engine particle filter Articles

  • NIOSH Announces Sampling Strategy to Help Identify Potential Nanomaterial Exposure in an Occupational Setting

    On November 1, 2016, the National Institute for Occupational Safety and Health (NIOSH) published a blog item entitled “Never fear!  NEAT 2.0 is here! — How to perform nanomaterial exposure assessment in the workplace.”  NIOSH notes that in 2009, it developed and was the first to recommend using the nanoparticle ...


    By Bergeson & Campbell, P.C.

  • Seven Ways Your Facility Isn’t Meeting Effluent Regulations and How to Solve Them

    Whether you own, operate, or help manage a municipal or industrial facility that deals with wastewater, it’s important to understand how wastewater treatment can play a significant role in the overall health of your business, especially when it comes to meeting effluent regulations. This is an important part of the wastewater treatment process to consider, as ignoring it could earn your ...


    By SAMCO Technologies, Inc.

  • An end to the problem of particle emissions

    Austrian biomass heating systems guarantee an 80% cut in emissions. Recent studies have shown that these modern domestic boilers offer a significant reduction in particles, emitting fewer contaminating agents than previous generation boilers and wood stoves – with more than 100mg / ml of particles. The future will be based on new biomass combustion technology which cuts dust emissions from ...

  • Office Printers Emit Ultra fine particle pollution

    We’ve heard quite a bit about particulate matter PM10s and PM2.5s as components of air pollution that we are exposed to on a daily basis. Recent research papers are highlighting the dangers of ultra fine particles (UFPs), which have a diameter of less than 0.1 micrometres (or 100 nanometres). By contrast, the diameters of particulate pollution from PM10s and ...


    By Commercial Air Filtration

  • Evaluation of Tire Derived Rubber Particles for Biofiltration Media

    ABSTRACTCurrently, on average, one tire is discarded in the U.S. for every man woman and child every year. While the reuse market for used tires has increased over the years to approximately 75%, there are still an estimated 2-3 billion used tires stockpiled in the U.S. Finding economical and sustainable end uses for this tire material is an ongoing challenge to environmental engineers and ...

  • Particle Measurement Programme (PMP) Light-duty Inter-laboratory Correlation Exercise (ILCE_LD) Final Report

    The Light Duty Inter-Laboratory Correlation Exercise has conducted testing at 9 test laboratories in the EU, Korea and Japan in order to demonstrate the practicality, robustness, repeatability and reproducibility of the particle emissions measurement techniques proposed by the Particle Measurement Programme (PMP). The exercise involved testing 16 light duty vehicles including 6 diesels equipped ...


  • Tyre aggregate applications in geotechnical and geoenvironmental engineering

    A Tyre Aggregate (TA) is made from scrap/waste rubber tyres. Four types of tyre aggregates are classified, namely the coarse-grained, fine-grained, random and composite tyre aggregates. Applications of these tyre aggregates are varied, but they are often used as geomaterial fills and highway-pavement components. More recently, TA has found application in geoenvironmental engineering. This paper ...


    By Inderscience Publishers

  • Predicting Diesel Particulate Filter Performance

    The diesel particulate filter (DPF) has been used for many years in the control of diesel particulate matter (DPM)emissions. This technology is characterised by extremely high efficiency and high sensitivity to the application conditions. Research and testing performed by Diesel Controls Ltd. over the past two years has resulted in improved methods for predicting the application based performance ...


    By DCL International Inc.

  • To prevent blinding in dust collection systems, consider filter type, filter size and selection of the filter media used

    All dust collection systems, regardless of size, share a common problem—dust blinding. Simply stated, blinding is defined as when dust particles plug the holes in a filter and stop the flow of air through the filter, resulting in the dust collector performing poorly. All types of collectors, whether stand-alone units, cyclones or full-scale baghouses, are subject to blinding. To better ...


    By American Fabric Filter Co

  • Combinations of Measures for Reduction of NOx & Nanoparticles of a Diesel Engine

    Reduction of NOx- and particle emissions of Diesel engines is worldwide an important challenge for the engineers. Some unregulated components, like NO2, NH3 and naoparticles NP came in the focus of attention in the last years.Application of EGR and / or SCR can lower NOx, using RME (Bxx) can increase NOx. What happens with NP, parameter which enters in some further steps of exhaust gas ...


    By Vestlandsforsking

  • How to Choose the Right Commercial Air Filter

    When it comes to selecting a commercial air filter, or air filtration system, there are many variables that have to be considered. In general, the choice of which air filter can be made a bit easier by first defining the overall goal that you are trying to achieve which is usually one of two options. Is the purpose of the filter to protect the air circulation equipment, or is it to provide a ...


    By Camfil Ltd

  • Beta ratios explained and applied to liquid filter selection

    Liquid Filter Beta Ratios: Absolute rated liquid filter selection is tied to the media micron rating, materials of construction, construction design, and particulate removal efficiency filter factor known as its Beta Ratio (Figures 1, and 2). Consider that Engineering and Purchasing usually see absolute rated liquid filter efficiencies from vendor data sheets and quotes listed at 99%, ...

  • How well does my filter work?

    Contamination control is the key to a cost-effective maintenance operation for hydraulic or engine systems. You depend on your filters, whether hydraulic, lube or fuel, to keep your fluids clean, to keep maintenance costs down, and to ensure reliable operation. At some point, you probably will ask yourself whether or not your filters are really working and doing what they were designed to do. ...

  • Removing Solids with Automatic Self-Cleaning Filters

    Introduction The “art” of filtration utilizes many methods for separating solid particles from fluids. There is often no right or wrong method. Water quality and customer requirements usually determine the “best” method for each unique situation. Ridged screens, pleated cartridges, string wound cartridges, melt blown cartridges, woven fabrics, non woven fabrics, sintered metals, granular ...

  • American Upstart Filter Brand Competing with the Majors

    Flexotherm® has expanded its product line in the highly competitive filtration market.  The company now offers 2,900 different filter elements including coalescers, particulate, adsorbers, general purpose and high temperature filters. ...


    By Neptech Inc.

  • A Layman`s Guide to Inorganic and Organic Contaminant Removal by Standard Filtration Methods

    Plant operators, maintenance engineers and mechanics, specifying engineers, installation technicians, and others involved in inorganic and organic contaminant removal are oftentimes called upon to choose and apply filtration solutions. To best make these decisions, it is helpful to review information and updated insight on basic filtration technologies, along with their advantages and ...


    By Shelco Filters

  • Case study - Safety, Protection against corrosion and cabinet pressurisation in refineries

    The environment in a refinery is highly corrosive. This makes it necessary to deploy control systems not only to protect staff but also to protect the equipment controlling the processes, in order to ensure their reliability. Bioconservacion has equipment that is specially designed for the safety of staff, and for protecting against corrosion in control rooms and cabinet pressurisation equipment. ...


    By Bioconservacion SA

  • Mine backfill

    Mine backfill is defined as the material used to fill the cavities (i.e., stopes) created by underground mining. Backfilling can be a means to dispose of sludge and/ or tailings which may contain hazardous materials and to reduce surface environmental impacts by storing tailings underground. Alternately, backfilling with nonhazardous materials can allow for mining productivity improvements. To ...


    By WesTech Engineering, Inc.

  • Methods of Water Purification

    This article is excerpted from 'Pure Water Handbook' published by Osmonics®, Inc. of Minnetonka, Minnesota USA and is printed with permission of Osmonics, Inc. Water treatment can be defined as any procedure or method used to alter the chemical composition or natural 'behavior' of a water supply. Water supplies are classified as either surface water or groundwater. The majority of public or ...

  • Techniques for Soot in Oil Analysis

    Since no engine is 100% efficient, products other than carbon dioxide and water will be formed during combustion. One such product produced from incomplete combustion is soot. Soot is a mass of mainly carbon particles that are typically spherical in shape. As soot levels rise, the soot particles begin to clump together and ...


    By Spectro Scientific

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you