differential pressure sensor Articles

  • Differential Pressure and Temperature Monitoring in a Hospital Cleanroom

    Accsense A1-01a Wireless Environmental Data Loggers CHESTERLAND OH—April 9, 2012 CAS DataLoggers recently provided the wireless pressure and temperature monitoring solution for a hospital maintaining a surgery cleanroom to protect patients from a variety of environmental contaminants. Staff entered and exited through airlocks and were required to wear cleanroom suits before entering. Air ...


    By CAS DATALOGGERS

  • When a pressure transmitter leaves the linearity: the Rosemount Case

    When a Rosemount pressure transmitter experiences the inner silicone oil-loss syndrome, it loses its linear behaviour. In such a case, the response time is not unique; as a consequence, focusing the sensor surveillance to the response time, as required by the technical specifications of the nuclear plant, might have no sense. In which way is the sensor dynamic not linear? Answering this open ...


    By Inderscience Publishers

  • A Multi-Sensor Piezometer for Shallow Marine Sediments in Coastal Environments

    A multi-sensor piezometer has been developed to measure dynamic excess and ambient pore pressures in shallow marine sediments under the effect of surface waves, tides, and currents. The probe consists of a shaft (1.5 m long with five porous stones at subseafloor depths ranging from 0.10 to 0.93 m) and two upper chambers (one that is hermetically sealed for the transducer electronics and another ...


    By ASTM International

  • Sensor design the key advantage in thermal mass flow meter performance

    Immersible thermal sensors arc finding growing acceptance in the gas flow measurement field. By using two Platinum Resistance Temperature Detectors (PRTDs) immersed in a stream of flowing gas, modern thermal flow meters can directly measure mass flow, without the need for temperature or pressure compensation. Thermal meters offer very high turndown, accu- racy and repeatability at an economical ...


    By Sierra Instruments, Inc.

  • Water Level Measurements-Part 1

    Confused about which instrumentation to use in your water level monitoring system? In-Situ offers two categories of pressure sensors for water level measurements: absolute or non-vented sensors, and gauged or vented sensors. They look the same and both measure pressure and water level, but they have drastically different applications, outputs and accuracy. The absolute (or non-vented) water level ...


    By In-Situ, Inc.

  • Reducing Costs of Steam Flow Measurement

    Traditionally, steam flow has been measured with a differential pressure device. This is typically an orifice plate. However, such devices are inherently volumetric flow measurements. As we have discussed in previous blog posts, changes in pressure and temperature ...


    By Sierra Instruments, Inc.

  • Industrial thermal mass flow meters Pt.1 -Pt.2 - measurement & control

    An industrial thermal mass flowmeter measures either the mass velocity at a point in a flowing gas or the total mass flow rate through a channel or pipe. Figure 1 shows a typical thermal mass flow sensing element. It consists of two sensors: a mass flow sensor and a temperature sensor, which automatically corrects for changes in gas temperature. Both sensors are reference- grade platinum ...


    By Sierra Instruments, Inc.

  • Oxygen Monitors for the New Millennium

    Oxygen monitors have become a required piece of safety equipment for many industrial and laboratory environments, where the release of certain toxics can create an area unsafe for living beings (human or animal).  When making a purchasing decision on any oxygen detection monitor, one need look no further than the sensor cell found at the heart of the monitor.  While each oxygen ...

  • Wastewater Level Measurement Techniques

    Level monitoring and control is a fundamental requirement in any wastewater treatment process. You will find level instrumentation installed at even the simplest treatment plants for pump control, chemical storage tanks and process level controls or alarms. Operators have only limited or emergency control over treatment plant influent, so level controls and instrumentation play an important role ...


    By Greyline Instruments Inc.

  • Arica Pago de Gomez, Chile - Case Study

    Fast Facts Contaminant: Arsenic Flow Rate: 2.5 MGD In November 2011, AdEdge Water Technologies was contacted byXylem Inc to design, supply and start up an arsenic treatment system for Aguas del Altiplano in Pago de Gomez, Arica-Chile. The Pago de Gomez Water Treatment Plant added an arsenic treatment unit to its existing ...

  • City of Roswell, Georgia - Case Study

    In late 2011, the United States Army Corps of Engineers (USACE) approved plans to install a new well and build a new water treatment facility for the City of Roswell, Georgia. Barlovento LLC was selected during a competitive bidding process to provide an iron and manganese removal system for the new water supply. AdEdge Water Technologies, LLC was contracted to design, manufacture, and commission ...

  • City of Green, Kansas - Case Study

    In September 2012, AdEdge Water Technologies, LLC participated and was awarded a Contract managed by BG Consultants for the equipment pre-selection of a nitrate removal treatment system for the City of Green, Kansas. The scope of the contract included the design, manufacture, and startup of the treatment system. The City of Green is a small community of approximately 125 residents located in ...

  • City of Aurora, Oregon - Case Study

    In late 2009, Water Works Engineers contacted AdEdge to design and implement an arsenic, iron, and manganese removal system to serve the City of Aurora, Oregon. The existing water supply consisted of three wells feeding into a centralized distribution system with a maximum combined capacity of 500 gpm. The site had an arsenic level of 12 ppb, above the EPA's MCL of 10 ppb. The City of Aurora also ...

  • Gore Hill, Montana - Case Study

    In November 2009, AdEdge Water Technologies, LLC was contacted by Great West Engineering to provide an arsenic and iron removal system for the Gore Hill County Water Treatment Plant Wells #1 and #2 in Great Falls, Montana. The existing water system consisted of multiple wells feeding into a centralized distribution system with a maximum capacity of 150 gpm. The raw water for Plant #1 has an ...

  • Project profile - Webb Consolidated Independent School Bruni, Texas arsenic treatment system

    Background Webb Consolidated Independent School District (Webb CISD) located in Bruni, Texas applied to the U.S. Environmental Protection Agency (USEPA) to participate in the arsenic treatment demonstration program for Round 2 and was selected. The school has a water-supply well which pumps water to a 12,000 gallon storage tank. Waterquality analyses revealed that arsenic concentrations ...

  • Project profile - troyer water system – Middlefield, Ohio arsenic, iron & manganese removal

    Background In early 2008, AdEdge was selected by EcoWater Servisoft in Burton, Ohio to design, build, and startup an integrated treatment system to remove arsenic, iron, and manganese levels at the Troyer Water System in Middlefield to below the primary and secondary MCLs of 0.010 mg/L, 0.3 mg/L and 0.05 mg/L respectively. AdEdge first piloted a treatment system in spring of ...

  • Project profile - century packaging - Las Piedras, Puerto Rico arsenic treatment system

    Background In February of 2010 AdEdge was engaged by Pharmaceutical Services & Installations (PSI) to provide a treatment option for the Century Packaging Corporation in Las Piedras, Puerto Rico. The packaging facility has a water-supply well which pumps water to a 30,000 gallon storage tank and has a daily utilization of 60,000 gallons per day. Water-quality analyses revealed that ...

  • Project profile - City of Wellman, Texas arsenic treatment system

    Background The City of Wellman, Texas (Wellman) applied to the U.S. Environmental Protection Agency (USEPA) to participate in the arsenic treatment demonstration program for Round 2 and was selected. Wellman has five water-supply wells which pump water to a 110,000 gallon storage tank. Water-quality analyses revealed that arsenic concentrations exceeded the new maximum contaminant level ...

  • Desert Sands MDWCA #4, New Mexico - Case Study

    In August 2008, AdEdge Water Technologies was contacted by the engineering firm Bohannan Huston to design, supply and start up an arsenic and iron removal system for Desert Sands MDWCA Well #4 in Anthony, New Mexico. The water chemistry had an arsenic level of 17 to 20 ppb and a naturally occurring iron level of 1 mg/L that will facilitate co-precipitation and removal of arsenic. AdEdge was ...

  • Lake Josephine Community, Florida - Case Study

    In January 2010, AdEdge Water Technologies, LLC was contacted by Aqua Utilities Florida to provide a hydrogen sulfide removal system for the Lake Josephine Community located in Highlands County, Florida. The existing water system consisted of two wells feeding into a centralized distribution system with a maximum capacity of 230 gpm being consumed by a population of 1,250 persons. The raw water ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you