astm d7066-04 Articles

  • Part 75 Conformance - Is your AETB ASTM D7036 Accredited?

    We have reviewed 2012 EPA Part 75 test reports and discussed EPA’s electronic reporting and source tester requirements with Part 75 source owners.  We conclude that many owners and environmental specialists who enter test data into EPA data bases are not familiar with the range of EPA’s expectations for source tester (Air Emission Testing Body or AETB) conformance to ...


    By Golden Specialty, Inc.

  • New ASTM Test Method Offers Quick and Easy Oil and Grease Measurement for Water and Soil Samples

    Onsite Field Measurement of Oil and Grease A quick and easy field analysis method for determining oil and grease concentration levels is important for both offshore oil platforms and soil remediation sites.. Prior to the Montreal Protocol, infrared (IR) analysis using Freon as an extraction solvent was a widely used field and laboratory method. In 1999, the U.S. EPA promulgated Method 1664A ...


    By Spectro Scientific

  • A Promising Future for Butanol

    With several beneficial attributes that make it a good blending agent in gasoline, butanol continues to hold promise for use as a biofuel. It is compatible with existing vehicles and refueling infrastructure. Low vapor pressure, high octane number and favorable distillation properties all add to the high blending value of butanol. Now, a new ASTM International standard will be used in isobutanol ...


    By ASTM International

  • Comply with Permit Levels for Fats, Oil and Grease in Wastewater using Portable IR Analyzers

    Wilks InfraCal TOG/TPH Analyzers provide accurate, on-site analysis to help regulators and industry reduce the discharge of fats, oil and grease in wastewater.  On-site testing with the portable mid-IR InfraCal Analyzer gives results in 10 minutes and eliminates the wait for off-site lab results.  It is simple enough for an operator with minimal training to do the analysis. Stricter ...


    By Spectro Scientific

  • Accurately Measure Hydrocarbon (Oil/Grease) Levels in Produced Water in Under 15 Minutes

    Determining total hydrocarbon or oil/grease levels to ensure compliance with regulatory permit requirements for discharging produced water is a worldwide problem facing the oil and gas industry.   Ensuring compliance with these regulations and avoiding fines for non-compliant discharges requires more frequent wastewater measurements to determine the total hydrocarbon ...


    By Spectro Scientific

  • Combating Corrosion - Committee G01 Standards Fight Nature’s Destructive Tendencies

    The evening news may leave many of us feeling war-weary, but one ASTM International technical committee has been successful in conflict of a different sort. It’s a commonplace but epic struggle between the natural and civilized worlds — the fight against metal corrosion. For the past half-century, the weapon of choice of ASTM Committee ...


    By ASTM International

  • State-of-the-art applications of the pull-off test in civil engineering

    In 1974, the concept of using pull-off test as a means of predicting the compressive strength of concrete was patented in the UK by Professor Long at Queen's University Belfast. Initially, the pull-off test was developed primarily aiming at unplanned in-situ strength determination. It was found later also particularly suited for assessment of bond strength of repairs. This test has now been ...


    By Inderscience Publishers

  • Rapid on-site analysis of fats, oil and grease (FOG)

    It is estimated that 23-28% of Sanitary Sewer Overflows (SSOs) are due to Fats, Oils and Grease (FOG) or as much as 19 million gallons from 1998 to 2001 (State of North Carolina, 2004). Our increasingly mobile society has led to a decrease of cooking at home and a significant growth in the commercial food sector. This, on top of other industries such as metal processors, meat packers, cosmetic ...


    By Spectro Scientific

  • Taking Fossil Fuels to the Next Level - Standards Underpin Extraction, Processing and Distribution

    To the average person, the oil and gas industry may appear simple — a matter of literally tapping into a natural resource and distributing it to customers. Of course the matter of extraction is rarely simple, and in the case of emergent hydraulic fracturing technology, it is particularly complex and capital-intensive. In fact, the world of petroleum and natural gas extraction, distribution ...


    By ASTM International

  • Impact of Corrosion on Electronic Equipment

    Corrosion is the destruction of metals through reaction with compounds in their environment. It is a natural process because compounds such as oxides, sulphides and chlorides are formed and these are stabler than pure metals. Electronic circuits and components are omnipresent in our environment. Until recently, the thousands of soldered joints that an electronic circuit contains were ...


    By Bioconservacion SA

  • Sample Handling Strategies for Accurate Lead-In-Soil Measurements in the Field and Laboratory

    ABSTRACT The inhomogenous lead-in-soil matrix can present serious obstacles to accurate sample collection and handling. In typical lead-in-soil measurement, particle size related errors in sampling and sample handling often exceed all other sources of error. The magnitude of error can vary widely depending on the particulate nature of the lead contaminant and the effectiveness of control ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you