burner manufacturer Articles

  • Burner Efficiency

    The Customer The Company is a world leader in combustion technology. They design and manufacture burners for residential, commercial and industrial applications. The Process After the burners have been manufactured they must be tested to meet the standards of BTS-2000. This standard specifies the methods procedures for determining the performance and ...

  • WIRAJASA Waste Oil Burner

    Brief description on our patented Waste Oil Burner that was introduced in 2008. This innovative device works on two key principles namely pre-heating of waste oil and application of super-heated water or sub-critical steam to enhance the oxidation of heavy oil. Heating capacity of this burner is adjustable starting from 700,000 BTU/hour to 1,400,000 BTU/hour is suitable for various thermal ...


    By CV Wirajasa Teknik Industri

  • Low-Nox Burner retrofit Experiences in Cracking Furnaces at Dow, Terneuzen

    Abstract: Dow Benelux B.V. (Dow) operates three ethylene plants from the Netherlands, all based within its Terneuzen facility. In 2009, Technip Stone & Webster Process Technology (Technip) studied options to reduce the NOx emissions from the cracking furnaces of cracker 1. The results of this study, combined with the experience elsewhere within the Dow Chemical Company, have been used to ...

  • Direct fired thermal oxidizer - Aluminum manufacturer

    Epcon has extensive experience in designing and building Air Pollution Control Systems for the Aluminum Industry. The Problem The company had a direct fired afterburner and a gas fired rotary kiln. The kiln would de-oil the aluminum scrap and the offgas would go to the afterburner. The design of the system was over 20 years old and very fuel ineffficient.   ...


    By Epcon Industrial Systems, LP

  • Monitoring Air/Fuel Mixtures in Glass and Glass Fiber Manufacturing case study

    Measurement of Premix Gas. To produce the desired flame in a glass forehearth or when making fiberglass (glass fiber) insulation, an air/fuel pre-mixer is used. The pre-mixer combines compressed natural gas or propane with air and this mixture is then piped to the process burners At the burner, a fuelrich or fuel-lean flame is produced depending on the air/ fuel ratio selected. In many ...

  • Case study - Automotive manufacturer chooses the QUADRANT SR Thermal Oxidizer

    The worlds largest automotive manufacturer recently installed our QUADRANT SR-Series Thermal Oxidizer for use at destroying CO and VOC emissions from their engine test cell facility. The test facility houses several engine, transmission, and chassis dynamometer’s. The manufacturer demanded a system that would provide the highest uptime reliability and highest performance. The QUADRANT ...

  • Waste-to-energy in Indonesia

    Brief description on Waste-to-energy technologies and particular equipment that the company has designed and manufactured. CV Wirajasa Teknik Industri is offering Waste Oil Burner and Biomass Combustion to replace conventional burners that utilize fossil fuel such as natural oil, synthetic lubricating oil, Biomass Combustion Chambers can be applied in sereal and nut drying, organic fertilizers ...


    By CV Wirajasa Teknik Industri

  • Case study - Landfill waste gas abatement

    For over 43 years Catalytic Products International has designed and manufactured specialized oxidation systems for use in controlling process-related VOC emissions. The QUADRANT-NRV Series Thermal Oxidation System is designed for use with the low-volume/high-BTU waste gas stream emitted from many landfill gas purification processes. As we utilize our Venturi Burner Package to process the waste ...

  • `Must Do` Waste Oil Furnance Maintenance

    Recommendations to keep your waste oil burner running at peak performance and resistant to mechanical issues, including a list of typical standard maintenance measures. Getting into a scheduled maintenance routine and making sure you're keeping your furnace running smoothly will keep it generating free heat for your business for many years to come. Failure to maintain your waste oil furnace ...

  • Exhaust Gas Treatment in Paint Shops: Volkswagen chooses catalytic afterburning

    Paint shops are an energy-intensive step in the automotive manufacturing process. One of the world´s largest paint-shop complexes is operated by the Volkswagen Group at its main plant in Wolfsburg. In the past VW used hot air from thermal afterburners to heat its paint dryers. Following a detailed review, the company was one of the first to decide to ...


    By Clariant International Ltd.

  • European Oil and Gas from Exploration to End User

    Made up of a team of senior specialists dedicated to innovation and dependability in the field of combustion technology; CS Combustion Solutions' (CS) staff use their 25 years of expertise in engineering, supplying and commissioning of vertical and horizontal combustors for a wide range of applications to find the best results for each individual requirement. "We are a company that specialises in ...

  • Saving waste in the boiler house

    Burner technology has improved greatly in recent years. Older Burners had a series of cams and levers that were calibrated to provide specific amounts of air for a particular rate of firing. Being mechanical items, these wore and sometimes required calibration. They, therefore, had to be regularly serviced and calibrated. Generally, new burners use frequency controlled motors and cams to open air ...


    By EBE Engineering Ltd.

  • What do a brewery and a wastewater treatment facility have in common? More than you think

    You may think that a brewery and a wastewater treatment facility are about as similar as day and night, hot and cold, old and young. But they have more in common than you think. ABUTEC has worked with both to ensure their waste-to-energy systems function at top capacity. Bell’s Brewery in Kalamazoo, Michigan, needed a way to save money, ensure compliance and practice sustainability. ...


    By ABUTEC LLC

  • Case study - Flexographic printer system repair

    A flexographic printer recently contacted Catalytic Products International for help solving a recurring problem with competitors Regenerative Thermal Oxidizer (RTO) that was purchased two years earlier. The system had never been able to pass a stack test; the company was out of compliance and running out of time with the state EPA.  Any calls for assistance in getting the RTO to be compliant ...

  • Wood waste case study - Jukes Holdings

    The MD of a group of independent coffin manufacturers has seen the light in recycling wood waste, and is saving thousands of pounds in waste disposal charges and heating costs by rolling out wood waste heaters across his companies. Stewart Jukes, MD of Jukes Holdings Ltd was so impressed with a wood waste heater purchased for one of his companies, Brian Reid & Son in Scotland, that he has ...


    By Wood Waste Technology Ltd

  • SOCAVER Thermal Gas Supply - Case Study

    SOCAVER (Société Camerounaise de Verrerie) is a subsidiary of the leading Cameroon brewery, SABC (Société Anonyme des Brasseries du Cameroun). SOCAVER, which is the only glass factory in the Central Africa region, blew its first bottle on 1 July 1970 and today supplies a host of African countries with its products. Specialising in the manufacture of hollow glass, ...


    By Victoria Oil & Gas Plc

  • Case study - How to properly maintain and service your oxidizer

    Your air pollution control system represents a significant investment in not only initial capital but also ongoing maintenance and operation. Routine inspections performed by your staff combined with thorough maintenance plans provided by Anguil Environmental Service Technicians will ensure you get the most from your investment over the entire life of the system. Anguil has almost three decades ...

  • Heat recovery and energy efficiency, improves profitability and reduces CO footprint

    Using latest technology in combustion of oil and gas can provide significant savings in overall energy consumption. Modern oxygen control that compensates changes in ambient temperature and fuel qualities can increase energy efficiency up to 3%. By adding the usage of hot combustion air another 2-3% can be saved. Modern burner technology without mechanical linkage, operating with accurate ...


    By Oilon Oy

  • Maxsys Fuel System generates 6% savings on Gas Fired Steam Raising Boilers at Mondi Packaging

    Mondi is one of the world’s leading international paper and packaging groups with a substantial global presence, employing 34,000 people at 112 sites across 34 different countries. The company is continually striving for a consistent high level of improvement in environmental performance in all its operations, making efficient use of raw materials and energy, while focusing on innovation ...


    By Maxsys Fuel Systems Ltd

  • Trailer Mounted Afterburner for Soil Remediation

    The Problem A major Vapor & Odor Control company needed a portable solution to clean the soil leftover at old fuel stations. The Process Soil Remediation Afterburners & Oxidizers are manufactured to treat soil containing contaminates such as petroleum hydrocarbons, with diesel oil, gasoline, aromatic hydrocarbons, solvents and many other ...


    By Epcon Industrial Systems, LP

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you