burner valve Articles

  • Single-valve RTO Eliminates Odors and VOC

    Untitled Document Less expensive to purchase, ...

  • Comparative analysis of modern control and AI–based control for maintaining constant ambient temperature

    The objective of this paper is to study various control techniques in order to maintain constant ambient temperature by controlling the position of gas solenoid valve and expansion valve that control the volume of gas flow to the burner and volume of cool air flow into the room. In order to control the room temperature conventional P, PI, PID, model reference control (MRC), fuzzy logic control ...


    By Inderscience Publishers

  • Case study - How to properly maintain and service your oxidizer

    Your air pollution control system represents a significant investment in not only initial capital but also ongoing maintenance and operation. Routine inspections performed by your staff combined with thorough maintenance plans provided by Anguil Environmental Service Technicians will ensure you get the most from your investment over the entire life of the system. Anguil has almost three decades ...

  • Suspension Burning for Tire Fuel Optimization in Precalciner Cement Kilns

    Synopsis: A presentation on optimizing substitution rates of Tire Derived Fuel (TDF) in precalciner kilns using Suspension Burner technology.  Discussions will be made on the challenges faced by both preheater and precalciner kilns using TDF on the feed shelf, technical measures aimed at solving these limitations, achieving high TDF ...


    By AFS Technology

  • Dioxines and furanes - Case Study

    Example: Scrap copper recycling, cobalt for battery production Similar tasks: Metal recycling, roast processes, thermal waste disposal When recycling metals - as in scrap copper recycling (mostly cable material) - toxic waste gases often occur. The raw materials to be recycled are injected in a shaft kiln that emits dust, organic contaminants, carbon monoxide, dioxins as well as furans. A ...

  • Case study - Pemaco superfund site remediation

    OVERVIEW Pemaco was formerly a chemical facility located in a light industrial and residential area of Maywood, CA, adjacent to the Los Angeles River. No one knows how long hazardous substances had been leaking into the ground but the operations date back to the 1940's.  Up until closure of the facility in 1991, chlorinated solvents, aromatic solvents, and flammable liquids had ...

  • Update on the homeowner heating oil safety bill

    All homeowners in Massachusetts should be aware that on December 29, 2008, the State Senate enacted the long-awaited Homeowner Heating Oil Safety Bill as Chapter 453 of the Acts of 2008. It required homeowners to upgrade their existing oil heat supply line and insurance companies to offer coverage for a spill by July 1, 2010. On January 5, 2009, it was signed by the Governor. On June 30, 2010, a ...


    By Penney Engineering, Inc.

  • Maximizing Energy Recovery through Digester Gas Management System Enhancement

    ABSTRACTAdvanced anaerobic digestion practices and maximum energy recovery call for a digester gas system that reliably allows for complete biogas collection and utilization. This paper will describe the planning, design, and construction of a new digester gas management system at the East Bay Municipal Utility District’s (District) Main Wastewater Treatment Plant. The need for an upgraded ...

  • Additives mixing effect fuel consumption

    Additives are an instrument of fuel operational development properties which can’t be provided with the previous stages of fuel producing. They lead to product correction, instead of participate in the main method of production. Their efficiency is caused by chemical structure, structure of a basic base, mutual influence and additives mixing process. Improvers which affect some parameters ...

  • Additives mixing effect fuel consumption

    Additives are an instrument of fuel operational development properties which can’t be provided with the previous stages of fuel producing. They lead to product correction, instead of participate in the main method of production. Their efficiency is caused by chemical structure, structure of a basic base, mutual influence and additives mixing process. Improvers which affect some parameters ...

  • Minimizing Operating Costs in VOC Abatement Equipment

    Untitled Document As governmental regulations of environmental emissions become more restrictive, the average concentration of Volatile Organic Compounds (VOC's) has decreased as more ...

  • Case study - RTOs leave nothing to HAP-penstance

    PROBLEM The United States EPA promulgated a ruling in 40 CFR, imposing strict new standards to reduce emissions of toxic air pollutants from the manufacture of pharmaceutical products, including prescription and over-the-counter drugs. The agency's rule was intended to reduce emissions of a number of air toxins and hazardous air pollutants (HAPs), including methylene chloride, ...

  • Flexographic printer system repair - Case study

    A flexographic printer recently contacted Catalytic Products International for help solving a recurring problem with competitors Regenerative Thermal Oxidizer (RTO) that was purchased two years earlier. The system had never been able to pass a stack test; the company was out of compliance and running out of time with the state EPA.  Any calls for assistance in getting the RTO to be compliant ...

  • Metal Coating Emission Control

    The use of regenerative thermal oxidizers is expanding into applications where they wouldn’t have been considered years ago, says Mike Scholz As the first generation of oxidizer systems in the industry nears the end of their service life, many canmaking plants face repair or replacement of their existing air pollution control systems. Like many others in the industry, a Silgan canmaking ...

  • Case study - RTO handles high VOC loading at silgan containers

    OVERVIEW Regeneration Game - Originally printed in The Canmaker Magazine - Sayers Publishing Group As the first generation of oxidizer systems in the industry nears the end of their service life, many canmaking plants face repair or replacement of their existing air pollution control systems. Like many others in the industry, a Silgan canmaking plant in the ...

  • Case study - Flexographic printer: efficient emissions

    Problem Control of air emissions has become an important issue that flexible packaging converters must consider when changing or upgrading equipment. Robbie Manufacturing of Lenexa, KS, a producer of printed shrink films, bags and pouches for a diverse range of applications, addressed its emissions in 1991 and 1996 by investing in two catalytic oxidizers to control the EPA-regulated air ...

  • Case study - RTO: Efficient emission - Working with your pollution control equipment supplier can lead to reductions in both emissions and operating cost

    Untitled Document Robbie Manufacturing of Lenexa , KS is a leader in the production of printed shrink films, bags and pouches for a diverse range of demanding applications. In 2004 alone, the company was awarded a Good Buy award from Good Housekeeping magazine, achieved rigorous American Institute of Baking (AIB) certification and the highest award ( Best-in-Show for Wide Web ) possible from the ...

  • Case study - Meat processing odor control

    Overview For its first two years of production, a food manufacturer based in South Wales, England, focused its production on potatoes. Neighborhood residents voiced no complaints about odors during this time period. However, as new production lines (including barbequed meats and curried chicken) were added, the complaints began, and it became clear that odor abatement equipment was needed ...

  • Case study - Printing: Flexographic

    Problem A flexographic converter needed to expand its business by adding an 8-color CI printing press to its existing press lines, and planned to add a second press later. The increase in emissions and flow from the new press was beyond the capacity of the existing 10-year old catalytic oxidizer. The customer needed a way to maintain compliance at an affordable cost. ...

  • Case study - Printing: RTO solution

    Overview A flexographic converter needed to expand its business by adding an 8-color CI printing press to its existing press lines, and planned to add a second press later. The increase in emissions and flow from the new press was beyond the capacity of the existing 10-year old catalytic oxidizer. The customer needed a way to maintain compliance at an affordable cost. ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you