precision gas sensor Articles

  • Sensor design the key advantage in thermal mass flow meter performance

    Immersible thermal sensors arc finding growing acceptance in the gas flow measurement field. By using two Platinum Resistance Temperature Detectors (PRTDs) immersed in a stream of flowing gas, modern thermal flow meters can directly measure mass flow, without the need for temperature or pressure compensation. Thermal meters offer very high turndown, accu- racy and repeatability at an economical ...


    By Sierra Instruments, Inc.

  • Performance characteristics of a Thin-film aluminum oxide humidity sensor - Case Study

    Summary A laboratory study was made of the performance of a miniature-size, thin-film aluminum oxide humidily sensor over a range of ambient temperatures from 0°C to 40°C and encompassing humidities from 40 to 78,000 parts per million by volume (ppm-v). Hysteresis and temperature effects of the sensors were obtained from tests performed at ambient temperatures 40°C, 25°C and ...

  • Gas Dilution With The Equal Capillaries Technique

    The advantages of the equal capillaries technique are surprising and leads to reach accuracy values of one order of magnitude higher than all the other dynamic dilution techniques. This comparison will be supported by analyzing the accuracy available with two different techniques. Nozzles (sonic or non-sonic) technique With this technique, a series of different size nozzles is used ...


    By Be.T.A. Strumentazione Srl

  • FTIR gas analysis improves container safety

    Introduction Entry to freight containers represents a significant hazard to staff responsible for inspection, stuffing or destuffing because of the large number of airborne chemicals that can be present. Research in Germany and the Netherlands found hazardous levels of gases and vapours in around 20% of all containers and this level of contamination is now accepted as commonplace. It ...


    By Gasmet Technologies Oy

  • Benefits of HART Communication-Enabled Gas and Flame Detectors

    Catastrophic results can occur when a fire or a flammable/toxic gas release goes undetected in any petrochemical facility. For early warning and prompt hazard mitigation, flame detectors and gas detectors are essential tools. Clear, usable, diagnostic information from these detection instruments is extremely valuable in ensuring the devices are properly maintained, tested, and poised to protect ...

  • FTIR resolution requirements for industrial gas analyses

    FTIR Spectroscopy FTIR Spectroscopy is a widely used technique for gas analyses in industrial applications. It is a technique used in the semiconductor industry for measuring the purity of cleaning, etching, and epitreatment gases used with various process tools, reactors, and abatement devices. Among chemical companies and R&D faciltities, FTIR is applied to combustion ...


    By CIC Photonics, Inc.

  • FTIR resolution requirements for industrial gas analyzers

    FTIR Spectroscopy is a widely used technique for gas analyses in industrial applications. It is a technique used in the semiconductor industry for measuring the purity of cleaning, etching, and epi-treatment gases used with various process tools, reactors, and abatement devices. Among chemical companies and R&D facilities, FTIR is applied to combustion thermodynamics and stack gas emissions; ...


    By CIC Photonics, Inc.

  • Development of a novel odor measurement system using gas chromatography

    This paper describes a novel odor measurement system for creating arrays of virtual chemical sensors with nonoverlapping responses using ultrahigh-speed gas chromatography with a surface acoustic wave sensor (GC/SAW). This GC/SAW system provides high-resolution twodimensional olfactory images for easy recognition of many complex odors. Separation and quantification of the individual chemicals ...

  • Primary Standard Gas Flow Calibration—The Only Guarantee of Accuracy

    At Sierra, we have a saying: “An instrument’s accuracy is only as good as its calibration.” The accuracy of your mass flow controller (MFC) is essential in assuring the efficiency, performance, and quality of your flow meter. In many cases, if your instrumentation is not calibrated, then a decline in performance is possible due to ...


    By Sierra Instruments, Inc.

  • Wastewater Plant Relies on Thermal Flow Meter for Co-Gen Power Gas Blending Process

    The Rahway Valley Sewerage Authority (RVSA), which operates a large wastewater treatment plant in New Jersey, embarked on a green co-generation waste-to-energy project to power a portion of its operations. The plant performs primary, secondary, tertiary and sludge treatment processes in serving over 250,000 residential customers and 3000 industrial and commercial customers in a 40-plus square ...


    By Modern Pumping Today

  • Paint booths, or areas using combustible gases: why a requirement for combustible gas monitor might be necessary

    Paint booths save time and ensure a smooth and professional application of paint in a range of industries, including automotive, aerospace, home decor, furniture, and more. Combustible gases and fluids in the paint booth environment can pose a health hazard if something goes wrong. Explore the hidden dangers of paint booth fluids and gases, and learn how a ...

  • Inno-badge – an electronic dosimeter badge for continuous recording of a worker`s exposure to Phosgene gas

    Untitled Document Phosgene, also known as Carbonyl Chloride, is a widely used but highly toxic substance. At room temperature Phosgene gas is nearly colourless, and at low concentrations ...


    By Baum Publications Ltd.

  • Wastewater force main management – internal corrosion survey using inline methods

    In our first post about Wastewater Force Main Management, we looked at how preliminary analysis helps operators develop a plan for managing their system. After completing this process, operators can begin putting the plan into action with preliminary surveys on specific force mains. For those at WEFTEC, you can visit Pure ...


    By Pure Technologies

  • Wastewater Force Main Management – Internal Corrosion Survey using inline methods

    In our first post about Wastewater Force Main Management, we looked at how preliminary analysis helps operators develop a plan for managing their system. After completing this process, operators can begin putting the plan into action with preliminary surveys on specific force mains. For those at WEFTEC, you can visit Pure ...


    By Pure Technologies

  • Distributed Thermal-Acoustic Data Integration

    Silixa has developed a technique called Distributed Thermal Acoustics (DTA) to monitor simultaneously the thermal and acoustic profile along a hybrid optical fibre cable in submarine environments. Using its world leading distributed fibre optic technology (ULTIMATM DTS and iDASTM) Silixa deployed an optical fibre cable along the seabed and across the water column in an active gas seepage ...


    By Silixa Ltd

  • Tech update: Plant instrumentation - food engineering

    Sensors and other devices are the foot soldiers in automation architecture, but most food and beverage manufacturers still are looking for full value. You know an equipment category has arrived when it starts getting its own industry-specific center. For the food production sensors that do the heavy lifting in instrumentation technology, that day could arrive earlier rather than ...


    By Hardy Process Solutions

  • What is an `IAQ Profile`?

    The 'IAQ Profile' is a visual presentation of indoor air quality. PPM Technology's range of IAQ Monitors enable continuous monitoring of Indoor Air Quality; this precisely describes changes in concentration levels of selected air quality parameters over a period of time.  The IAQ Profile provides the knowledgebase and database for improving indoor air quality efficiently and ...


    By PPM Technology

  • Japanese Organics Recycling Association Formed

    Another backyard composting adage states that compost should have the feel of a wrung-out sponge — damp but not dripping wet. Actually, a wrung-out sponge may be on the dry side for composting, but the analogy does provide a great image for understanding the reasons for balancing moisture. Like a compost pile (or windrow or material in a vessel), a sponge is a solid mass containing an enormous ...


    By BioCycle Magazine

  • Two Technologies for Flow Measurement from Outside a Pipe

    Doppler and Transit Time are two very popular types of flow meter for non-invasive measurement of flow in full pipes. We tend to confuse these technologies because they are both ultrasonic and both measure flow by using sensors clamped onto the outside of a pipe. In the real world they actually work best in opposite applications. Success in your installation depends on understanding the ...


    By Greyline Instruments Inc.

  • Expect The Unexpected During Inline Inspection Runs

    Over the past decade, several high profile oil and gas pipeline failures have shown that the consequences of a rupture can be extremely severe for both the environment and human life, and can result in billions of dollars in remediation costs. Because of all these negative consequences, governments have made it mandatory to conduct routine inspections on these assets to prevent catastrophic ...


    By Pure Technologies

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you