portable hydrocarbons analyzer Articles

  • System Description for Monitoring Volatile Hydrocarbons

    To help build a comprehensive Industrial Hygiene program, Buck Scientific introduces the IH910 vapor monitoring system utilizing our model 910 gas chromatograph and IH300 air sampling train. Designed to analyze hydrocarbons in air, such as degreasing solvents and paint vapors emitted during plant operations, the IH910 penetrates the 1mg/m3 detection barrier erected by other field portable gas ...


    By Buck Scientific Inc

  • Testing Tar & Asphalt for Polyaromatic Hydrocarbons

    New regulations by the European Union require laboratory testing for polyaromatic hydrocarbons (PAHs) when recycling or disposing old tar or asphalt from road planings. Sitelab’s portable UVF-3100D and TD-500D analyzers have similar sensitivity to these types of compounds. The equipment is easy to operate and samples can be tested in the field in less than ...

  • On-Site TPH in Soil Measurements in less than 15 Minutes with Portable IR Analyzers

    On-site analysis of total petroleum hydrocarbon (TPH) concentration levels in soil are easily handled using the InfraCal TOG/TPH Analyzers manufactured by Wilks Enterprise, Inc.  The InfraCal TOG/TPH Analyzers are portable infrared (IR) analyzers that quickly determine TPH levels in less than 10-15 minutes, including the extraction.  Concentrations as low as 10 ppm to well over 10,000 - ...


    By Spectro Scientific

  • Portable Infrared Analyzers Provide On-Site Measurement of Oil and Grease Levels in Hydraulic Fracturing Water

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well.  Whether the water is going to be taken off-site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water.  Waiting for remote laboratory results to determine the oil level can take several ...


    By Spectro Scientific

  • Accurately Measure Hydrocarbon (Oil/Grease) Levels in Produced Water in Under 15 Minutes

    Determining total hydrocarbon or oil/grease levels to ensure compliance with regulatory permit requirements for discharging produced water is a worldwide problem facing the oil and gas industry.   Ensuring compliance with these regulations and avoiding fines for non-compliant discharges requires more frequent wastewater measurements to determine the total hydrocarbon ...


    By Spectro Scientific

  • Case study - NAPL forensics analysis at refinery site in Kansas

    An environmental consultant at Subsurface Environmental Solutions, LLC used Sitelab to fingerprint a large plume of Non Aqueous Phase Liquids (NAPL) located at a former oil refinery in Kansas. The plume is commingled with gasoline, diesel, crude oil and other petroleum products. Sitelab’s portable UVF-3100D analyzer is fitted with optical filters which can measure the C6 to C10 gasoline ...


    By Sitelab Corporation

  • On-Site TPH in Soil Measurements

    On-site analysis of total petroleum hydrocarbon (TPH) concentration levels in soil are easily handled using the InfraCal TOG/TPH Analyzers manufactured by Wilks Enterprise, Inc.  The InfraCal TOG/TPH Analyzers are portable infrared (IR) analyzers that quickly determine TPH levels in less than 10-15 minutes, including the extraction.  Concentrations as low as 10 ppm to well over 10,000 - ...


    By Spectro Scientific

  • Oil in frac water testing

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the wa-ter. Waiting for remote laboratory results can take several days to a week. The InfraCal TOG/TPH ...


    By Spectro Scientific

  • New ASTM Test Method Offers Quick and Easy Oil and Grease Measurement for Water and Soil Samples

    Onsite Field Measurement of Oil and Grease A quick and easy field analysis method for determining oil and grease concentration levels is important for both offshore oil platforms and soil remediation sites.. Prior to the Montreal Protocol, infrared (IR) analysis using Freon as an extraction solvent was a widely used field and laboratory method. In 1999, the U.S. EPA promulgated Method 1664A ...


    By Spectro Scientific

  • Field method developed testing asphalt for PAHs and Benzo[a]Pyrene

    New regulations by the European Union require laboratory testing for polyaromatic hydrocarbons (PAHs) when recycling or disposing old tar or asphalt from road planings.  Sitelab’s portable UVF-3100D and TD-500D analyzers have similar sensitivity to these types of compounds. The equipment is easy ...


    By Sitelab Corporation

  • Water quality and quantity assessment of pervious pavements performance in experimental car park areas

    Pervious pavements have become one of the most used sustainable urban drainage system (SUDS) techniques in car parks. This research paper presents the results of monitoring water quality from several experimental car park areas designed and constructed in Spain with bays made of interlocking concrete block pavement, porous asphalt, polymer-modified porous concrete and reinforced grass with ...


    By IWA Publishing

  • Advances in flashpoint testing: economic impact

    Flashpoint testing is one of the oldest methods of the ASTM D02 Committee on Petroleum Products and Lubricants, which was formed in 1904. The most prevalent standards are ASTM D56 (Tag Method), D92 (Cleveland Method), and D93 (Pensky-Martens Method). These classical techniques, commonly referred to as open-cup and closedcup methods, share a common principle: A test flame is lowered into the ...

  • A novel spectrometer design for process and handheld infrared spectral measurements

    Introduction Infrared spectroscopy offers many unique advantages for measurements within an industrial environment. Historically, the technique has been used for a broad range of applications from the composition of gas and liquid mixtures to the analysis of trace components for gas purity analysis. In cases where a well-defined method of analysis is involved, such as the measurement of ...


    By CIC Photonics, Inc.

  • Detecting Gases: What You Can`t Smell Can Hurt You

    Walking through a drill-site area, a worker smells rotten eggs and stops tor a minute or two to assess where a gas leak might exist. Rubbing his itchv eves as he investigates further, he notices that he no longer smells the tell¬tale hydrogen sulphide odour. He does not realize that the gas has deadened his olfactory senses and unless he leaves the area within seconds, he could lose ...

  • Organics Monitoring: A Practical Guide

    Preventing product loss, lowering waste treatment costs, and reducing system maintenance and energy consumption through organics monitoring in the chemical, refining, food, and wastewater treatment industries. Summary Process water and steam condensate contamination includes organic, inorganic, and biological components. Sources of organic contamination include process ...


    By GE Analytical Instruments

  • Selecting and Placing Gas Detectors for Maximum Application Protection

    Many industrial processes involve dangerous gases and vapors: flammable, toxic, or both. With the different sensing technologies available, and the wide range of industrial applications that exist, selecting the best sensor and locating them properly for the job at hand can be a challenge. To ensure a high level of safety, know the latest sensing technologies, which technology is best for the ...

  • Triad expedites brownfields redevelopment in Fairbanks

    The Fairbanks North Star Borough (FNSB) used Triad in 2006-2007 to assess environmental conditions at a municipal property along the Chena River in Fairbanks, AK. FNSB accelerated the site investigation as part of a brownfields assessment grant received from the U.S. EPA in 2005. Low-level contamination had been identified onsite in past investigations, but its extent and impact on future ...

  • Factors Affecting Oil in Water Testing Methods

    Various factors need to be considered when comparing methods to measure oil and grease in water.  Whether you are trying to meet effluent limits for an NPDES (National Pollutant Discharge Elimination System) permit, comply with oil and grease limits for the Clean Water Act (CWA), or an industry satisfying a POTW’s (Publically Owned Treatment Works) discharge permit, it is ...


    By Spectro Scientific

  • Detecting Mercury in Water

    Determination of Mercury (Hg) in Water by Hand-Held, Portable Cold Vapor Atomic Fluorescence SpectrometryWater is the most familiar and most abundant compound on Earth, making up 71% of its surface area.[1]It is a vital component for all known forms of life and is the aquatic habitat for thousands of species of microalgae, fish and shellfish. [2] With the presence of running water in our ...


    By Arizona Instrument LLC

  • Is your Plant as tight as you think? Leak Detector for extremely toxic Gases, a Field Test Report

    Leak detection of commodity gases in chemical plants is a day-to-day practice. The sensor technology available for this application is field proven and reliable. No question about it, existing sensors will do the job. However, in plants manufacturing or handling extremely toxic substances, the picture is different. For example, take phosgene. The existing sensor technology for leak detection ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you