portable tph analyzer Articles

  • On-Site TPH in Soil Measurements

    On-site analysis of total petroleum hydrocarbon (TPH) concentration levels in soil are easily handled using the InfraCal TOG/TPH Analyzers manufactured by Wilks Enterprise, Inc.  The InfraCal TOG/TPH Analyzers are portable infrared (IR) analyzers that quickly determine TPH levels in less than 10-15 minutes, including the extraction.  Concentrations as low as 10 ppm to well over 10,000 - ...


    By Spectro Scientific

  • On-Site TPH in Soil Measurements in less than 15 Minutes with Portable IR Analyzers

    On-site analysis of total petroleum hydrocarbon (TPH) concentration levels in soil are easily handled using the InfraCal TOG/TPH Analyzers manufactured by Wilks Enterprise, Inc.  The InfraCal TOG/TPH Analyzers are portable infrared (IR) analyzers that quickly determine TPH levels in less than 10-15 minutes, including the extraction.  Concentrations as low as 10 ppm to well over 10,000 - ...


    By Spectro Scientific

  • Comply with Highly Regulated Oil in Water Measurements Using Portable Infrared Analyzers

    The Petroleum Industry – both offshore and onshore -- has regulations that limit the amount of oil in discharged water.  Fixed filter infrared (IR) analyzers have been used to test oil levels in produced water on drilling platforms for over 45 years for a number of reasons. On oil rigs where real estate is at a premium, infrared analyzers such as the Wilks InfraCal TOG/TPH ...


    By Spectro Scientific

  • Comply with Permit Levels for Fats, Oil and Grease in Wastewater using Portable IR Analyzers

    Wilks InfraCal TOG/TPH Analyzers provide accurate, on-site analysis to help regulators and industry reduce the discharge of fats, oil and grease in wastewater.  On-site testing with the portable mid-IR InfraCal Analyzer gives results in 10 minutes and eliminates the wait for off-site lab results.  It is simple enough for an operator with minimal training to do the analysis. Stricter ...


    By Spectro Scientific

  • Portable Infrared Analyzers Provide On-Site Measurement of Oil and Grease Levels in Hydraulic Fracturing Water

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well.  Whether the water is going to be taken off-site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the water.  Waiting for remote laboratory results to determine the oil level can take several ...


    By Spectro Scientific

  • Portable IR Analyzers Provide Petroleum & Wastewater Industries with Accurate Oil Content Measurements

    Fixed filter infrared (IR) analyzers have been used to test oil levels in produced water on off-shore and on-shore drilling platforms for well over 45 years. U.S. EPA methods 418.1 and 413.2 were used extensively on a worldwide basis until the Montreal Protocol called for Freon (the solvent used in the analysis) to be phased out. Infrared analysis using tetrachloroethylene (perchloroethylene) is ...


    By Spectro Scientific

  • Oil in frac water testing

    The amount of water used in and produced by hydraulic fracturing of shale gas wells is in the millions of gallons per well. Whether the water is going to be taken off site for disposal or reused for re-injection, the flowback or produced water needs pretreatment to remove any residual oil from the wa-ter. Waiting for remote laboratory results can take several days to a week. The InfraCal TOG/TPH ...


    By Spectro Scientific

  • Infrared Analysis Reduces Regulatory Fats, Oil and Grease (FOG) Testing Costs and Provides Fast Results

    Wastewater professionals who are enforcing industrial effluent standards for fats, oil and grease (FOG) either must perform numerous gravimetric tests or spend a considerable amount of money with a contracted testing laboratory.  Infrared analysis. using portable instruments such as the InfraCal TOG/TPH Analylzers -provides an alternative which will significantly reduce costs and ...


    By Spectro Scientific

  • Accurately Measure Hydrocarbon (Oil/Grease) Levels in Produced Water in Under 15 Minutes

    Determining total hydrocarbon or oil/grease levels to ensure compliance with regulatory permit requirements for discharging produced water is a worldwide problem facing the oil and gas industry.   Ensuring compliance with these regulations and avoiding fines for non-compliant discharges requires more frequent wastewater measurements to determine the total hydrocarbon ...


    By Spectro Scientific

  • New ASTM Test Method Offers Quick and Easy Oil and Grease Measurement for Water and Soil Samples

    Onsite Field Measurement of Oil and Grease A quick and easy field analysis method for determining oil and grease concentration levels is important for both offshore oil platforms and soil remediation sites.. Prior to the Montreal Protocol, infrared (IR) analysis using Freon as an extraction solvent was a widely used field and laboratory method. In 1999, the U.S. EPA promulgated Method 1664A ...


    By Spectro Scientific

  • Emulsion-Breaking Techniques for Accurate Oil in Water Measurements

    A White Paper discusses emulsion-breaking techniques for ensuring accurate oil in water measurements. Certain water samples, such as those containing detergent, may form an emulsion when oil in water extraction into a solvent is done. In order to ensure an accurate measurement, the emulsion must be broken. Six techniques are described that can be used for reducing an emulsion ...


    By Spectro Scientific

  • What the Wastewater Industry can learn from the Petroleum Industry when it comes to measuring oil in water

    I recently read a comment in the Steve Jobs biography by Walter Isaacson that different divisions within a company do just what the name implies—divide a business.  Integration across and communication between the departments was essential to smooth functioning product.  I think the same is true in the analytical analysis/measurement world—there seems to be a divide in ...


    By Spectro Scientific

  • Emulsion breakingtechniques for oil in water solvent extractions

    Certain types of samples, such as those containing detergent, may form emulsions when doing an oil in water extraction into a solvent. The boundary between the solvent and the sample will have an emulsion layer that lias a cloudy or milky appearance as shown in tlris photo. According to U.S. EPA Method 1664, "if the emulsion is greater than one-third the volume of the solvent layer. Hie ...


    By Spectro Scientific

  • Factors Affecting Oil in Water Testing Methods

    Various factors need to be considered when comparing methods to measure oil and grease in water.  Whether you are trying to meet effluent limits for an NPDES (National Pollutant Discharge Elimination System) permit, comply with oil and grease limits for the Clean Water Act (CWA), or an industry satisfying a POTW’s (Publically Owned Treatment Works) discharge permit, it is ...


    By Spectro Scientific

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you