inline mixer Articles

  • Inline static mixer simplifies process & reduces cost for yogurt manufacturer

    The increasing popularity of yogurt in recent years-requiring greater production capacity and efficiency-has brought about a need to “re-think” just how best to feed raw materials into mixing and blending systems, and into filling machines. Initially, in most European and U.S. plants, the mixing of milk, yogurt culture, and additives was essentially a hand-batching process. This ...


    By Komax Systems, Inc.

  • Ketchup manufacturer replaces stirred tanks with static mixer

    Over twenty years ago Hunt Wesson (ConAgra) installed the Komax static mixers in all of their plants in North America. The first Komax installation was in Hunt Wesson"s Southern California plant. One 4 inch diameter Komax Ketchup mixing system out produced fifteen 5000 lb stirred tanks that were used for their daily production. Two months after installation Komax added a short flanged tube ...


    By Komax Systems, Inc.

  • Komax teflon lined mixer simplifies acid injection for power plant

    A major source of waste water in many power plants is the waste stream that results from ion exchange used for demineralizing the boiler feed water. The alkaline regeneration waste stream produced by the ion exchange process requires the addition of an acid to this stream before discharge from the plant. Regulatory authorities typically require the effluent to have a near neutral pH before ...


    By Komax Systems, Inc.

  • Kenics static mixer increased production rates and productivity yield when used for adding pigment color

    Adding a pigment color to a dynamic mixer that is also used for non-colored products creates color contamination of the wetted parts and results in increased labor as well as production time and yield losses that directly affect the bottom line. The Kenics KM Series Static Mixer, manufactured and marketed by Chemineer, Inc., provides an alternative solution to adding pigment color that eliminates ...


    By National Oilwell Varco

  • In-line mixer handles tough blending job - tomato paste and water at 100 gpm

    Citrus World, Florida’s third largest fruit co-op, recently expanded its product line to include tomato juices. In doing so, the Lake Wales based processor ran across a difficult blending problem. Daniel Cronin, engineer on the project, says the co-op tried various vessels and mechanical mixing devices, in attempts to blend viscous tomato paste and water. None proved adequate, including ...


    By Komax Systems, Inc.

  • Start up of Indonesian Cinnamon Plant employs screen classifying cutter, rotary mixer

    Starting up a new process plant can be a tricky business for any company, but when it is the first plant the company has ever built and the location is halfway around the world from equipment suppliers, the project can be daunting. So it was with ForesTrade, Inc., when it set about building Indonesia's first state-of-the-art organic cinnamon-processing plant and an associated essential oils plant ...

  • Steam Heater Pulp Stock Heating Paper Mill

    After upgrading its bleach plant in 1987 to accommodate a two-stage elemental chlorine-free (ECF) bleach sequence, Cross Pointe Paper (now Flambeau River Papers LLC), Flambeau mill in Park Falls, Wis. subsequently added a totally chlorinefree (TCF) sequence in response to market demand. The TCF sequence, however, required heating, rather than cooling, of the mill's mediumconsistency stock during ...


    By Komax Systems, Inc.

  • Hielscher Ultrasonics: Ultrasonic Mixing of Cement Paste for Concrete

    The ultrasonic mixing of cement paste offers great benefits for precast molding, drycast and concrete plants. The advantages are shorter initial and final set time, lower dosage of superplasticizer, faster and more complete hydration as well as higher compressive strength. Traditional concrete mixing ...

  • Activated Sludge Treatment Plant - Eatonton, Georgia - Case Study

    Solids management at municipal wastewater treatment plants is crucial in maintaining operating efficiencies and permitted discharge levels. Drying beds and mechanical methods of dewatering bio-solids can be labor intensive and inefficient for rapid solids removal. Miratech Geotube" Dewatering Technology offers munic-ipalities a cost effective solution for rapid solids removal and long term solids ...

  • Multi-Barrier water treatment cleans up turbidity spikes

    When the city of Bloomfield, N.M., was notified by the New Mexico Environmental Department that it had 18 months to bring its drinking water treatment plant into compliance with the Interim Enhanced Surface Water Treatment Rule (IESWTR), the city needed a fast, innovative solution. Under the IESWTR, the city was challenged to meet regulatory compliance on turbidity levels. During seasonal runoff ...


    By WesTech Engineering, Inc.

  • Multi-barrier water treatment cleans up turbidity spikes

    When the City of Bloomfield, N.M., was notified by the New Mexico Environmental Department that it had 18 months to bring its drinking water treatment plant into compliance with the Interim Enhanced Surface Water Treatment Rule (IESWTR), they needed a fast, innovative solution. Under the IESWTR, the city was challenged to meet regulatory compliance on turbidity levels. During seasonal runoff ...


    By WesTech Engineering, Inc.

  • Dry mortar produced according to the state of the art

    Oradea – a town in Northwestern Romania, near the Hungarian border, is the birthplace of Adeplast, a Romanian group of companies. In 1996, Marcel Bărbuţ, became the majority shareholder of the company established in 1994 under the name Multistar Prod S.R.L. and transformed it into a Romanian-Austrian company. The link to Austria is obvious with Marcel Bărbuţ, ...

  • M-Coating – drain & sewer spraylining the economical solution to manhole shaft renovation

    M-Coating – Procedure for renovating a manhole shaft using ERGELIT Kombina KS M-Coating is a new, innovative renovation technique for both round and rectangular drainage shafts from 500mm to 1200mm. It is based on over 15 years of the Hermes company’s experience. Using this centrifuge spray technique, walls of shafts up to 10 metres deep can be coated to a realistic thickness. ...


    By HERMES Technologie Ltd.

  • Antifreeze Liquid Production: Start Your Own Business

    In some areas the cold period can last for up to eight months. Sub-zero temperatures are recorded even in October. This fact makes a small antifreeze production business quite promising. Why do we need non-freezing liquids? One important area of antifreeze liquid us is cleaning of car windscreens (windscreen cleaners). Another is cooling of the ...


    By GlobeCore GmbH

  • Painting an ever-greener picture in car production

    The announcement earlier this year that BMW Group is investing a further £100 million to increase production at its Oxford plant is good news for those buyers who have been waiting around three months to get their hands on the steering wheel of the legendary new MINI. In the paint shop, this poses a special challenge – how do you reconcile the demands of more throughput, less maintenance downtime ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you