dew point monitoring Articles

  • The Fatal Flaw in Dew Point Measurement for Injection Molding

    Dew-point measurement is a common and important metric in the plastic drying process. A good dew point meter can tell you whether your dryer is working normally or if it’s in need of repair. Dew point meters do this by measuring the humidity in the air that flows through the dryer. What dew point meters won’t tell you anything about, however, is how much moisture is actually present ...


    By Arizona Instrument LLC

  • Continous Emission Monitoring (CEMs)

    Presented in Track B1: CEMs at EUEC 2011,January 31 Phoenix, Arizona   B1.1  | Particulate CEM for wet FGD plant William Averdieck |  Managing ...

  • Sample System Best Practices for Water and Hydrocarbon DP Applications

    Abstract Sampling techniques for BTU and moisture measurements are well understood but applications beyond the routine requires additional attention to detail. Two such applications are the subject of this paper. The first is the measurement of low level moisture (1 – 1,000 ppbv) for cryogenic processes. Measuring moisture below 1 ppm is an entirely different world from the traditional ...

  • Thermal Patters Due to Moisture Accumulation within Exterior Walls

    In cold climates, air leakage is accompanied by moisture transport. When migrating through dew point temperatures, a considerable amount of moisture accumulation may occur depending on variables such as the duration of sub-zero exterior temperatures, building pressurization, wind effects and the level of interior relative humidity. Moisture accumulation may result in premature deterioration of ...

  • Heat treatment of steels and other metals case study

    Application Moisture is measured in the blanketing gases that are used in the treatment of steel. Problem Inert blanketing gases are required during the heat treatment of steels to prevent oxidation of the metal product. At heat-treating temperatures, moisture and oxygen will readily react with the metal to form an undesirable metal-oxide coating on the ...

  • Gill Instruments case study featured in AWE International

    AWE International magazine, which is focused on the environmental analysis industry, recently featured Gill Instruments in a case study about environmental monitoring with solid-state meteorological instruments. The case study includes information about all of the products within the Gill Instruments range, with information about their advantages within the environmental analysis field. We have ...


    By Gill Instruments Limited

  • Quality compressed breathing air really is a matter of life and death

    When some of the Analox team visited West Yorkshire Fire and Rescue Service it became even more apparent how important it is to undertake accurate and consistent checks on breathing apparatus. We were shown training facilities where firefighters are put in real-life situations in order to equip them with the experience to deal with whatever ...


    By Analox Sensor Technology

  • Case study - Destruction of inert process emissions

    Many chemical companies use batch reactors to make their products.  These reactors typically have vents which are opened and closed during emptying, filling, mixing, heating or cooling and other steps of the production process.  The gases coming from these vents must be controlled under most government regulations.  Generally speaking, the emissions produced are inert (little or no ...

  • Case study - Reactor vent emission control

    OVERVIEW Many chemical and petroleum companies use batch reactors to make their products.  These reactors typically have vents which are opened and closed during emptying, filling, mixing, heating or cooling and other steps of the production process.  The gases coming from these vents must be controlled under most government regulations.  Generally speaking, the ...

  • Saving waste in the boiler house

    Burner technology has improved greatly in recent years. Older Burners had a series of cams and levers that were calibrated to provide specific amounts of air for a particular rate of firing. Being mechanical items, these wore and sometimes required calibration. They, therefore, had to be regularly serviced and calibrated. Generally, new burners use frequency controlled motors and cams to open air ...


    By EBE Engineering Ltd.

  • The Role of Soil Moisture on our Climate, Weather and Global Warming

    Global warming is a topic that has received much attention in the media, especially during the hot days of summer. The process by which carbon dioxide (CO 2) in the atmosphere prevents the escape of thermal energy into outer space is known as the green house effect. The higher the carbon dioxide levels in the atmosphere the less thermal energy that can escape thus an increasing global ...

  • Case study - Oxidizer energy recovery options

    Overview The mainstream media today is full of allusions to energy awareness and conservation. Just as visible these days are media references to astronomical dollar figures that can boggle the mind. This article does not seek to break out of that mold, but rather to conform to it – as Oxidizer Stack Heat Recovery offers a tremendous opportunity for both energy conservation and ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you