gas hazard Articles

  • CO2 Gas Hazards in the Brewing Industry

    The hazards associated with CO2 in the brewing industry are well known, yet people still die needlessly every year in tragic and completely avoidable accidents in breweries. Just last year in Germany, which has a good safety record, two workers died in separate incidents at the same brewery. In the first incident, the owner was found dead with his head and torso in a beer mixing tank. It is ...

  • Flammable Hazards

    Flammable Hazards The difference between a gas and a vapor is that vapors arise from liquids, whereas gases are normally in a gaseous state. Flammable vapors present additional sampling concerns (for example, we must prevent vapors from returning to the liquid state during sampling). The 3 Elements of Fire Three elements must be present for a flammable ...

  • Monitoring Multiple Gas Hazards in Ice Arenas

    The equipment used in an arena such as an ice re-surfacer, ice edger, floor sweepers, lift trucks and other special equipment are more often powered by fuel than electricity. The exhaust produced by the gas, propane or diesel fuel powered machines emits, into the air, carbon monoxide (CO), nitrogen dioxide (NO2) and particulates. Ammonia (NH3) is commonly used in the ice chiller mechanical room ...

  • Indoor Air Quality and Hazardous Gas Detection

    Indoor air contaminants come in a variety of forms and originate from multiple sources. Interactions between building materials and furnishings, activities and equipment inside the building, internal temperature and relative humidity, filtration and ventilation system operations, climate and building occupants all contribute to the indoor air quality (IAQ) in commercial, industrial, residential ...

  • Not All Hazards are the Same: Design considerations for matching flame and gas hazards to detector technologies

    Not all flame and gas hazards in facilities are the same, therefore the detection technology chosen should be specific to the type of hazard to be detected. How do users select technologies to see certain fires or detect certain gases? The intent of this paper is to give a broad introduction to the selection and use of flame and gas detector technologies. We will answer questions such as these: ...

  • A Two Channel Gas Detector for Monitoring Hazardous Gases in the Workplace

    The potential for exposure to hazardous gases is a concern in many workplace environments. To ensure the safety of the workers, equipment, and the facility, areas presenting a gas hazard should be monitored by gas detectors. Commercial buildings that share a warehouse with manufacturing and/or service work in the back and offices in the front are a prime place for harmful gases and vapours ...

  • Safety Considerations at Anaerobic Digestion Plants

    Anaerobic digestion is a collection of processes which naturally breakdown organic matter to eventually produce biogas - a methane rich gas which is burned to produce both heat and electricity. The methane can also be used as vehicle fuel or injected into the gas grid. The industry is growing fast and is forecast to continue to do so with many farmers adding bio-gas plants alongside their ...

  • A Hazardous Road to Success

    Chromatotec have established themselves in the Forefront of Sulphur Analysis in Hazardous Areas. Their latest Enhancement of their MEDOR range has Augmented their Rapid Rise in this Expanding Market. Most natural gas production and exploitation sites are considered to be hazardous area. This is certainly the case when it comes to Liquefied Petroleum Gases (LPG) sites. It is vital ...


    By Chromatotec Group

  • Health Hazards of Welding

    At present, it is estimated that more than one million workers are employed as welders worldwide (Sundin, 1998), with more than three million performing welding intermittently as part of their work duties (Sferlazza and Beckett, 1991). Manual metal arc welding (MMAW) and flux core arc welding (FCAW) are two commonly used procedures in the construction industry and in numerous other industrial ...


    By Valahia University

  • Classifying Hazardous Areas

    The IEC is composed of approximately 40 countries including the United States. The purpose of the IEC is to establish standards for a wide variety of electrical products with the intent of encouraging international trade. The IEC has assigned a technical committee, TC 31, to develop recommendations covering equipment, testing procedures and classification standards for areas where the potential ...

  • Management of Hazardous Wastes

    ' Management of hazardous waste is a growing concern in many countries. The long-term impacts and costs of improper disposal can be very high and the emphasis must be on prevention. A comprehensive management system should include (i) policies, institutions and effective regulations and (ii) adequate and acceptable disposal facilities (either public or private). This note outlines the key ...


    By The World Bank

  • The Influence of PVC on the Quantity and Hazardousness of Flue Gas Cleaning Residues from Incineration

    The study estimates the influence of PVC on the quantity and hazardousness of flue gas residues from incineration. The analysis has been carried out on both theoretical and practical terms. A distinction between dry, semi-dry and wet gas treatment systems has been made. The influence of PVC has been assessed on the combustion steps and therefore on the distribution of chlorine and other ...

  • The Hazards of Being in a Beauty Salon

    There are many health risks associated with the beauty industry due to the chemicals found in the products. We are all affected by these chemicals every time we go to the beauty salon. Many of the products found in these salons are classified as hazardous and extreme caution should be taken into consideration when using these products. They’re made for professional use only; therefore, ...

  • Hot Gas Decontamination

    Introduction: The process involves raising the temperature of the contaminated equipment or material to 260 °C (500 °F) for a specified period of time. The gas effluent from the material is treated in an afterburner system to destroy all volatilized contaminants. The method eliminates a waste that currently is stockpiled and requires disposal as a hazardous material. This method will permit ...

  • Dispense Gas Safety

    What Is Dispense Gas? Inert gases such as carbon dioxide and nitrogen are used regularly within the hospitality industry. These gases, known collectively as ‘dispense gas’, are used to carbonate drinks so ...


    By Analox Sensor Technology

  • Hazardous chemicals and proper storage solutions

    Many acceptable categorical storage schemes have been proposed and used by laboratories in academic, industrial, government and medical institutions. The common features uniting all these plans is the separation of incompatible materials. The differences in these various storage schemes arises in the number of groups that should be established for segregation purposes. The ten most commonly cited ...


    By US Chemical Storage

  • Corrective action at a hazardous waste unit

    Troy Risk performed a RCRA Corrective Action at a closed hazardous waste landfill for a multinational landfill company. The work involved inspection and cleaning of two 85-foot leachate risers. A leachate riser is a stack of 4-foot diameter concrete pipe sections, which provide a passage to the bottom of the hazardous waste landfill. The riser provides access to pumps and electronic leachate ...


    By Troy Risk, Inc.

  • Gas Phase Filtration Industrial Gas Purification

    Purification of Industrial Gases ...


    By Bioconservacion SA

  • Fixed multi-parameter gas detection system can ensure industrial facilities are safe from hazardous or toxic gases

    Industrial workplaces are likely to come across one or more hazardous or toxic gases. Combustible gases such as methane are highly dangerous because they can cause large and fatal explosions when ignited. Other problem areas when working in industry are carbon monoxide (which poisons the cardiovascular system), oxygen deficiency, and elevated levels of other gases and pollutants, depending and ...


    By PPM Technology

  • NEC Classifications and Divisions for Hazardous Locations

    Electrical equipment in hazardous (classified) locations present a serious threat for workers due to the existence of explosive dust and vapors. Examples of such facilities range from grain mills and gasoline stations to aircraft hangars and chemical manufacturing plants. To prevent devastating explosions that may occur from the ignition of combustible particles in the atmosphere, the National ...


    By Larson Electronics LLC

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you