analyzer manufacturer Articles

  • Request from the Laboratory in an Oil Refinery to Testing and Analyzing Equipment Manufacturers

    Oil refineries are always required, as social duties, to strictly ensure "safety" and appropriately manage "environment, health and quality" and "stable supply" and, as economic duties, to seek and manage "productivity." The mission of the laboratory of the oil refinery is to support good management, and it is essential for the laboratory to select and manage appropriate testing and analyzing ...


    By HORIBA Europe GmbH

  • Manufacturers face challenges with pharmaceutical impurities

    Pharmaceutical manufacturers may face various challenges when attempting to meet the United States Pharmacopeia (USP) requirements for residual solvents (volatile organic chemicals).Residual solvents in pharmaceuticals are trace level impurities of volatile organic compounds in final products or excipients. In general, residual solvents originate from manufacturing processes related to the ...


  • Recuperative oxidizer - Boat engine manufacturer

    Epcon has extensive experience in designing and building Thermal Oxidizers for Engine Cell Testing. The Problem A major Boat Engine manufacturer needed to lower emissions from engine cell testing. All motors, whether automobile or boat, are Pre-Tested for several hours prior to shipping. The emissions from these Engine Cells are mostly Carbon Monoxide and unburned fuel, with ...


    By Epcon Industrial Systems, LP

  • Research NOx Analyzers

    ECO PHYSICS provides environmental experts with exceptionally sensitive and precise NOx measurement instruments. Please take a look at our newest press release on our research NOx analyzers below. Bound by the same laws of nature, ecology and physics are close associates in an on-going battle to preserve air quality around the globe. One of our planet's champions is Swiss-based ECO PHYSICS. The ...


    By ECO PHYSICS INC.

  • Case study - Batch chemical manufacturing

    Location: New Jersey Equipment: Refurbished, warranted Regenerative thermal oxidizer RTO; (10,000 scfm) (1994 vintage) Installed: 2002 Problem: Batch chemical manufacturer required emission controls as part of a process expansion in their New Jersey facility. Project Details: ...


    By Kono Kogs, Inc.

  • Actio at tip of the green manufacturing revolution

    What began as an idea in a technology clean room has evolved into a globally-sought software platform system for the modern, environmentally-regulated marketplace. Actio Corp. was co-founded in 1996 by former college classmates — Russ McCann, a veteran high-tech entrepreneur from Silicon Valley, and Kal Kawar, a chemical engineer and industrial hygiene expert. McCann said the company was ...


    By Actio Corporation

  • Real Time Measurments of Acetylene in Ethylene Manufacturing Process

    Keywords Tunable Diode Laser, Wavelength Modulation Spectroscopy, Analyzer, Acetylene, Ethylene, Acetylene Converter Abstract The analyzer, based on near infrared Tunable Diode Laser Absorption Spectroscopy (TDLAS), was developed for the measurement of acetylene in process streams. Measurements of acetylene were made as under laboratory conditions and in ...

  • The Quality of the Manufactured Bread and Hygienic Conditions of Bakeries

    ABSTRACT In Iran and the countries of the Eastern Mediterranean Region, bread has always been considered as the staple food of choice. Because of having high quantities of minerals and vitamins in bread, the hygienic condition of its production is of prime importance. This cross-sectional study was conducted in 302 bakeries in Kerman city, Kerman Province, Iran, from April 2004 to March 2005. ...

  • Magnetic filtration used in a candy manufacturing plant

    Candy ManufacturerPt. Mayora Indah Tbk.IndonesiaPROBLEM: High levels of finished product being rejected due to ferrous contamination.SOLUTION: Beny Hermawan of PT. Sinarmentari Indoprima the Indonesia distributor for OEI installed an OEI magnetic filter rod (3RNC5812) in an existing T-Strainer on the finished product line (photo A).RESULTS: Photo B: contamination captured 44 grams ...


  • Integrated Engineers Case Study: Circuit Board Manufacturer

    A circuit board manufacturer in southern California was not able to achieve the discharge levels of copper and nickel with their existing system of coagulant, anionic and cationic flocculants and metal precipitant treatment process followed by lamella plate clarification. The previous treatment process developed a settled sludge that had poor shear characteristics and required further coagulant ...


    By Integrated Engineers Inc.

  • How LIMS Facilitates Lean Manufacturing Processes in the Laboratory

    (Reprinted from American Laboratory September 2006)   Despite the well-documented success of lean manufacturing in the past decades, by and large, laboratories have been slow to adopt lean manufacturing principles to help ...


    By STARLIMS Corporation

  • Oxidizer Media Replacement Restores Performance for Containers-Manufacture

    Operating Issue A manufacturer of metal containers encountered major operating problems with their Eisenmann 40,000 SCFM Regenerative Thermal Oxidizer (RTO) that hindered their production performance and caused major concern regarding an upcoming air compliance test. The overall pressure drop across the system was high and the pressure imbalances negatively impacted their process ...


    By Pollution Systems

  • Analyzing for Trace CO and CO2 using a Total Hydrocarbon Analyzer

    Untitled Document The purity of Specialty Gases is determined by the measurement of various contaminants including Total Hydrocarbons. Low level measurements of carbon ...


    By AMETEK MOCON - Baseline

  • Chocolate, Candy and Snack Cake Manufacturer - Case Study

    A world renowned sweets manufacturer located just outside the heart of a major city in Mexico, produces sweet marshmallow chocolate-covered products. Faced with space limitations and increased discharge regulations, this processor needed to find a primary wastewater treatment system that would solve their regulatory issues, be expandable for the ever-growing company and fit within a small ...

  • Sewer Cleaning Hose Cover analyzed for effectiveness.

    Sewer cleaning hose covers look pretty much the same. But there are big differences which are not visually apparent to the human eye. A hose produced by one specific manufacturer may appear to have a thick cover, but this is very misleading.  This is due a large diameter filament “open braid” which this manufacturer uses on top of the normal braid.  This large diameter open ...


    By Dyna Flex Inc.

  • Monitoring Air/Fuel Mixtures in Glass and Glass Fiber Manufacturing case study

    Measurement of Premix Gas. To produce the desired flame in a glass forehearth or when making fiberglass (glass fiber) insulation, an air/fuel pre-mixer is used. The pre-mixer combines compressed natural gas or propane with air and this mixture is then piped to the process burners At the burner, a fuelrich or fuel-lean flame is produced depending on the air/ fuel ratio selected. In many ...

  • Oxygen detection in manufacturing of precious and non-precious metal coins - Case Study

    Oxygen detection in heat treating/annealing furnace atmosphere in manufacturing of precious and non-precious metal coins Sunshine Minting use the Systech Illinois EC913 process oxygen analyzer to monitor the oxygen in their heat treating/annealing furnace attmosphere. Based in Idaho, U.S.A., Sunshine Minting Inc. (SMI) is a leading supplier of precious metal and base metal mint products. ...


    By Systech Instruments Ltd

  • Portable lead analyzer to locate source of lead

    OBJECTIVE: To investigate the sources of lead in the environment in children with elevated blood, with the help of a Field Portable X-Ray ...

  • Making manufacturing more sustainable - Subcommittee E60.13 lays groundwork for standards

    A new ASTM International subcommittee has begun work on standards that address sustainable manufacturing. Sometimes zero is not zero. Case in point: Manufacturer X sends no byproducts or waste to landfills or to incinerators. Manufacturer Y doesn’t dump waste in landfills, yet it does opt to burn refuse for energy. Both claim they have “zero landfill” programs. ...


    By ASTM International

  • Global aerospace manufacturer cuts material-approval time by 75%

    Automating workflows around today’s detailed materials data gets planes off the ground quicker, according to Actio. The aerospace industry is known for inventing, driving, and implementing advanced technology to solve complex engineering problems. Processes are implemented throughout design and manufacturing to ensure that chemicals, parts, and systems: comply with design ...


    By Actio Corporation

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you