pulse-jet filter bag Articles

  • Solid / gas separation with fabric filters

    A myriad of filter media are utilized today for separation of particulate matter in industrial gas filtration applications. These media range from single use (deposable) to semi-permanent media and include fiber, fabric, ceramic, membrane, metal mesh, and sintered metal media. Semi-permanent media are usually cleanable, either on or off-line, and are primarily intended for long-term (up to ...

  • Filter Your Air with Cartridge Dust Collector

    A cartridge dust collector uses filtering cartridges and is a self-cleaning dust collector. The cartridges it uses are made from synthetic fibers and cellulose that is treated chemically. This ensures the particles are efficiently collected without forming an excessive pressure drop in the system. Structure A cartridge dust collector uses an air-jet cleaning structure to preserve ...


    By ProVent, LLC

  • Chemical-Free Treatment of Recirculating Water Using Pulsed-Power

    Untitled Document Regulatory pressures and economic considerations require industry to become cleaner, more efficient, and more environmentally benign. Such operating principles advance not only ...


    By Dolphin WaterCare

  • The Use of Particulate Emission Monitors to Support Arrestment Plant Operation and Upkeep

    The operation of filtration type arrestment plant can be optimised by the effective use of Particulate Emission Monitors (eg Filter Leak Monitors and Filter Performance Monitors). Particulate Emission Monitors are installed throughout the broad spectrum of industrial processes to satisfy regulations (IPPC, Part B Guidance Notes, WID and LCPD) for emission limit enforcement. In addition, where ...


    By PCME Ltd

  • Advantages of cleaning without a venturi in baghouse collectors

    ABSTRACT: Background The cleaning cycle is the most important part of the dust collector because it controls efficiency and media life. In order to clean a row of bags in a reverse pulse jet baghouse first the flow of filtered air must be momentarily stopped and then back flushed or “induce” air to knock the dust cake off the outside of the filter media. A venturi at the top of the ...


    By Scientific Dust Collectors

  • Improving the cleaning cycle in baghouse collectors

    ABSTRACT: Background The reverse pulse jet baghouse has been around for over 45 years and the cleaning cycle has not changed very much since that time. The cleaning cycle is the most important part of the dust collector because it controls efficiency and media life. In a generic baghouse, the cleaning system is comprised of a blowpipe that is located typically approximately three inches above ...


    By Scientific Dust Collectors

  • Pilot and Industrial-Scale Experimental Investigation of Numerically Optimized Cyclones

    A new geometry of reverse-flow gas cyclones obtained by numerical optimization was shown at the laboratory scale to be significantly more efficient than other high-efficiency designs. However, it is usually recognized that experimental results obtained with laboratory-scale or sampling cyclones cannot be extrapolated to pilot or industrial scales. The present paper confirms, at these larger ...

  • New Nozzle Technology “Cleaning More with Less”

    This technical paper will explain the new nozzle technology developed by Scientific Dust Collectors that allows high air-to-cloth ratio baghouses to use 80psig of compressed air instead of the industry standard 100psig.   The reverse pulse jet baghouse has been around for over 50 years and the cleaning cycle has not changed very much during that time. The cleaning cycle is the most important ...


    By Scientific Dust Collectors

  • Fine particle capture in biomass boilers with recirculating gas cyclones: Theory and practice

    This paper addresses the theoretical development and experimental validation of optimized recirculating reverse-flow gas cyclones. The simulation of these systems is based on the predictive properties of a finite diffusivity model, modified to include partial recirculation of the cyclones' emissions. Experimental validation was obtained at laboratory and pilot scales at low temperatures (up to ...

  • Laboratory, pilot and industrial-scale validation of numerically optimized reverse-flow gas cyclones

    This paper addresses the experimental validation of the optimum design of reverse-flow gas-cyclones, obtained through the solution of a numerical non-linear optimization problem, viz. maximizing cyclone collection. The simulation model is based on the predictive properties of a finite diffusivity model, where the particles' turbulent dispersion coefficient is estimated through an empirical ...

  • Ineffective cleaning in generic baghouses

    ABSTRACT: Background In a typical “generic” baghouse application, the cleaning is accomplished by back-flushing the filter with compressed air that travels through an orifice hole in a purge tube (blow pipe) and through a venturi. A typical generic cleaning system allows dust to be filtered at an air-to-cloth ratio of 5:1. That means for every 5 CFM of airflow, there is 1 square foot ...


    By Scientific Dust Collectors

  • Air filtration applications for membranes

    Given their unique performance attributes membranes are finding use in a growing number of high efficiency air filtration applications. One example is in respirators and personal protective equipment. Applications where intense physical demands and risk of exposure to harmful contaminants are present demand the high efficiency / low pressure drop combination of expanded polytetrafluoroethylene ...

  • Moving difficult-to-handle bulk materials with flexible screw conveyors

    Flexible screw conveyor systems can be engineered to transport bulk materials that tend to pack, cake, smear, break apart or fluidize, and can prevent the separation of blended products. Flexible screw conveyors (Fig. 1) are suitable for most bulk materials, from sub-micron powders to large pellets, both free-flowing and non-free flowing. They are capable of conveying bulk materials at any angle ...


    By Flexicon Corporation

  • Controlling scale deposits in the pulp & paper industry

    The pulp and paper industry is one of the heaviest users of water within the North American industrial economy, requiring on average 54 cubic meters of water per metric ton of finished product.  As water is used in nearly every part of the manufacturing process, accumulation of scale is a phenomenon that can occur in all pulp and paper making processes. This occurs even with the purest water ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you