calibration gas kit Articles

  • A Guide to Gas Detector Tubes. Your Questions Answered

    Gas detector tubes are easy to use, are low cost, and the method is intrinsically safe, allowing it to be deployed in all industries. Because detector tubes don’t require calibration, users see the benefits of this technology over electronic gas detectors due to their ease of ...


    By a1-cbiss

  • Hydrogen Sulfide Continuous Emission Monitoring of Odor Control Systems

    ABSTRACT This paper discusses the use of the Sycamore Continuous Emissions Monitor (CEM) for monitoring Hydrogen Sulfide Gas concentrations within odor control systems. The CEM is configurable as a single, two or three point system and can measure from 5 ppb to 2 PPM, 0.1 – 20 PPM, and 0 – 200 PPM and is designed for monitoring of scrubbers, carbon adsorbers, biofilters and biotrickling ...

  • Field Detection of Chlorinated Alkenes in Well Water using the FROG-4000 Portable GC - Case Study

    Introduction Defiant’s FROG 4000, a portable GCPID system, was used to identify and determine the concentration of chlorinated alkenes in several extraction wells located in Tacoma Washington. Split samples were taken at each well and sent to an offsite lab for analysis. This case study examines the field exercise and highlights the high degree of agreement between the offsite lab and ...


    By Northern ANI Solutions Ltd.

  • Read about Confined Space in Construction and Atmospheric Testing Right Here!

    In 1993, 29 CFR 1910.146 went into effect as the first federal legislation governing entry into permit-required confined spaces in general industry. Because some industries, such as the construction industry, were covered by specific Occupational Safety and Health Administration (OSHA) safety regulations, they were exempt from the confined space entry requirements of the general industry rule. ...


    By Argus-Hazco

  • Determination of micro and macro elements in waters with the ELAN DRC-e

    The ability of reaction cell technology to reduce the effects of spectral interferences is well-known, but another, lesser-known capability also exists: extending the dynamic range. This is accomplished by adjusting the bandpass parameters with no gas in the cell. Because the bandpass parameters can be adjusted on a per-mass basis, sensitivity can be reduced on selected isotopes without affecting ...


    By PerkinElmer, Inc.

  • Compliance to standards in continuous emissions monitoring case study

    Customer: Glass Manufacturer Application: Continuous Emissions Monitoring Service (CEMS) for Glass Manufacturing Background: A glass factory is required to ...


    By Ecotech Pty Ltd

  • Case study - TPH Oil & Grease applications

    These case studies illustrate the performance generated from customers who have used Sitelab’s UVF-3100 analyzer for testing total petroleum hydrocarbons in the C10 to C50 range. Sitelab’s TPH-Oil calibration kit is designed to correlate well to laboratory “Oil and Grease” test methods. This includes EPA Methods 1664 and 9071B by Gravimetric, EPA Method 418.1 by Infrared ...


    By Sitelab Corporation

  • Analysis of Pesticides in Baby Foods Using a GCMS-TQ8030 GC/MS/MS, Part II

    Contamination of food products with pesticides is a growing concern because of recognized adverse health effects, increasing world-wide usage of pesticides, and increasing imports of raw foodstuffs from foreign sources. The concern is particularly acute for baby foods because of the high vulnerability of babies to health effects from synthetic chemicals such as pesticides. Gas chromatography ...

  • Case study - GRO in soil at gasoline UST site

    These case studies show the performance using Sitelab’s UVF-3100 analyzer testing gasoline range organic hydrocarbons.  This includes benzene, xylene, BTEX and other volatile petroleum compounds in the GRO or VPH C6 to C10 hydrocarbon range. When calibrated using Sitelab's GRO calibration kit (CAL-025), the UVF analyzer produces test results that correlate well to laboratory ...


    By Sitelab Corporation

  • Why instrument hire makes occupational safety sense

    Background Decisions concerning the acquisition of occupational safety monitoring instrumentation are often made by operational staff that may not have visibility of the full financial implications of their choices. The following article will examine the factors affecting these decisions and explain why a strategic decision to hire instrumentation can deliver substantial and wide-ranging ...


    By Ashtead Technology Ltd

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you