recuperative catalytic oxidizer Articles

  • Recuperative oxidizer - Boat engine manufacturer

    Epcon has extensive experience in designing and building Thermal Oxidizers for Engine Cell Testing. The Problem A major Boat Engine manufacturer needed to lower emissions from engine cell testing. All motors, whether automobile or boat, are Pre-Tested for several hours prior to shipping. The emissions from these Engine Cells are mostly Carbon Monoxide and unburned fuel, with ...


    By Epcon Industrial Systems, LP

  • Recuperative Thermal Oxidizers for Coffee Roasting

    Coffee Roasting Company Epcon has extensive experience in designing and building Recuperative Thermal Oxidizers for the Coffee Roasting Industry. The Problem A leader in the Coffee Industry needed equipment to control odor and eliminate VOC's from Coffee Roasting. The company went out seeking the technical solutions and went to several manufacturers to ...


    By Epcon Industrial Systems, LP

  • Hi Tech company selects PSSI oxidizer - innovative solar panel manufacturer selects PSSI recuperative catalytic oxidizer

    Background PSSI was initially contacted to provide an innovative company with support to determine which air pollution control technology was most appropriate for their new product line used in the production of solar panels.  The product had been under development for many years and was now ready for commercial manufacturing.  PSSI worked closely with the company to understand their processes ...


    By Pollution Systems

  • Air Pollution Control Using Catalytic, Regenerative or Recuperative Systems

    For companies in a variety of industries, the clock is ticking regarding their compliance with local, state and federal clean air requirements. The need to provide adequate emission controls still looms on the horizon as these companies explore the various equipment and technology options available to them. While the guidelines regarding air pollution control are consistent by industry, a ...


    By The CMM Group, LLC

  • Case study - Recuperative Thermal Oxidizers and midstream natural gas processing

    A large midstream natural gas processing facility was in urgent need of a VOC abatement device for their newly expanded gas processing plant. The operator was expanding their operations at an unusually fast pace. In the process of bringing on new gas treating capacity, they found themselves up against the limits of their current operating permit. Any new sources would put them over their limits ...

  • Case study - Catalytic products international replaces RTO with a VECTOR Catalytic Oxidizer

    A chemical processing facility recently installed a VECTOR Catalytic Oxidizer to replace a competitors Regenerative Thermal Oxidizer. The RTO was installed 5 years earlier and could not provide the reliability demanded by the client. The problem stemmed from a basic mis-application of the technology. As is very common, many air pollution control equipment manufactures have abandoned recuperative ...

  • High efficiency thermal oxidizer - feed products manufacturer selects PSSI high efficiency recuperative oxidizer

    Background Pollution System Solutions was engaged to provide air pollution control technology for a Feed Products Manufacturer that needed to increase production capacity in its Midwest facility.  The new equipment was required to effectively reduce odors in 40,000 SCFM of VOC laden process air generated in the production of animal supplements.  Additionally, long term reliability and on-going ...


    By Pollution Systems

  • Case study - Styrene emissions: Catalytic oxidizer with concentrator

    Overview The world's largest button manufacturer needed a pollution control system that would destroy styrene emissions from a variety of plant processes. The plant was proactively seeking a cost-effective air pollution control solution to preempt future regulatory action. The main concern of the customer was the high operating cost of an emission control system. ...

  • A Comprehensive Review Of Regenerative Thermal Oxidizers

    Within industry today, the use of an Air Pollution Control System (APCS) to control harmful air pollutants is not new. In response to Congressional guidelines passed in the 1970’s, a number of companies with VOC emissions have been operating air pollution control systems of one type or another for 25 years or more. These guidelines have been revised and added to as the years progressed, making it ...


    By The CMM Group, LLC

  • Comparison of a Regenerative Thermal Oxidizer to a Rotary Concentrator

    INTRODUCTION The regenerative thermal oxidizer (RTO) is a very durable, well-proven technology suitable for treating a wide variety of emission streams. However, The RTO may not be the most economical technology available. Two very common systems for treating emissions from coating and finishing processes are the RTO and the concentrator/ oxidizer system. To determine which system is best suited ...

  • Can coater chooses the Quadrant SR Thermal Oxidizer

    A can manufacturer worked with Catalytic Products International, Inc to design a unique Thermal (recuperative) Oxidizer. A recuperative thermal oxidizer was chosen over other thermal oxidation systems because of high solvent loads exhausted from the company’s can coating lines and a desire to integrate customized energy recovery system. After careful examination of the process ...

  • Case study - Oxidizer system optimization

    OXIDIZER SERVICE SERIES: PART 4 As promised, this is the fourth installment of Anguil's Oxidizer Service Series. If you have read through the first three parts, this can be seen as a capstone of those efforts. Having a strong oxidizer service plan, backed up with recommended spare parts and all of the proper documentation will not only improve your system performance but also allow you to focus ...

  • The QUADRANT SR Series Thermal Oxidizer and the textiles industry

    A synthetic leather manufacturer worked with Catalytic Products International, Inc. to design a unique Thermal (recuperative) Oxidizer. A recuperative thermal oxidizer was chosen because of high solvent LEL (+25%) exhausted from the process and a desire to integrate a hot oil recovery system to work with the oil heated production coating/curing line. After careful examination of the process ...

  • How to Optimize Oxidation Systems for Efficient Operation

    Emphasis on air management within converting-process dryers and ovens is critical to the design of pollution-control systems for treating exhausts containing VOCs (volatile organic compounds). Efficient air management allows the pollution-control system to be optimally sized to meet the needs of the process. Good process control further defines the emission stream by avoiding the need for large ...


    By Babcock & Wilcox MEGTEC

  • Thermal oxidizers for natural gas savings - Case Study

    It’s in the news every day; the natural gas production industry is experiencing record growth. The gas reserves in the United States are thought to hold enough natural gas for hundreds of years and the gas and oil industry has improved extraction techniques that make gas production more affordable and less impactful on the landscape. Good news for the country and our environment. The ...

  • Medical implant manufacturer succeeds with the QUADRANT SRS Silicone Series Thermal OXidizer

    Medical Implant Manufacturer Succeeds with Customized Air Pollution Control Equipment Many industries utilize silicone as an ingredient in their manufactured product. Silicone enhances the attributes of the product or helps to improve production characteristics. Whatever the reason may be, users of solvent borne silicone's all face very troubling issues when it comes to the selection of the right ...

  • Regenerative Thermal Oxidizers…What You Should Know.

    Within industry today, the use of an Air Pollution Control System (APCS) to control harmful air pollutants is not new.  In response to Congressional guidelines passed in the 1970’s, a number of companies with VOC emissions have been operating air pollution control systems of one type or another for 25 years or more.  These guidelines have been revised and added to as the years ...


    By The CMM Group, LLC

  • Case study - Maximizing heat recovery from your oxidizer and reducing operating costs

    More and more, companies operating air pollution control equipment today realize that the initial capital cost of an oxidizer system can be rapidly eclipsed by continued operating expenses if careful attention is not periodically given to the system. Below are ten tips to ensure your oxidizer is operating at peak performance. The first five tips focus on parameters end-users should know about ...

  • Case Study - Heatset Web Offset Printing (2)

    Problem: New press additions required more oxidizer capacity than the existing systems could provide. Equipment: Unit #1: Refurbished Catalytic Recuperative; 4000 scfm (1985); Installed 2002.                     Unit #2: Refurbished Catalytic Recuperative; 5000 scfm (1993); Installed 2003.                     Location: Florida Project ...


    By Kono Kogs, Inc.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you