flammable gas alarm Articles

  • Monitoring flammable gas in boiler houses

    The most common fuels in use for space and water heating are Oil, Natural Gas and Liquid Petroleum Gas (LPG). By far the most popular, clean and cost effective solutions are utilising Natural Gas or LPG. The traditional safety measure derived from the time of oil fired boiler houses is the use of a fusible link placed above the each boiler. The fusible link is intended to melt if it becomes ...

  • Compressed Gas Safety Guide

    Use and storage of any compressed gas under high pressure can be extremely dangerous if proper gas handling procedures are not observed. Moreover, chemical characteristics of specialty gases themselves can pose serious health hazards if containment is not tightly controlled. Paying close attention to a compressed gas product’s technical and safety information is invaluable for maintaining a safe, ...

  • Detect Hydrogen Gas and Flames

    Under day-to-day conditions, people cannot see, smell, or taste the presence of hydrogen gas. Hydrogen, however, is very flammable and requires only a small amount of energy to ignite. In fact, if leaking from a pipe at a high enough pressure, hydrogen gas can self ignite without the aid of an external energy source. Working together, ...

  • Gas detector communication technology for offshore oil and gas platforms

    In few applications is safety as important as on offshore oil and gas platforms. Explosive hazards from hydrocarbon gases and vapours are an ever-present risk, whilst toxic hydrogen sulphide gas and depleted oxygen environments can pose significant risks to personnel. Gas detectors are therefore essential to provide dependable early warning of gas hazards. Gas detectors are permanently installed ...

  • Upgrading from Pellistor Gas Sensors to Infrared Technology

    In this article Andy Avenell, Crowcon’s Fixed Systems Product Manager, considers the shift towards infrared (IR) gas sensor technology in the oil and gas industry. Abstract Flammable gases and vapours can present considerable dangers in many industrial applications, none more so than the processes involved in extracting, transporting and processing oil and gas. Fast and reliable ...

  • Benefits of HART Communication-Enabled Gas and Flame Detectors

    Catastrophic results can occur when a fire or a flammable/toxic gas release goes undetected in any petrochemical facility. For early warning and prompt hazard mitigation, flame detectors and gas detectors are essential tools. Clear, usable, diagnostic information from these detection instruments is extremely valuable in ensuring the devices are properly maintained, tested, and poised to protect ...

  • Selecting and Placing Gas Detectors for Maximum Application Protection

    Many industrial processes involve dangerous gases and vapors: flammable, toxic, or both. With the different sensing technologies available, and the wide range of industrial applications that exist, selecting the best sensor and locating them properly for the job at hand can be a challenge. To ensure a high level of safety, know the latest sensing technologies, which technology is best for the ...

  • Detecting Hydrogen Gas and Fires: Seeing the Unseen

    Hydrogen usage is growing. The general public sees and reads about hydrogen as an alternative fuel for cars. However, the big use for hydrogen is found in hydrocarbon processing and other important manufacturing processes. Hydrogen is the first element on the periodic table and is an essential element in the manufacturing of many of our everyday products. We must have respect for its explosive ...

  • Follow toxic gas standards for a smoother project

    Toxic gases, such as Hydrogen Sulfide and Sulfur Dioxide, can injure and kill quickly. Therefore, mitigation of these hazards must be fast and sure. The United States Occupational Safety and Health Administration (OSHA) and other authorities take detection of these gases very seriously. The American National Standards Institute/ American Petroleum Institute (ANSI/API) and ISA industry standards ...

  • Safety Systems Depend on Reliable Field Sensors (Emphasis on Fire and Gas Detectors)

    Abstract Because not all hazards are the same, identifying and quantifying the hazard is the starting point in choosing sensing technology. Not all detectors are the same, and they should be selected according to their ability to detect the hazard. This paper gives a broad summary of technologies that provide users reliable responses to hazardous conditions, that minimise false ...

  • Fire and Gas Protection Systems as Part of Safety Instrumented Systems and Risk Management

    Garth Watkins, Director Europe, Middle East, Africa, Detector Electronics Corporation, Presented at HazardEx International Conference 2008 Process-systems operators today face increasing demands for lower costs and higher safety standards in an increasingly regulated environment. In addition, companies desire to provide a working environment that is as safe as possible. As a result, plant owners ...

  • PureAire Combines Oxygen and CO2 Sensors to provide a Dual Gas Monitor to the Marketplace

    As a recognized leader in O2 safety monitoring, PureAire recently explored the need for an O2 monitor where carbon dioxide is used. There are four key cryogenic gases; nitrogen, helium, argon, and carbon dioxide (CO2), which can create an oxygen deficient atmosphere. Material Safety Data Sheets (MSDS) covering cryogenic gases cite that a cryogenic leak can create an unsafe ...

  • Not All Hazards are the Same: Design considerations for matching flame and gas hazards to detector technologies

    Not all flame and gas hazards in facilities are the same, therefore the detection technology chosen should be specific to the type of hazard to be detected. How do users select technologies to see certain fires or detect certain gases? The intent of this paper is to give a broad introduction to the selection and use of flame and gas detector technologies. We will answer questions such as these: ...

  • Paint booths, or areas using combustible gases: why a requirement for combustible gas monitor might be necessary

    Paint booths save time and ensure a smooth and professional application of paint in a range of industries, including automotive, aerospace, home decor, furniture, and more. Combustible gases and fluids in the paint booth environment can pose a health hazard if something goes wrong. Explore the hidden dangers of paint booth fluids and gases, and learn how a ...

  • Don’t Risk Your Life Going Up in Smoke

    What you need to know about smoke alarms Fire is an inescapable risk in both the home and workplace, with electrical products, heating and gas all presenting the possibility of an accidental blaze under the wrong circumstances. Preventing fires altogether with effective precautions is always preferable, but regardless at least one smoke alarm/detector – or mains powered ...


    By SHEilds Ltd

  • Preventing a Future Crisis - Addressing Water Contamination & Treatment in Flint, Michigan

    Poisoning conjures up images of evil men sneaking away as unsuspecting victims clutch their throats and fall over dead at the dinner table. The reality of poisoning is much more sinister, and its potential sits on a larger scale than most municipalities and states are willing to acknowledge. Lead, bacteria, copper, and other contaminants are drifting in the pipes of Flint, Michigan, and resting ...

  • If you can`t stand the CO2, get out of the kitchen - part 1

    There are two potentially dangerous types of gas in a commercial kitchen: 1) the flammable ones used for cooking (e.g. methane/natural gas; propane/liquefied petroleum gas); and 2) the noxious, gaseous products of combustion such as carbon monoxide, carbon dioxide and hydrocarbons. It would be good to know how to avoid them. But a search for advice on kitchen ventilation threatens to drown the ...


    By Analox Sensor Technology

  • Carbon Monoxide (CO) and Carbon Dioxide (CO2) Safety

    Know the Gases, Know the Dangers and Protect Yourself Do you know the differences between carbon monoxide (CO) and carbon dioxide (CO2)? If you don’t then there are no guarantees your safety measures will be adequate. These two different gases are often mixed up with people becoming confused over which they need to protect against, when and how. ...


    By SHEilds Ltd

  • What is added value?

    We’ve probably all heard people referring to their “value added” service or product. Some of us have probably said it to our customers but what exactly does it mean? The UK supermarket Kwik Save launched a budget brand in the 1990s called “No Frills”. I believe they were the first to do this on a large scale and it was a great success. It was founded on the idea of ...


    By Analox Sensor Technology

  • Read about Confined Space in Construction and Atmospheric Testing Right Here!

    In 1993, 29 CFR 1910.146 went into effect as the first federal legislation governing entry into permit-required confined spaces in general industry. Because some industries, such as the construction industry, were covered by specific Occupational Safety and Health Administration (OSHA) safety regulations, they were exempt from the confined space entry requirements of the general industry rule. ...


    By Argus-Hazco

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you