drilling system Articles

  • Raw material cycle: from chip to briquette to product - Case Study

    Thanks to their briquetting system from RUF Frischhut can redeploy production scrap and melt it again Ludwig Frischhut GmbH and Co. KG have closed the circle on their raw material cycle by utilising a briquetting press from RUF: cast chips produced during the machining of parts for water supply and sewage disposal are pressed to solid briquettes and then melted in the in-house foundry and ...

  • Drilling Mud Circulation System

    As more utility contractors are moving up to larger rigs, they are also moving toward the use of solids removal ( solids control ) systems. These solids control systems are not stand-alone units. They are part of the drilling mud system along with the ...


  • Horizontal drilling

    Summary: Horizontal drilling is used to install pipes for cables etc under obstacles such as buildings, rivers, roads etc. The drilling operation can be considerably delayed if the depth of drilling is chosen to coincide with underground ...


    By Advanced Geosciences, Inc.

  • Drilling Mud and Mud Circulation System

    As more utility contractors are moving up to larger rigs, they are also moving toward the use of solids removal ( solid control ) systems. These solid control systems are not stand-alone units. They are part of the drilling fluids system along with the drilling fluid and the fluid pump. ...


  • Geo Drilling International: Hands-On

    Boart Longyear has launched a core-orientation system made for drillers, by drillers Although critical for mapping exploration and minesite development, core orientation is part of the drilling process that has experienced only incremental product improvements through small changes to the process and equipment. Boart Longyear has now introduced TruCore, a first-inindustry integrated ...


    By Boart Longyear Inc.

  • Drilling for oil is not the answer

    The United States consumes nearly 21 million barrels of petroleum per day (7.5 billion barrels per year), one fourth the world total. Of the crude oil consumed in the U.S., 66 percent is imported. The U.S. is on pace to spend over $500 billion on petroleum imports in 2008. U.S. oil production currently occurs onshore in the lower 48 states (2.9 million barrels per day (mbd)), offshore (1.4 mbd, ...


    By Earth Policy Institute

  • Optimizing drilling efficiencies with a solids control system

    The correct solids control system can improve drilling rig efficiency, reduce costs and minimize the environmental footprint of your operation Although the use of drilling fluids within the HDD / trenchless industry is still relatively new, recent trends suggest that this standard is shifting as solids control is one of the most important phases in the drilling process. This shift is due ...

  • Solids Control for Drilling Mud Process System

    Nowadays, more and more drilling contractors recognize solids control’s importance to oil and gas drilling, HDD, CSM/CBM exploration, etc. How does solid control affect well drilling? Please find the following details. Cost Comparison of Two Oil Well Drilling Let’s find the difference of two kinds of oil well drilling with and without solids control system. Final effect or result is ...


  • How to Deal with Drilling Waste

    At present, environmental protection is a basic state policy in China, and it has been a strategic mission and goal for our country to maintain a sustainable development of society, economy and environment. Along with the continuous improvement of environmental laws and the increasing environmental awareness among people, the departments concerned have successively enacted various environmental ...


  • Drilling oil recovery from drill cuttings case study

    By econ industries VacuDry indirect heated thermal desorption Drill cuttings are an increasing waste stream worldwide, econ industries addressed the challenge by developing a process that cleans the waste and at the same time recovers valuable drilling oil. The VacuDry plant started the successful processing of drill cuttings in autumn 2013. Our client, a medium-sized recycling company, was new ...


    By econ industries GmbH

  • Centrifuge Technology in Drilling Fluid Recycling

    Drilling fluid additives and the water that contains them are an essential part and expense of successfully completing a horizontal directional drilling (HDD) installation, and the longer the bore and larger the product being installed, the more drilling fluids cost. Therefore, it makes economic sense to recycle drilling fluids by removing cuttings and recirculating the cleaned ...


    By Elgin Separation Solutions

  • Case Study: Nigerian Drilling Platforms

    Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the seven oil-drilling platforms off of the coast of Nigeria. The first platform had samples from the industrial laundry, kitchen, emulsified, cutting oily-water and drilling mud. The samples were treated individually and then combines so as to simplify the platform ...


    By Integrated Engineers Inc.

  • Industry leading drilling fluid dewatering

    The drilling industry is regulated by a myriad of environmental regulations that protect our air, water, and land resources. As these regulations continue to evolve, so too must the technologies utilized by the drilling industry. Though lowering compliance costs is always a worthy initiative, incorporating technology that also enhances the drilling process by improving down-hole conditions and ...


    By Elgin Separation Solutions

  • Oil Drilling Operation Wasteawater Treatment

    Wastewater Treatment Success Stories Oil Industry Operation Wastewater Treatment Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the ...


    By Integrated Engineers Inc.

  • SAS drilling mud cleaning products

    Effective & fast mud cleaning for the oilfield. SAS microemulsion drilling mud cleaning products speed up the cleaning and removal of drilling mud waste. The cleaning of drilling mud residues from mud pits, offshore supply vessels and mud trucks is traditionally a time consuming task. Using high pressure water or standard cleaning detergents usually results in large volumes of mud slop ...

  • Nigerian drilling platforms wastewater treatment

    Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the seven oil-drilling platforms off of the coast of Nigeria. The first platform had samples from the industrial laundry, kitchen, emulsified wastewater, cutting oily-water and drilling mud. The samples were treated individually and then combined so as to simplify the ...


    By Integrated Engineers Inc.

  • Portable Remotely Operated Drill (PROD): Hydrocarbon Sensing System

    Proven Technology Benthic’s prototype Hydrocarbon Sensing System (HSS) analyses drill returns for the presence of hydrocarbons as they pass through PROD before being vented on the seafloor. The System, in its present form, includes two hydrocarbon sensors in line with the drill returns path. Drill returns, composed of seawater drawn from above PROD and pumped down the drill ...


    By Franatech GmbH

  • Horizontal Directional Drilling - A Green and Sustainable Remediation Remedy

    Interest in using sustainable practices and technologies for environmental cleanup has increased notably within the past few years. The US EPA and many states have published recommended practices to reduce the environmental footprint of cleanup operations, and many consultants and contractors are attempting to “go green” in contaminated site remediation. It makes sense to conserve ...

  • Mono nov at the cutting edge of drill waste management

    Equipment from Mono is being used in a joint venture with Baroid Drilling Fluids at a state of the art facility in Kazakhstan. Baroid, part of the Halliburton Company, provides drilling fluids and services to energy companiesworldwide, and is a global leader in Total Fluids Management services. The system is a fully contained closed system and uses a Mono pump for handling oil-based mud ...


    By NOV Mono - Mono Pumps Ltd

  • Mono nov at the cutting edge of drill waste management

    Equipment from Mono is being used in a joint venture with Baroid Drilling Fluids at a state of the art facility in Kazakhstan. Baroid, part of the Halliburton Company, provides drilling fluids and services to energy companiesworldwide, and is a global leader in Total Fluids Management services. The system is a fully contained closed system and uses a Mono pump for handling oil-based mud ...


    By NOV Mono - Mono Pumps Ltd

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you