pressure sensor manufacturer Articles

  • Pressure transmitters: It’s class that counts

    KELLER would like to do away with DIN standards. The company is backing the introduction of an accuracy class, as it did for pressure gauges. The conditions under which the class is complied with are described in specifications. The new EC standards make it more difficult for companies to manufacture their own transmitter electronics. Changing from OEM transducers to OEM transmitters is ...

  • Calibration of Thermal Conductivity Sensors for Measuring Soil Suction

    The accuracy of suction measurements using thermal conductivity sensors is dependent upon their calibration. Therefore, a calibration study was undertaken by using a modified, commercially available, pressure plate extractor. The experimental setup along with the calibration procedure are described. Typical calibration results are presented. In general, results showed reasonable agreement between ...


    By ASTM International

  • Are environmental monitoring manufacturers pulling a fast one with back-to-base servicing?

    Geotech's users of environmental monitoring equipment are not alone in their frustration at having valuable equipment unavailable when they require servicing.  Is this just a money-making scam?  What do users get for their money?  By combining maximum possible local support with a 100-point factory full service schedule, Geotech believe they have the best balance of user ...


    By Geotech

  • The duty-factor - choosing a quality high pressure system

    Definition of Duty-Factor The duty-factor of your pump or system could simply be the product life. Or the duty-factor could be more specifically defined as the length of time a pump or system runs between servicing and the type of performance during this time frame. Elements determining Duty-Factor The duty-factor is affected by many variables including ...


    By Cat Pumps

  • Oxygen (O2) Monitors: Disposable Sensors eating your Cash? PureAire Introduces 10 + Year Sensor.

    PureAire Monitoring Systems is a leading manufacturer in the gas monitoring industry. When it comes to O2 deficiency monitors PureAire makes the most reliable, longest lasting, and affordable oxygen monitors. It has been an international standard for the past three decades to use oxygen monitors with disposable sensor cells, (electrochemical sensors). All disposable sensors require frequent ...

  • Stop metal losses in processes with Sulphide, Cyanide, Ammonia and Pressure Fluctuations

    Abstract Losses of metal are often traced to incorrect pH/ORP signals in floatation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls a Canadian mining sensor manufacturer developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP ...


    By IC Controls Ltd.

  • Top 10 Valve Considerations for Pressure Management Zones/DMA’s

    For basic pressure management or more advanced modulating pressure management, water suppliers create a network of District Metered Areas (DMA’s) or smaller, more manageable pressure management zones. The DMA or pressure zone gives the ability to measure flow and control pressure, when a Pressure Reducing Valve (PRV) ...


    By Singer Valve Inc.

  • Safety Systems Depend on Reliable Field Sensors (Emphasis on Fire and Gas Detectors)

    Abstract Because not all hazards are the same, identifying and quantifying the hazard is the starting point in choosing sensing technology. Not all detectors are the same, and they should be selected according to their ability to detect the hazard. This paper gives a broad summary of technologies that provide users reliable responses to hazardous conditions, that minimise false ...

  • Are You An OLED Display Manufacturer? Why PureAire Monitoring Systems May Be Your Next Partner

    OLED -- organic LED -- is a top desired feature in smartphones, yet manufacturers do not have the production capacity needed to meet industry demands. Since OLED devices have stronger contrast, a faster response time, a better quality, and a lower cost, there are many reasons for consumers as well as ...

  • Smart PV Monitoring with smart Weather Stations

    Goodbye Cable Clutter, Hello All-In-One Weather Sensors: Lufft is proof of the fact that professional measurement technology does not always have to be complicated. With our experience in weather sensor manufacturing we are the first to offer modular, all-in-one weather sensors for the solar energy industry that require only a single cable connection. Everything you need for solar monitoring is ...

  • Water Level Measurements-Part 1

    Confused about which instrumentation to use in your water level monitoring system? In-Situ offers two categories of pressure sensors for water level measurements: absolute or non-vented sensors, and gauged or vented sensors. They look the same and both measure pressure and water level, but they have drastically different applications, outputs and accuracy. The absolute (or non-vented) water level ...


    By In-Situ, Inc.

  • PureAire Makes Oxygen Monitor for Nitrogen Generators

    Nitrogen generators are most commonly used in areas where on-demand nitrogen is preferred rather than, storing liquid nitrogen (LN2) in cylinders.  Nitrogen generators have a lower cost of operation, and can be used where smaller amounts of nitrogen are needed. Nitrogen generators are used in the pharmaceutical industry, testing laboratories, cryogenic facilities, welding manufactures, and ...

  • Wind turbine controlling of the future

    Higher, more robust, more reliable: Parallel to the growing requirements for wind turbines, the requirements for monitoring sensors grow as well. But how can wind sensor manufacturers fulfil these wishes? And how should a future wind sensors look like? After analysing the current conditions and trends on the wind energy market, our CEO Klaus Hirzel compiled a wish list for future wind sensors. ...

  • Current advances in sustainable Metalworking Fluids research

    Metalworking Fluids (MWFs) have a history of harming the environment and the health of workers, resulting in pressures to re-design them in accordance with sustainable manufacturing principles. In this paper, we review research being performed at the University of Michigan to minimise the life cycle environmental and health impacts of MWFs while simultaneously improving manufacturing performance. ...


    By Inderscience Publishers

  • Reducing Costs of Steam Flow Measurement

    Traditionally, steam flow has been measured with a differential pressure device. This is typically an orifice plate. However, such devices are inherently volumetric flow measurements. As we have discussed in previous blog posts, changes in pressure and temperature ...


    By Sierra Instruments, Inc.

  • Portable Hydrant Flow Meters

    Leading the way for hydrant verification flow and pressure measurement Langham Industrial Controls strive to provide the most innovative market leading hydrant verification instrumentation. The Horizontal Standpipe Flow Meter provides unrivalled accuracy of ± 0.5% within a wide flow range. The swan neck design ensures that the AquaMasters electromagnetic sensor is always full and as the ...

  • Tech update: Plant instrumentation - food engineering

    Sensors and other devices are the foot soldiers in automation architecture, but most food and beverage manufacturers still are looking for full value. You know an equipment category has arrived when it starts getting its own industry-specific center. For the food production sensors that do the heavy lifting in instrumentation technology, that day could arrive earlier rather than ...


    By Hardy Process Solutions

  • Ultrasonic Testing For Non Destructive Testing

    Ultrasonic Testing or UT as its known has programs in a wide range of sectors, from aerospace, automobile, to substance, oil, large storage space, and power creation and overseas. UT is aspect of a selection of techniques known as NDT (Non Destructive Testing) methods. Their objective in industry is to allow the examination of parts and equipment ...


    By Non Destructive Testing Lab

  • Future inside – smart environmental sensing technology

    SHM30 snow depth sensor in Antarctica (photo: Alfred-Wegener-Institut, Helmholtz-Zentrum Bremerhaven) A lot of sensing technologies have changed recently: Ultrasonic wind measurement replaces cups and vane systems, closed anemometer designs offer better protection from ...

  • Get the scoop on the newest technology for the measurement of pH

    SENTRON had its 20th birthday in April 2005 and is world wide known as the manufacturer of glass free ISFET (Ion Sensitive Field Effect Transistor) pH systems. During the 20 years we developed and manufactured not only ISFET pH sensors but also pressure sensors in our own silicon chip production facility. This facility for development and manufacturing of solid-state sensors, enables us to ...


    By Sentron Europe BV

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you