dangerous gas alarm Articles

  • Gas safety in confined spaces

    A confined space is any space large enough for someone to enter and perform assigned work, which has limited means of entry or exit, and which is not designed for continuous worker occupancy. This covers just about every industry, including utilities, construction, hydrocarbon exploration and processing, petrochemicals, marine, agriculture, food processing and ...

  • Gas Safety in Confined Spaces

    Introduction A confined space is any space large enough for someone to enter and perform assigned work, which has limited means of entry or exit, and which is not designed for continuous worker occupancy. This covers just about every industry, including utilities, construction, hydrocarbon exploration and processing, petrochemicals, marine, agriculture, food processing and brewing, as ...

  • Gas Safety in Confined Spaces

    Introduction An offshore worker ensures a vessel is safe to enter; a plant manager enters a small plant room; a contractor inspects the lining of a sewage pipe.  All these personnel face common dangers, despite working in widely different industries.  Gas-related injury poses a serious threat in any confined space where the free movement of air is limited. A confined space ...

  • Gas safety in confined spaces

    An engineer repairs buried cables; a plant manager enters a small plant room; a contractor inspects the lining of a sewage pipe.  All these personnel face a common danger, despite working in widely different industries.  Gas-related injury poses a serious threat in any confined space where the free movement of air is limited.  ...

  • Compressed Gas Safety Guide

    Use and storage of any compressed gas under high pressure can be extremely dangerous if proper gas handling procedures are not observed. Moreover, chemical characteristics of specialty gases themselves can pose serious health hazards if containment is not tightly controlled. Paying close attention to a compressed gas product’s technical and safety information is invaluable for maintaining a safe, ...

  • Ammonia Vent Line Gas Detector

    The LPT-A Vent Line Ammonia Transmitter (P/N: LPT-A-VLT-NH3-S) is designed for continuous monitoring of ammonia levels in the vent lines of refrigeration systems caused by equipment failure or system over pressurization. Slow leaks of refrigerant can be costly over time and a dangerous situation could present itself if a high pressure release were to occur. The VLT provides continuous, ...

  • Monitoring flammable gas in boiler houses

    The most common fuels in use for space and water heating are Oil, Natural Gas and Liquid Petroleum Gas (LPG). By far the most popular, clean and cost effective solutions are utilising Natural Gas or LPG. The traditional safety measure derived from the time of oil fired boiler houses is the use of a fusible link placed above the each boiler. The fusible link is intended to melt if it becomes ...

  • Understanding the Benefits of Fixed Gas Detection

    "Fixed gas detection is an essential method of ensuring maximum protection for personnel and plant. There are a variety of technologies available for a multitude of applications. Understanding fixed gas detection is the first step in providing safety." What is fixed gas detection? Fixed gas detection is installed with the aim of providing continuous, area and personnel protection. ...


    By a1-cbiss

  • CO2 Gas Hazards in the Brewing Industry

    The hazards associated with CO2 in the brewing industry are well known, yet people still die needlessly every year in tragic and completely avoidable accidents in breweries. Just last year in Germany, which has a good safety record, two workers died in separate incidents at the same brewery. In the first incident, the owner was found dead with his head and torso in a beer mixing tank. It is ...

  • Gas detector communication technology for offshore oil and gas platforms

    In few applications is safety as important as on offshore oil and gas platforms. Explosive hazards from hydrocarbon gases and vapours are an ever-present risk, whilst toxic hydrogen sulphide gas and depleted oxygen environments can pose significant risks to personnel. Gas detectors are therefore essential to provide dependable early warning of gas hazards. Gas detectors are permanently installed ...

  • Chlorine Dioxide gas detection: A comprehensive guide

    Introduction Some years agoago, the bleaching process in the paper industry was changed from using Chlorine (Cl2) as bleaching agent to Chlorine dioxide (ClO2). This was a challenge forThis posed a major challenge to industrial hygienists, as there were no sensors or detectors available that were specific to Chlorine dioxide: There was no sensor technology for gas detectors available that ...

  • Selecting and Placing Gas Detectors for Maximum Application Protection

    Many industrial processes involve dangerous gases and vapors: flammable, toxic, or both. With the different sensing technologies available, and the wide range of industrial applications that exist, selecting the best sensor and locating them properly for the job at hand can be a challenge. To ensure a high level of safety, know the latest sensing technologies, which technology is best for the ...

  • Fixed Versus Portable Gas Detection – Which Is Better?

    Did you know that workers are needlessly injured every year as a result of leaking toxic or combustible substances? Such incidents are known to involve a wide range of hazardous gases (including ammonia, carbon monoxide, chlorine, hydrogen sulfide, hydrocarbon vapors and so on). The sad reality is that most of these accidents are avoidable if only the workplace is adequately monitored. This leads ...

  • Upgrading from Pellistor Gas Sensors to Infrared Technology

    In this article Andy Avenell, Crowcon’s Fixed Systems Product Manager, considers the shift towards infrared (IR) gas sensor technology in the oil and gas industry. Abstract Flammable gases and vapours can present considerable dangers in many industrial applications, none more so than the processes involved in extracting, transporting and processing oil and gas. Fast and reliable ...

  • Detecting Hydrogen Gas and Fires: Seeing the Unseen

    Hydrogen usage is growing. The general public sees and reads about hydrogen as an alternative fuel for cars. However, the big use for hydrogen is found in hydrocarbon processing and other important manufacturing processes. Hydrogen is the first element on the periodic table and is an essential element in the manufacturing of many of our everyday products. We must have respect for its explosive ...

  • Follow toxic gas standards for a smoother project

    Toxic gases, such as Hydrogen Sulfide and Sulfur Dioxide, can injure and kill quickly. Therefore, mitigation of these hazards must be fast and sure. The United States Occupational Safety and Health Administration (OSHA) and other authorities take detection of these gases very seriously. The American National Standards Institute/ American Petroleum Institute (ANSI/API) and ISA industry standards ...

  • PureAire Universal Gas Detector Offers Protection Against Toxic Levels of Ammonia

    In March of 2016, an ammonia gas leak at a seafood processing plant in Boston left one worker dead. The fumes at the plant were so powerful that firefighters could not promptly enter the scene to mitigate the gas leak and try to save the staff member until much later. Reports show that 5,300 pounds of ammonia gas leaked out of the plant. If you work with ammonia at your facility, learn ...

  • PureAire Combines Oxygen and CO2 Sensors to provide a Dual Gas Monitor to the Marketplace

    As a recognized leader in O2 safety monitoring, PureAire recently explored the need for an O2 monitor where carbon dioxide is used. There are four key cryogenic gases; nitrogen, helium, argon, and carbon dioxide (CO2), which can create an oxygen deficient atmosphere. Material Safety Data Sheets (MSDS) covering cryogenic gases cite that a cryogenic leak can create an unsafe ...

  • Safety Systems Depend on Reliable Field Sensors (Emphasis on Fire and Gas Detectors)

    Abstract Because not all hazards are the same, identifying and quantifying the hazard is the starting point in choosing sensing technology. Not all detectors are the same, and they should be selected according to their ability to detect the hazard. This paper gives a broad summary of technologies that provide users reliable responses to hazardous conditions, that minimise false ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you