corrosion protection material Articles

  • Case study - Corrosion protection in a pulp and paper industry

    It is widely accepted that corrosion has an important economic impact at an industrial scale. As an example, results of a study carried out in the US showed that the total annual estimated direct cost of corrosion in the country was $276 billion, which was approximately 3.1% of the nation’s Gross Domestic Product (GDP). Thus, within the last few decades, an important effort has been made to ...


    By Bioconservacion SA

  • Corrosion protection with synergistic LBL/Ormosil nanostructured thin films

    Stratified systems comprising an inhibitor-doped layer-by-layer (LBL) clay-polyelectrolyte overcoated with a dense organically-modified silicate (Ormosil) are investigated as corrosion protectors for aluminium. As separate coatings, neither the LBL nor Ormosil films were found to provide adequate corrosion protection of the underlying metal. A combination of the two coating methods was found to ...


    By Inderscience Publishers

  • Polymer Concrete for Structural Restoration and Corrosion Protection of Concrete Support Columns

    Introduction A large copper mine and refinery in the western United States had a dilemma. Their cell house, which contains over 1,500 cells, each holding more than 20,000 gallons of electrolyte, had experienced severe corrosion and structural degradation of the support columns for the tanks. These columns support the cells in their solvent extraction and electrowinning process. This ...


    By Sauereisen Inc.

  • Monitor Hull Corrosion with Thickness Gauge

    After our recent article about inspecting your hull paint to reduce bio-fouling and acting as an anti-corrosion method, we wanted to delve deeper into one of the biggest problems shipowners and operators face: corrosion. ...


    By Deep Trekker Inc.

  • Protective Coatings

    Coatings An industrial coatings is a paint or coating defined by its protective, rather than its aesthetic ...


    By Ultimate Linings

  • Combating Corrosion within Power Generation Facilities

    Just about every utility facility that generates power or engages in some form of incineration must deal with corrosion issues. Since the ac Air Act of 1990, gas-scrubbing technologics have increased the im serving the assets of power plants and othe incineration infrastructure. These demands will increase further with the advent of new mercury removal requirements to be phased in during e near ...


    By Sauereisen Inc.

  • Combating Corrosion - Committee G01 Standards Fight Nature’s Destructive Tendencies

    The evening news may leave many of us feeling war-weary, but one ASTM International technical committee has been successful in conflict of a different sort. It’s a commonplace but epic struggle between the natural and civilized worlds — the fight against metal corrosion. For the past half-century, the weapon of choice of ASTM Committee ...


    By ASTM International

  • Assessment of material deterioration in Bulgaria owing to air pollution

    Atmospheric pollution is an important factor in material deterioration, including degradation of systems used for material protection. Owing to pollution, the lifetime of technological products is shortened. Buildings and other structures, as well as objects of cultural heritage exposed to the atmosphere, deteriorate more rapidly. The resulting physicochemical and economic damage can be ...


    By Inderscience Publishers

  • Ultimate Linings Best| Industrial Coatings| Protective Coatings

    Industrial coatings are generally used to diminish the effects of corrosion thus preventing the metal from being tarnished or damaged. Industrial protective coating enhances the finesse of the metal or material which in turn improves the quality. The ...


    By Ultimate Linings

  • Selecting and Placing Gas Detectors for Maximum Application Protection

    Many industrial processes involve dangerous gases and vapors: flammable, toxic, or both. With the different sensing technologies available, and the wide range of industrial applications that exist, selecting the best sensor and locating them properly for the job at hand can be a challenge. To ensure a high level of safety, know the latest sensing technologies, which technology is best for the ...

  • Water Based Damp Course Protection Chemicals: Tech-Dry Building Protection Systems

     Tech-Dry Building Protection Systems Pty Ltd has developed a range of water-based damp course chemicals for the building industry. These water-based formulations have replaced the solvent-based formulations previously used by Tech-Dry. Background Tech-Dry Building Protection Systems Pty Ltd was formed in 1982, and specialises in the development and supply of materials ...


  • Dredge caustic and abrasive materials in South Korea-case study

    Customer: Zinc mining & processing facility, South Korea. Problem: How to remove 200,000 cubic meters of 325 mesh goethite (pH 2.2 - 2.5 range; sulfuric acid) from a lined pond with dimensions of 120m x 253m. Since the material had settled and was resting on the pond bottom, dredging was selected as the appropriate removal method. No standard acid-resistant dredge ...


    By SRS Crisafulli, Inc.

  • Synthesis and characterisation of nano silica-based coatings for protection of antique articles

    Antique articles are endangered by environmental effects such as humidity, UV and variation of temperature. Improved physical surface resistance is in an increasing demand in protection of cultural heritage. One possible way is their protection by suitable hydrophobic coatings. In this work, the experimentation of protective treatments on the soda glass, mud brick and copper, characteristic ...


    By Inderscience Publishers

  • Deal With The Pressure - Protect piping system components with Pulsation Dampeners

    Metering pumps with operating pressures of up to 150 psig (pounds per square inch gauge) can create unwanted pressure pulsations within a piping system – a real problem in applications such as filling, mixing and spraying that require a combination of a metering pump’s accuracy and a continuous flow. But the issue can often be addressed with Pulsation Dampeners.The Pulsation Dampeners, usually ...


    By Lutz-JESCO America Corp.

  • Two stainless steel rotomite applications - dredging caustic and abrasive materials in South Korea and Venezuela

    Customer: Zinc mining & processing facility, South Korea. Problem: How  to remove 200,000m3 of 325 mesh goethite (pH 2.2 - 2.5 range; sulfuric acid) from a lined pond with dimensions of 120m x 253m. Since the material had settled and was resting on the pond bottom, dredging was selected as the appropriate removal method. No standard acid-resistant dredge was in ...


    By SRS Crisafulli, Inc.

  • The Accidental Incident: Are you prepared in the event your company has a hazardous materials spill?

    Untitled Document Whenever a company stores hazardous substances and materials, there is always the potential for a spill. Taking precautions ...


    By 3E Company

  • Mild cleaning: removal of 900 kg iron from a cooling water system - within 7 hrs - Case Study

    A professional cooling water treatment prevents the plant from corrosion damages. But in case corrosion should occur, severe damages can be the consequence. The cooling system needs to be cleaned. In contrast to a conventional cleaning with aggressive acids, Kurita suggests an innovative cleaning method: mild, material-protective and effective.   With the mild Kurita cleaning method amazing ...


    By Kurita

  • Municipal Wastewater Pump Station Design Problems and Solutions

    The growth of the Northern Virginia Area around Washington D.C. has resulted in the requirement for numerous new wastewater pumping stations and the upgrade and expansion of existing pump stations. This paper presents practical problems and solutions associated with the following pump station design issues: 1.) Concrete Corrosion Protection, 2.) Corrosion Resistant Materials, 3.) Pump Protection ...

  • Case study - Industrial wastewater reuse: CEMEX UK

    CEMEX is one of the world's leading cement producers and suppliers of building materials. In order to limit their manufacturing footprint in terms of process water usage, CEMEX UK sourced their water from the final settlement lagoons of their local wastewater treatment plant (Anglian Water). atg UV Technology was approached by CEMEX UK to supply a containerized UV wastewater treatment plant to ...


    By atg UV Technology

  • Ethylene Plant Treatment Hydrocarbon Engineering

    Ethylene is the most commonly produced petrochemical product. The bulk of annual commercial ethylene production is based on thermal cracking of hydrocarbon feedstocks with steam. Usual raw materials for pyrolysis are refinery gas, liquid petroleum gas (LPG), natural gas liquids (NGL), naphtha or gas oil. The production of ethylene is a very complex process, including cracking, cooling, ...


    By Kurita

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you