metal monitoring system Articles

  • Titanium Demand on Rise for Additive Manufacturing Printing: How it’s Made? Titanium Plasma Atomization.

    Plasma atomization is used in many applications, including 3D printing. First developed in 1998, this technique has risen to become the industry standard process for creating reactive metal powders suitable for 3D printing. Learn how plasma atomization works and why you need an oxygen monitor to stay safe with plasma atomization.  How Plasma Atomization Works ...

  • A quick guide to oil analysis for engine test applications

    Reliability testing is a very important component of new engine development. Engineers need to fully understand and chart the engine lifetime performance under a variety of conditions before mass production may be considered. Many important performance data parameters are collected in real time through the many different types of sensors that are connected to the engine in the test cell and oil ...


    By Spectro Scientific

  • Data Centre CRAC unit efficiency improvements

    One of the main types of project Munters look at is energy efficiency improvements within the thermal management side. One of the easiest changes that can be made is swapping out the old AC powered motors for EC powered impellors. the reductions in energy is considerable, with some older belt drive unit changes measuring a saving of over 60% this is due to the design of the new impellors and the ...


    By Munters

  • Gas Detection and Monitoring Systems

    In greenhouse applications, the accurate measurement of a number of environmental parameters such as carbon dioxide concentration, temperature, light intensity, water, humidity, pH and nutrient levels using sophisticated sensors is used to create a controlled environment for optimising plant growth rates while minimising energy usage. Carbon dioxide concentration is also one of the best ...


    By Edinburgh Instruments Ltd

  • X-Ray Fluorescence-Based Multi-Metal Continuous Emission Monitor

    ABSTRACT: Army demilitarization incinerators will need to comply with the Hazardous Waste Combustor National Emission Standard for Hazardous Air Pollutants that will regulate metals and metal compounds listed under the Clean Air Act Amendments. A large problem for these incinerator operations is limited knowledge of the type and quantity of emitted metals, so that compliance may be determined ...

  • Collini metal processing plant

    Introduction The submerged membrane bioreactor plant at Collini galvanic industries in the West of Austria is a fine example of process optimization in a complex industrial environment. The plant is owned and operated by Collini and is now in its 3rd year treating wastewater from a metal processing facility. It is sited in an industrial estate and discharges into a small waterway in an ...


    By Kubota Membrane

  • Sustainable metal working fluid systems: best and common practices for metal working fluid maintenance and system design in Swedish industry

    This paper investigates the function of metal working fluid (MWF) emulsions in automotive industries in Sweden and looks at how the negative environmental and health impact of their use can be reduced through means of monitoring and system design. Major input to this study has been collected from several of the large companies in Sweden, through a literature review, interviews, questionnaires, ...


    By Inderscience Publishers

  • Wastewater Metals Removal

    Industrial Wastewater Treatment Success Stories Wastewater Treatment Metals Removal Ton Nerve Gas Agent Container Rinse Waters ...


    By Integrated Engineers Inc.

  • Metal Coating Emission Control

    The use of regenerative thermal oxidizers is expanding into applications where they wouldn’t have been considered years ago, says Mike Scholz As the first generation of oxidizer systems in the industry nears the end of their service life, many canmaking plants face repair or replacement of their existing air pollution control systems. Like many others in the industry, a Silgan canmaking ...

  • Performance specification YY: Specifications and test procedures for Xray fluorescence based multi-metals continuous emission monitoring systems at stationary sources case study

    Performance Specification YY details the performance requirements for a multi-metals continuous emissions monitor that utilizes x-ray fluorescence (XRF) as an analytical technique. Each XRF based multi-metals CEMS must meet the criteria for accuracy, stability, and instrumental response laid out in this document. In addition, every XRF multimetals CEMS must meet the installation requirements in ...

  • Procedure Z: Quality assurance requirements for X-ray-fluorescence based multi-metals continuous emission monitoring systems at stationary sources case study

    Procedure Z outlines the continuing quality control and quality assurance requirements for an x-ray fluorescence based multi-metal CEMS. Procedure Z requires daily checks of the upscale, zero and volume measurement drift. It also specifies quarterly checks of the x-ray fluorescence calibration and of the volume measurement calibration. Finally procedure Z requires that the entire XRF multi metal ...

  • On the design of advanced metal oxide nanomaterials

    A novel growth concept and a low-temperature aqueous chemical growth (ACG) thin film processing technique are presented that aim to contribute to the rational fabrication of smart and functional metal oxide particulate thin films and coatings. Such purpose-built materials are modelled, designed, and engineered to match the physical, chemical, and structural requirements of their applications. The ...


    By Inderscience Publishers

  • In-situ performance of a passive treatment system for metal source control

    ABSTRACTUrban stormwater often contains high levels of traffic-generated metal elements and particulates. These constituents are transported by stormwater runoff to surficial soils, drainage systems and receiving waters. This paper summarizes the in-situ field-scale performance of a passive treatment system called a partial exfiltration trench (PET) for source control of these constituents. For ...


    By IWA Publishing

  • Operating Experience with a Near-Real-Time Ambient Airborne Metals Instrument System

    Airborne Metals Instrument System Cooper Environmental Systems Xact 620) National Ambient Air Monitoring Conference, Nashville, Tennessee November 2-5, 2009 Missouri Department of Natural Resources, Air Pollution Control Program and Environmental Services Program Washington University, St. Louis U. S. EPA Project Plan Phase I. ...

  • Field demonstration of a near-real-time multi-metals ambient fence line monitor case study

    National emissions standards for hazardous air pollutants (HAPs) are required under Section 112 of the Clean Air Act to limit the release of specified HAPs. Permitting, monitoring and enforcement of these emission limits are an integral part of managing air quality to protect human health and the environment. However, this is difficult and highly uncertain in the case of fugitive emissions ...

  • Measurement of Trace metals in Ambient air case study

    Trace metals are found at low concentration in the ambient environment and are associated with adverse health effects. The gold standard metal measurement is Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES); however, sample preparation is laborious and expensive. The Xact 625 metals monitor uses non-destructive X-ray fluorescence technology. A built-in sample collection system ...

  • Affinity–based biosensors for heavy metal detection

    In recent years, there has been a pressing need for fast and reliable methods for environmental monitoring. Among the various pollutants, the heavy metals are some of the most harmful because these substances are non–biodegradable and retained by the ecological system. Conventional analytical techniques for heavy metals imply high cost, trained personnel and the repute that they are mostly ...


    By Inderscience Publishers

  • Britannia Refined Metals (UK) case study

    Britannia Refined Metals Ltd (BRM), the world’s largest primary refiner of lead, identified a fault in the effluent filtrationsystem at its Northfleet site in Kent thanks to the predictive powers of Monitor-Pro’s LT software. Early recognition of the fault prevented the repeated treatment of effluent that would have delayed their battery recycling process. BRM produces over 230,000 tonnes of ...


    By EHS Data Ltd.

  • On the thermodynamic stability of metal oxide nanoparticles in aqueous solutions

    Divided and ultra-divided systems such as colloidal and nanoparticle dispersions are generally unstable with regard to the size and number of their constituents because the solid-solution interfacial tension, acting as a driving force, leads to a reduction of the surface area to minimise the dispersion free enthalpy. Such phenomenon known as surface energy minimisation induces an increase in ...


    By Inderscience Publishers

  • East coast metal treatment facility recycles wastewater

    Evaporator/Crystallizer Solves Pollution Problems The Facility A major industrial Fortune 500 company manufactures armored-tracked vehicles for the U.S. Army. The plant is located in York County, Pennsylvania. The Problem Aluminum and steel assemblies and parts undergo chemical dip and spray treatments before painting. The ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you