low flowmeter Articles

  • Low-Flow (Minimal Drawdown) Ground-Water Sampling Procedures

    Untitled Document Background The Regional Superfund Ground Water Forum is a group of ground-water ...


    By Solinst Canada Ltd.

  • Cemex plant Ruedersdorf - Case Study

    CEMEX Deutschland AG is one of the biggest producers of ready-mixed-concrete, cement and minerals. In Germany CEMEX employs a staff of approximately 3,200 people and is part of the International CEMEX Group with a head count of 50,000. After the German re-unification the Company acquired the existing cement plant in Ruedersdorf. Investments to save CEMEX invested ...

  • AVFM 5.0 area-velocity flow meter monitors sewage lagoon discharge flow

    The Township of South Glengarry in Eastern Ontario discharges continuously from their 72,000 m3 sewage lagoon. But they ran into flow measurement problems when their magnetic flowmeter was unable to detect seasonal low flow rates. Operations Manager, Shawn Killoran selected a Greyline AVFM 5.0 Area-Velocity Flow Monitor because it was simple to install in a horizontal discharge pipe from the ...


    By Greyline Instruments Inc.

  • Lagoon Discharge Flow Monitoring

    Open Channel Flow Monitoring without a Flume or Weir Township operators liked the Greyline AVFM 5.0 datalogger reporting system where formatted flow reports (total, minimum, maximum and average) could be downloaded automatically to a USB memory stick without carrying a laptop to the site. The Township of South Glengarry in Eastern Ontario discharges continuously from their ...


    By Greyline Instruments Inc.

  • Vattenfall`s Cogeneration Power Plant Reuter West - Case Study

    The cogeneration power plant “Reuter West” was erected as a base load power plant in the vicinity of the existing “Reuter” plant. The two hard coal fired 300 MW units D and E were commissioned in 1987 and 1989. Today the cogeneration units supplying electricity and thermal energy are operated by Vattenfall Europe GmbH. The heart of each power plant is the boiler where the ...

  • FLOW-TRONIC S.A./N.V. - case study

    Customer: FLOW-TRONIC S.A./N.V. Sector: Water and wastewater industry Country: Belgium Technology Supplier: Microtronics Engineering GmbH Year of Cooperation: 2010 Website: www.flow-tronic.com The Customer FLOW-TRONIC is internationally recognized as the leading distributor and manufacturer of innovative and accurate liquids flow measuring ...

  • S. Dyrup & Co. selects magnetically coupled ROTAN® pumps

    S. Dyrup & Co. selects magnetically coupled ROTAN® pumps One of Europe’s leading paint manufacturers inaugurates new facility: S. Dyrup & Co. select magnetically coupled ROTAN pumps. The summer of 1998 – S. Dyrup & Co., one of Euro-pe’s leading producers of paint and lacquers, installs an advanced plant for manufacturing solvent based paint ...


    By DESMI A/S

  • S. Dyrup & Co. A leading paint manufacturer

    One of Europe’s leading paint manufacturers inaugurates new facility: S. Dyrup & Co. select magnetically coupled ROTAN pumps. The summer of 1998 – S. Dyrup & Co., one of Europe’s leading producers of paint and lacquers, installs an advanced plant for manufacturing solvent based paint and wood preservative. ...


    By DESMI A/S

  • Stormwater Solids Reduction for NPDES Permits

    Finally obtaining a National Pollution Discharge Elimination System (NPDES) Permit is often a relief but is by far not the end of the story. Meeting the requirements of that permit often proves to be quite difficult and stiff fines are freely doled out to those who fail to meet regulatory limits. For one Midwest jet propulsion manufacturing facility, the issue of total daily solids discharge ...

  • Commercial RO Package, Jordan

    INTRODUCTION In April 2013, Pure Aqua, Inc. designed and manufactured a commercial RO package to a major hotel in Jordan to remove, chlorine, TDS, and odor from well water. The package consisted of pre and post treatments including a multimedia filter and chemical dosing systems. The brackish ...


    By Pure Aqua, Inc.

  • EPA studies identify techniques for critical leak testing prior to soil-vapor sampling

    Researchers at EPA’s National Risk Management Research Laboratory (NRMRL) in Ada, OK, are developing quality assurance (QA) measures for soil-gas and sub-slab sampling methods that help differentiate contaminant vapors due to vapor intrusion from background sources. Recent research focused on measures to identify leakage of ambient air into conventional vapor probes, which can significantly ...

  • Replacement Fill Control Valves with Electronic Flow and Metering Improve Pressure, Stop Leakage and Prevent Valve Failures

    The City of Modesto, California is situated 90 miles east of San Francisco and has approximately 200,000 residents relying on 200,000 of gallons of water a day. The City needed to upgrade three water storage tanks that hold approximately 750,000 gallons each. After years of using motor operated valves to fill water storage tanks, the city recognized that there were just too many problems. ...


    By Singer Valve Inc.

  • Selecting and Placing Gas Detectors for Maximum Application Protection

    Many industrial processes involve dangerous gases and vapors: flammable, toxic, or both. With the different sensing technologies available, and the wide range of industrial applications that exist, selecting the best sensor and locating them properly for the job at hand can be a challenge. To ensure a high level of safety, know the latest sensing technologies, which technology is best for the ...

  • Gravity self-backwashing filters

    The filtration of make-up and side-stream water in closed cooling circuits, operated through cooling towers, is a fundamental step to ensure safe and continuous operations in a power plant. Water - required in large amounts for this application - should not be wasted, and the potential damages deriving from a poor treatment must be avoided at all cost. BONO ARTES has developed a technical ...


    By Artes Ingegneria SpA

  • How to Attain Precise CO2 Injection in the Carbonated Beverage Production Process

    Looking for the perfectly carbonated beverage? Is your CO2 injection process leaving your drinks flat? Industrial mass flow controllers offer the perfect solution for controlling the exact CO2 injection into beverages to create the perfect foam for the beer industry or carbonation for popular soft drinks. It is pivotal that carbonated beverage manufacturers have the ability control the exact ...


    By Sierra Instruments, Inc.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you