINA (USA).

  • Premium

    Air filtration for the automotive industry

    As a leader in automotive filtration applications, Ahlstrom has always been at the forefront of high-performance filter media.  Our Research and Development organization works hard to develop next generation products to meet the market needs for Air intake filtration.  Our air intake filter media range covers all market requirements from Heavy Duty and Automotive panel filter applications.    

     

    By Ahlstrom-Munksjö Office in Bethune, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for fiber production

    We deliver complete production lines or individual components for the recycling of packaging grades or fibers containing ink deposits for the wastepaper processing and recycled fiber production.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for chemical pulp production

    We deliver complete production lines or individual components for your pulp mill, including chemical recovery and the power island.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for the metals industry

    ANDRITZ METALS – highest quality in metalforming technology. Complete lines for the production and further processing of cold-rolled carbon steel, stainless steel, and non-ferrous metal strip. ANDRITZ METALS provides solutions for lines to produce steel and other metal strips. These lines consist of equipment for pickling, cold rolling, annealing, heat treatment, strip coating and finishing, and for pickling acid regeneration. Additionally, ANDRITZ METALS supplies turnkey industrial furnace systems for thermal processes, such as heat treatment of slabs and forged pieces, as well as refining furnaces for the copper industry. ANDRITZ METALS furthermore supplies presses for punching and deep drawing.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for the mining industry

    ANDRITZ capabilities for the minerals and mining industry. ANDRITZ gives you access to the latest technologies for solid/liquid separation, drying, and complete automation of individual systems or an entire plant. The systems are specifically designed for the most demanding applications and minerals & mining processing. The minerals and mining industries place unique demands on technology suppliers. Whether the application is for the mining and processing of fossil fuels, ores, precious metals, commodity metals, minerals, clays, coatings, sands/shale, or rare earth elements, ANDRITZ has products and solutions to improve production, efficiency, and end product quality.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for the nonwoven and textile industry

    ANDRITZ provides state-of-the-art nonwoven technology and textile technology for a great variety of applications. ANDRITZ supplies technologies for the nonwovens industry from forming to finishing as well as textile calenders. ANDRITZ combines the expertise of three leaders in the nonwovens and textile industries with long-standing and successful traditions: Asselin-Thibeau, Küsters, and Perfojet. The key competences lie in needlepunch, spunlace, wetlaid, wetlace, spunbond, spunjet, and finishing technologies. Customized concepts and services are developed to suit every need.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

  • Premium

    Recycling Solutions for the automation industry

    ANDRITZ AUTOMATION is a leading supplier of machines and plant control systems with 65 sites worldwide. ANDRITZ AUTOMATION makes your plant effective and economical: ANDRITZ AUTOMATION stands by your plant, starting with quotation engineering, project management, hardware and software engineering, to erection work, start-up and operator training, and continuing with maintenance and engineering work for expansions and improvements. With our plant control systems and simulation and advanced control tools, we help plants become operationally ready.

    By ANDRITZ MeWa GmbH Office in Spartanburg, SOUTH CAROLINA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you